mirror of https://github.com/ARMmbed/mbed-os.git
170 lines
7.7 KiB
C
170 lines
7.7 KiB
C
/* USER CODE BEGIN Header */
|
|
/**
|
|
******************************************************************************
|
|
* File Name : hw_conf.h
|
|
* Description : Hardware configuration file for BLE
|
|
* middleWare.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2019 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
*/
|
|
|
|
/* USER CODE END Header */
|
|
|
|
/* Define to prevent recursive inclusion -------------------------------------*/
|
|
#ifndef HW_CONF_H
|
|
#define HW_CONF_H
|
|
|
|
/******************************************************************************
|
|
* Semaphores
|
|
* THIS SHALL NO BE CHANGED AS THESE SEMAPHORES ARE USED AS WELL ON THE CM0+
|
|
*****************************************************************************/
|
|
/* Index of the semaphore used to manage the entry Stop Mode procedure */
|
|
#define CFG_HW_ENTRY_STOP_MODE_SEMID 4
|
|
|
|
/* Index of the semaphore used to access the RCC */
|
|
#define CFG_HW_RCC_SEMID 3
|
|
|
|
/* Index of the semaphore used to access the FLASH */
|
|
#define CFG_HW_FLASH_SEMID 2
|
|
|
|
/* Index of the semaphore used to access the PKA */
|
|
#define CFG_HW_PKA_SEMID 1
|
|
|
|
/* Index of the semaphore used to access the RNG */
|
|
#define CFG_HW_RNG_SEMID 0
|
|
|
|
/******************************************************************************
|
|
* HW TIMER SERVER
|
|
*****************************************************************************/
|
|
/**
|
|
* The user may define the maximum number of virtual timers supported.
|
|
* It shall not exceed 255
|
|
*/
|
|
#define CFG_HW_TS_MAX_NBR_CONCURRENT_TIMER 6
|
|
|
|
/**
|
|
* The user may define the priority in the NVIC of the RTC_WKUP interrupt handler that is used to manage the
|
|
* wakeup timer.
|
|
* This setting is the preemptpriority part of the NVIC.
|
|
*/
|
|
#define CFG_HW_TS_NVIC_RTC_WAKEUP_IT_PREEMPTPRIO 3
|
|
|
|
/**
|
|
* The user may define the priority in the NVIC of the RTC_WKUP interrupt handler that is used to manage the
|
|
* wakeup timer.
|
|
* This setting is the subpriority part of the NVIC. It does not exist on all processors. When it is not supported
|
|
* on the CPU, the setting is ignored
|
|
*/
|
|
#define CFG_HW_TS_NVIC_RTC_WAKEUP_IT_SUBPRIO 0
|
|
|
|
/**
|
|
* Define a critical section in the Timer server
|
|
* The Timer server does not support the API to be nested
|
|
* The Application shall either:
|
|
* a) Ensure this will never happen
|
|
* b) Define the critical section
|
|
* The default implementations is masking all interrupts using the PRIMASK bit
|
|
* The TimerServer driver uses critical sections to avoid context corruption. This is achieved with the macro
|
|
* TIMER_ENTER_CRITICAL_SECTION and TIMER_EXIT_CRITICAL_SECTION. When CFG_HW_TS_USE_PRIMASK_AS_CRITICAL_SECTION is set
|
|
* to 1, all STM32 interrupts are masked with the PRIMASK bit of the CortexM CPU. It is possible to use the BASEPRI
|
|
* register of the CortexM CPU to keep allowed some interrupts with high priority. In that case, the user shall
|
|
* re-implement TIMER_ENTER_CRITICAL_SECTION and TIMER_EXIT_CRITICAL_SECTION and shall make sure that no TimerServer
|
|
* API are called when the TIMER critical section is entered
|
|
*/
|
|
#define CFG_HW_TS_USE_PRIMASK_AS_CRITICAL_SECTION 1
|
|
|
|
/**
|
|
* This value shall reflect the maximum delay there could be in the application between the time the RTC interrupt
|
|
* is generated by the Hardware and the time when the RTC interrupt handler is called. This time is measured in
|
|
* number of RTCCLK ticks.
|
|
* A relaxed timing would be 10ms
|
|
* When the value is too short, the timerserver will not be able to count properly and all timeout may be random.
