* Change config entry state to an enum
* Allow but deprecate EntryState str equality comparison
* Test fixes
* Rename to ConfigEntryState
* Remove str comparability backcompat
* Update new occurrences of strs cropped up during review
* Unused pylint suppression cleanups
* Remove outdated pylint bug references
* Add flake8-noqa config and note to run it every now and then
* Add codes to noqa's
* Unused noqa cleanups
* Make async_get_device connections Optional, default None
* Remove unnecessary async_get_device connections arg usages
Some of these were using an incorrect collection type, which didn't
cause issues mostly just due to luck.
* Add tilt control for RFXtrx Rfy venetian blinds
* Update Rfy cover test
* Update the required version of pyRFXtrx
* Update required pyRFXtrx version to 0.26.1
* Revert "Update required pyRFXtrx version to 0.26.1"
This reverts commit d54f1645d5.
* Revert "Update the required version of pyRFXtrx"
This reverts commit ac36d65326.
* Update required version of pyRFXtrx to 0.26.1
* @dzukero
Update required version of pyRFXtrx to 0.26.1
* Make requested changes from review
* Fix isort
* Remove set tilt position support
* Remove set tilt position support per review
* Added missing unit for signal strength
* Added one more unit
* Replaced string with variable
* Fixed wrong import
* Fix import
* Replaced string with variable
* Fixed wrong import
* Apply suggestions from code review
* Black
* Again a fix :-(
* iSort
* iSort after merge
Co-authored-by: springstan <46536646+springstan@users.noreply.github.com>
* Add more units and device classes
* Battery level is a value beteen 0 and 9 where 9 indicate full
Actual 0 battery can't occur since since then we would get to signal
* Adjust tests
* Add wind direction and adjust rain rate
* Adjust data types to be None rather than empty string
* Set counter values to count unit
* Forgotten unit
* Add binary sensor support to motion sensors and smoke detectors
* Add support for new sensor events as binary sensors
Adds a default device_class for motion sensors and smoke detector
* Use device type instead of event to set class
* Add some additional binary values
* Implement unload entry
* Change async_remove to remove
* Pop data from hass.data
* Change sequence order in unload
* Dont unload internal when unload platforms fail
* Switch to config flow setup
* Add minimal test for config flow
* Add myself as codeowner and address some review concerns
* Address some further review comments
* Switch to integration level config
* Switch to per device config rather than per entity type
* All roller shutters should be added as covers
(there are non lighting types)
* Fixup tests that used invalid packets for platforms
* Avoid variable re-use
* Allow control events on sensors too
That way we get signal level sensors for these too
* Lint correction
* Don't filter sensors from config
Disable sensors from GUI if the entities are not wanted
* Correct usage of ATTR_ instead of CONF_
* Make sure the logging when a new entity is added includes the event
* Switch to dispatcher
* Adjust tests for dispatcher
* Store device in sensor
* Move state application into binary sensor entity class
* Move more specifics into per platform classes
* Should not apply event in init of sensor
* Switch to call_later
* Make apply_event public
* No point in slugifying debug logs
* Adjust error in off delay and event
* Make sure we match with masked id
* Switch tests to use hass objects instead of direct
* Make sure sensor update state
* Add some initial binary sensor tests
* Add initial binary sensor tests
* Add tests for pt2262
* Add test for off delay
* Rework and re-enable rfxtrx tests
* Add missed change to _signal_event
* Fixup the dummy serial that causes max cpu
* Make sure we cleanup thread here too
* Make sure we always wait for tasks before we check state
* Some more places we need to wait before checking
Børge Nordli
Rob Bierbooms
Ville Skyttä
Erik Montnemery
Joakim Plate
dzukero
Franck Nijhof
Alexei Chetroi
Paulus Schoutsen
Simone Chemelli
springstan
javicalle
Paulus Schoutsen