| .. |
|
TARGET_MTB_MTS_DRAGONFLY
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_MTS_DRAGONFLY_F411RE
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_MTS_MDOT_F405RG
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_MTS_MDOT_F411RE
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_STM32F401xC
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_STM32F401xE
|
Add support for STEVAL-3DP001V1 board, which has an STM32F401VE chip. This support is based on the NUCLEO-F401RE board. Which has the same amount of flash/ram but less pins available on the chip.
|
2018-03-14 14:48:10 -05:00 |
|
TARGET_STM32F407xG
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_STM32F410xB
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_STM32F411xE
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_STM32F412xG
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_STM32F413xH
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_STM32F429xI
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_STM32F437xG
|
Call i2c_init() before i2c_frequency() (since i2c_frequency() requires the object to be set up) and zero the I2C object before giving it to i2c_init() as i2_init() has to set up a default frequency for its timeouts to work and it will only do this if the hz field in the object was zero to begin with (otherwise you end up with a random but usually very large indeed timeout).
|
2018-03-14 14:48:09 -05:00 |
|
TARGET_STM32F439xI
|
ODIN MTB LEDs Fix
|
2018-03-14 14:48:09 -05:00 |
|
TARGET_STM32F446xE
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
TARGET_STM32F469xI
|
STM32F4 Cube v1.19.0 update : ST CMSIS files
|
2018-02-23 17:08:30 -06:00 |
|
device
|
Add support for STEVAL-3DP001V1 board, which has an STM32F401VE chip. This support is based on the NUCLEO-F401RE board. Which has the same amount of flash/ram but less pins available on the chip.
|
2018-03-14 14:48:10 -05:00 |
|
analogin_device.c
|
STM32: fix linker error with adc_read()
|
2017-11-17 13:50:59 +01:00 |
|
analogout_device.c
|
fix init struct analogout
|
2017-10-05 16:35:05 +02:00 |
|
can_device.h
|
STM32 CAN3: remove test of CAN_2 and CAN_3
|
2017-12-20 16:05:43 +00:00 |
|
common_objects.h
|
STM32: CAN: restore registers after can_reset
|
2017-09-05 10:27:21 +02:00 |
|
device.h
|
restructure - Moved targets out to top level
|
2016-09-30 19:18:09 -05:00 |
|
flash_api.c
|
STM32: remove trailing white spaces
|
2017-11-08 10:28:46 +01:00 |
|
gpio_irq_device.c
|
STM32: move pin_lines_desc to c file
|
2017-02-16 19:34:11 +01:00 |
|
gpio_irq_device.h
|
STM32: move pin_lines_desc to c file
|
2017-02-16 19:34:11 +01:00 |
|
hal_init_pre.c
|
STM32F4 Cube v1.19.0 update : ST HAL files
|
2018-02-23 17:08:30 -06:00 |
|
i2c_device.h
|
[STM32] Make most of the I2C code into a common file
|
2016-11-30 08:23:13 +01:00 |
|
pin_device.h
|
stm32: use default in switch case
|
2017-02-16 19:34:01 +01:00 |
|
pwmout_device.c
|
STM32: move pwmout device tables to C file
|
2017-02-27 17:07:01 +01:00 |
|
pwmout_device.h
|
STM32: move pwmout device tables to C file
|
2017-02-27 17:07:01 +01:00 |
|
serial_device.c
|
STM32 serial: use uart_name in serial_irq_set function for F4
|
2018-02-09 14:18:42 +00:00 |
|
spi_api.c
|
[STM32] Deploy SPI_ASYNCH to all family
|
2016-10-13 14:18:21 +02:00 |
|
spi_device.h
|
STM32 SPI specific mode for higher performance
|
2017-06-16 10:23:48 +02:00 |
99d673efd4