|
|
* When the value is too long, the device may wake up more often than the most optimal configuration. However, the
|
|
* impact on power consumption would be marginal (unless the value selected is extremely too long). It is strongly
|
|
* recommended to select a value large enough to make sure it is not too short to ensure reliability of the system
|
|
* as this will have marginal impact on low power mode
|
|
*/
|
|
#define CFG_HW_TS_RTC_HANDLER_MAX_DELAY ( 10 * (LSI_VALUE/1000) )
|
|
|
|
/**
|
|
* Interrupt ID in the NVIC of the RTC Wakeup interrupt handler
|
|
* It shall be type of IRQn_Type
|
|
*/
|
|
#define CFG_HW_TS_RTC_WAKEUP_HANDLER_ID RTC_WKUP_IRQn
|
|
|
|
/******************************************************************************
|
|
* HW UART
|
|
*****************************************************************************/
|
|
|
|
#define CFG_HW_LPUART1_ENABLED 0
|
|
#define CFG_HW_LPUART1_DMA_TX_SUPPORTED 0
|
|
|
|
#define CFG_HW_USART1_ENABLED 1
|
|
#define CFG_HW_USART1_DMA_TX_SUPPORTED 1
|
|
|
|
/**
|
|
* UART1
|
|
*/
|
|
#define CFG_HW_USART1_PREEMPTPRIORITY 0x0F
|
|
#define CFG_HW_USART1_SUBPRIORITY 0
|
|
|
|
/** < The application shall check the selected source clock is enable */
|
|
#define CFG_HW_USART1_SOURCE_CLOCK RCC_USART1CLKSOURCE_SYSCLK
|
|
|
|
#define CFG_HW_USART1_BAUDRATE 115200
|
|
#define CFG_HW_USART1_WORDLENGTH UART_WORDLENGTH_8B
|
|
#define CFG_HW_USART1_STOPBITS UART_STOPBITS_1
|
|
#define CFG_HW_USART1_PARITY UART_PARITY_NONE
|
|
#define CFG_HW_USART1_HWFLOWCTL UART_HWCONTROL_NONE
|
|
#define CFG_HW_USART1_MODE UART_MODE_TX_RX
|
|
#define CFG_HW_USART1_ADVFEATUREINIT UART_ADVFEATURE_NO_INIT
|
|
#define CFG_HW_USART1_OVERSAMPLING UART_OVERSAMPLING_8
|
|
|
|
#define CFG_HW_USART1_TX_PORT_CLK_ENABLE __HAL_RCC_GPIOB_CLK_ENABLE
|
|
#define CFG_HW_USART1_TX_PORT GPIOB
|
|
#define CFG_HW_USART1_TX_PIN GPIO_PIN_6
|
|
#define CFG_HW_USART1_TX_MODE GPIO_MODE_AF_PP
|
|
#define CFG_HW_USART1_TX_PULL GPIO_NOPULL
|
|
#define CFG_HW_USART1_TX_SPEED GPIO_SPEED_FREQ_VERY_HIGH
|
|
#define CFG_HW_USART1_TX_ALTERNATE GPIO_AF7_USART1
|
|
|
|
#define CFG_HW_USART1_RX_PORT_CLK_ENABLE __HAL_RCC_GPIOB_CLK_ENABLE
|
|
#define CFG_HW_USART1_RX_PORT GPIOB
|
|
#define CFG_HW_USART1_RX_PIN GPIO_PIN_7
|
|
#define CFG_HW_USART1_RX_MODE GPIO_MODE_AF_PP
|
|
#define CFG_HW_USART1_RX_PULL GPIO_NOPULL
|
|
#define CFG_HW_USART1_RX_SPEED GPIO_SPEED_FREQ_VERY_HIGH
|
|
#define CFG_HW_USART1_RX_ALTERNATE GPIO_AF7_USART1
|
|
|
|
#define CFG_HW_USART1_CTS_PORT_CLK_ENABLE __HAL_RCC_GPIOA_CLK_ENABLE
|
|
#define CFG_HW_USART1_CTS_PORT GPIOA
|
|
#define CFG_HW_USART1_CTS_PIN GPIO_PIN_11
|
|
#define CFG_HW_USART1_CTS_MODE GPIO_MODE_AF_PP
|
|
#define CFG_HW_USART1_CTS_PULL GPIO_PULLDOWN
|
|
#define CFG_HW_USART1_CTS_SPEED GPIO_SPEED_FREQ_VERY_HIGH
|
|
#define CFG_HW_USART1_CTS_ALTERNATE GPIO_AF7_USART1
|
|
|
|
#define CFG_HW_USART1_DMA_TX_PREEMPTPRIORITY 0x0F
|
|
#define CFG_HW_USART1_DMA_TX_SUBPRIORITY 0
|
|
|
|
#define CFG_HW_USART1_DMAMUX_CLK_ENABLE __HAL_RCC_DMAMUX1_CLK_ENABLE
|
|
#define CFG_HW_USART1_DMA_CLK_ENABLE __HAL_RCC_DMA2_CLK_ENABLE
|
|
#define CFG_HW_USART1_TX_DMA_REQ DMA_REQUEST_USART1_TX
|
|
#define CFG_HW_USART1_TX_DMA_CHANNEL DMA2_CHANNEL_4
|
|
#define CFG_HW_USART1_TX_DMA_IRQn DMA2_CHANNEL_4_IRQn
|
|
#define CFG_HW_USART1_DMA_TX_IRQHandler DMA2_CHANNEL_4_IRQHandler
|
|
|
|
#endif /*HW_CONF_H */
|
|
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|