* Add mysensors IR switch device and service
* Add MySensorsIRSwitch as child class to MySensorsSwitch.
* Add platform specific service mysensors_send_ir_code. Only call
device method in service function if device is IR device.
* Add service and required attribute to state helper to support scenes.
* Move V_IR_SEND type from sensor.mysensors to switch.mysensors
platform.
* Populate switch.services.yaml with service descriptions.
* Fix check of entity_id in service function
Since multiple entity_ids can be passed as service data, and the
entity_id service attribute is forced to a list by the service
validation schema, the check in the service function should iterate
over any entity ids.
* Add MySensorsDeviceEntity class to hold the common attributes,
properties and methods for mysensors entities.
* Inherit from MySensorsDeviceEntity class in binary_sensor, light,
sensor and switch mysensors platforms.
* Remove not needed attribute and method for const in GatewayWrapper
class. The const attribute is already set in the wrapped object.
* Clean up state property for mysensors sensor entities.
* Inherit from MySensorsLightRGB in MySensorsLightRGBW class.
* Remove use of get_component in mysensors component and platforms.
* Clean up update method in MySensorsDeviceEntity class.
* Bump version of pymysensors to 0.6, which includes the tcp gateway.
* Update requirements_all.txt.
* Replace CONF_PORT with CONF_DEVICE and ATTR_PORT with ATTR_DEVICE.
* Add tcp_port in config.
* Try to guess if tcp or serial gateway is configured, by validating
device name as an ip address. If successful setup tcp gateway, if it
fails, setup serial gateway.
* Update device_state_attributes to show correct device, ethernet or
serial.
* Add mysensors binary sensor.
* Add discovery platforms to binary_sensor base component.
* Replace device_state_attributes with state_attributes in
binary_sensor base class.
* Fix docstrings.
* Add discovery of binary sensor to mysensors component.
* Add child.type as argument to mysensors device_class.
* Move binary sensor types from sensor to binary_sensor module.
* Fix binary_sensor attribute tests. Use state_attributes instead of
device_state_attributes.
* Make a flatter one level inheritance, with MySensorsLight as parent
with four children, one per light type.
* Break out helper methods. One per plain light, dimmer and RGB/RGBW
children and per update, turn_on and turn_off, nine in total. Put
these in the parent.
* Call the helper methods as needed from the child methods update,
turn_on and turn_off.
* Change name of MySensorsLightLight to MySensorsLightPlain.
* Fix module docstrings according to pep257.
* Change name of color util method from rgb_hex_to_list to
rgb_hex_to_rgb_list.
* Add unit tests for rgb_hex_to_rgb_list.
* Make light controllable independently with types V_LIGHT, V_DIMMER,
V_RGB and V_RGBW. V_RGBW is not implemented in the frontend yet.
* Add discovery for light platform.
* Add optimistic mode config setting for switch and light
to allow feedback state from actuator.
* Move S_LIGHT, V_LIGHT, V_STATUS types from switch to light platform.
* Change node update logging to debug from info level.
* Fix some inaccurate comments.
* The application of the version check in unit_of_measurement was
messed up after the last refactor. Fix that again.
* An error could occur in device_state_attributes if there was a
mismatch between used value_type in the device and mysensors
version in config. Add try... except to handle that.
To be able to handle new platforms with multiple used v_types but
single states, a new more strict mapping was required. Each s_type is
now mapped to its corresponding v_type(s) in a dict of lists.
* Add version check in unit_of_measurement, to avoid error.
* Remove not needed metric check in unit_of_measurement.
* Add more value types to unit_of_measurement.
* Fix unit prefix
* Remove unused SCAN_INTERVAL variable.
Devices were not added without persistence enabled and restart of HA.
Node id was added to defaultdict(list) by mistake when checking if list
of defaultdict was empty.
* Fix adding devices in mysensors_callback.
* Change devices to regular dict.
* Wrap existing SerialGateway instance instead of subclassing
SerialGatewat class.
* Add S_BINARY in switch platform only in version 1.5 of mysenors api.
* Use version 0.4 of pymysensors.
* Show gateway port as state attribute.
* Fix cleaner user config.
* Remove bad disabling of linting.
* Extract default mysensors version into constant.
* Clean up selection of mysensors.CONST from version.
* Update mysensors update decorator to add devices and update values
in one go.
* Fix persistence update.
* Clean up setup of ports.
* Setup of mysensors platforms from main mysensors component.
* Clean up v_types selection in mysensors sensor platform.
* Fix s_types and v_types selection version dependency in platforms.
* Add support for multiple serial gateways.
* Fix serialization of python objects by adding dict representation of
classes.
* Add support for showing more than one child value type per entity.
The entity state is always only one value type. This is defined by
the platform value types. Value types that are not defined as the
platform value type are shown as state_attributes.
* Add more unit of measurement types.
* Clean up code.
* Add a general mysensors component. This sets up the serial comm
with the gateway through pymysensors. The component also
contains a decorator function for the callback function of
mysensors platforms. Mysensors platforms should create a
function that listens for the node update event fired by the
mysensors component. This function should call another
function, that uses the decorator, and returns a dict. The dict
should contain a list of which mysensors V_TYPE values the
platform handles, the platfrom class and the add_devices
function (from setup_platform).
* Change existing mysensors sensor platform to depend on the new
mysensors component.
* Add a mysensors switch platform. The switch platform takes
advantage of new functionality from the the fork of pymysensors
https://github.com/MartinHjelmare/pymysensors, that enables the
gateway to send commands to change node child values.
* Change const and is_metric to global constants, in the mysensors
component and import const depending on the mysensors version
used.
* Change variables devices and gateway to global variables.
* Add some debug logging at INFO log level.
Martin Hjelmare
Fabian Affolter
Paulus Schoutsen
Fabian Affolter
Andrew Thigpen
Ryan Kraus