from Adam Goldman <adamg@pobox.com>
This patch makes udhcpd respond correctly to queries from BOOTP clients.
It contains the following changes:
The end field, or DHCP_END option, is required in DHCP requests but
optional in BOOTP requests. However, we still send an end
field in all replies, because some BOOTP clients expect one in replies
even if they didn't send one in the request.
Requests without a DHCP_MESSAGE_TYPE are recognized as BOOTP requests
and handled appropriately, instead of being discarded. We still require
an RFC 1048 options field, but we allow it to be empty.
Since a BOOTP client will keep using the assigned IP forever, we only
send a BOOTP reply if a static lease exists for that client.
BOOTP replies shouldn't contain DHCP_* options, so we omit them if there
was no DHCP_MESSAGE_TYPE in the request. Options other than DHCP_*
options are still sent.
The options field of a BOOTP reply must be exactly 64 bytes. If we
construct a reply with more than 64 bytes of options, we give up and log
an error instead of sending it. udhcp_send_raw_packet already pads the
options field to 64 bytes if it is too short.
This implementation has been tested against an HP PA-RISC client.
function old new delta
.rodata 105247 105321 +74
udhcpd_main 1520 1591 +71
send_offer 419 470 +51
init_packet 81 97 +16
udhcp_init_header 75 88 +13
udhcp_scan_options 192 203 +11
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 6/0 up/down: 236/0) Total: 236 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Based on patch by Uwe Kleine-König.
It makes sense to actually see the nitty-gritty details of DNS
querying, so bringing in (commented-out) musl's DNS request code.
function old new delta
nslookup_main 760 822 +62
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
If cgi-bin/ prefix is seen, do not test the rest for existence,
whether it's a dir, and such.
function old new delta
handle_incoming_and_exit 2200 2212 +12
Reported here:
https://lists.zx2c4.com/pipermail/cgit/2023-March/004825.html
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Need to divide by (1<<32), not by (1<<32)-1.
Fraction of 0xffffffff is not 1 whole second.
function old new delta
.rodata 105264 105268 +4
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The 32-bit integer part of the NTP timestamp overflows in year 2036,
which starts the second NTP era.
Modify the timestamp conversion to shift values between 1900-1970 (in
the first era) to the second era to enable the client to measure its
offset correctly until year 2106 (assuming 64-bit time_t).
Also update the conversion from double used when stepping the clock to
work with 64-bit time_t after reaching the maximum 32-bit value in 2038
and the server conversion to work correctly in the next NTP era.
function old new delta
lfp_to_d 51 64 +13
step_time 326 332 +6
.rodata 105260 105264 +4
d_to_lfp 100 86 -14
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 3/1 up/down: 23/-14) Total: 9 bytes
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Various tools are Linuxish and should thus only attempted to build on
Linux only. Some features are also Linux-only.
Also, libresolv is used on all GNU platforms, notably GNU/Hurd and
GNU/kfreeBSD.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
-a meant both "don't up iface before each link detection" and "don't up iface
when it newly appears". But they are not the same.
I have a dock station where eth1 appears when I attach the notebook to it
(looks like it's hanging off a USB bus). IOW: appearance of this interface
is functionally equivalent to attaching ethernet cable.
ifplugd meant to be able to *automatically* handle this case.
Currently, with -a, it couldn't: newly appearing iface stayed down,
user had to manually up it.
function old new delta
packed_usage 34253 34296 +43
.rodata 104876 104877 +1
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 2/0 up/down: 44/0) Total: 44 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
The result of looking at "grep -F -B2 '*fill*' busybox_unstripped.map"
function old new delta
.rodata 108586 108460 -126
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-126) Total: -126 bytes
text data bss dec hex filename
970412 4219 1848 976479 ee65f busybox_old
970286 4219 1848 976353 ee5e1 busybox_unstripped
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
udhcp_insert_new_option treats code for IPv6 as follows:
new->data[D6_OPT_CODE] = code >> 8;
new->data[D6_OPT_CODE + 1] = code & 0xff;
udhcp_find_option tests the code as follows:
while (opt_list && opt_list->data[OPT_CODE] < code)
...
if (opt_list && opt_list->data[OPT_CODE] == code)
So yes, OPT_CODE and D6_OPT_CODE are both 0, but the D6_OPT_CLIENTID =
1 value means that the 1 is in the seconds byte, and udhcp_find_option
is only looking at the first byte, So the send_d6_release can never
find it the created option.
function old new delta
udhcp_find_option 28 53 +25
attach_option 276 284 +8
udhcpc6_main 2602 2607 +5
perform_d6_release 262 267 +5
udhcpd_main 1518 1520 +2
udhcpc_main 2542 2544 +2
add_serverid_and_clientid_options 46 48 +2
------------------------------------------------------------------------------
(add/remove: 0/0 grow/shrink: 7/0 up/down: 49/0) Total: 49 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
After more testing, (1) I'm more sure it is indeed correct, and
(2) it is a significant speedup - we do a lot of those multiplications.
function old new delta
sp_512to256_mont_reduce_8 191 223 +32
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Change sp_256to512z_mont_{mul,sqr}_8 to not require/zero upper 256 bits.
There is only one place where we actually used that (and that's why there
used to be zeroing memset of top half!). Fix up that place.
As a bonus, 256x256->512 multiply no longer needs to care for
"r overlaps a or b" case.
This shrinks sp_point structure as well, not just temporaries.
function old new delta
sp_256to512z_mont_mul_8 150 - -150
sp_256_mont_mul_8 - 147 +147
sp_256to512z_mont_sqr_8 7 - -7
sp_256_mont_sqr_8 - 7 +7
sp_256_ecc_mulmod_8 494 543 +49
sp_512to256_mont_reduce_8 243 249 +6
sp_256_point_from_bin2x32 73 70 -3
sp_256_proj_point_dbl_8 353 345 -8
sp_256_proj_point_add_8 544 499 -45
------------------------------------------------------------------------------
(add/remove: 2/2 grow/shrink: 2/3 up/down: 209/-213) Total: -4 bytes
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Denys Vlasenko
Miroslav Lichvar
Samuel Thibault
Henrique Rodrigues
Ildar Shaimordanov