/*
 * Copyright (c) 2018-2019 ARM Limited. All rights reserved.
 * SPDX-License-Identifier: Apache-2.0
 * Licensed under the Apache License, Version 2.0 (the License); you may
 * not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 * http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an AS IS BASIS, WITHOUT
 * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

#ifndef WISUNINTERFACE_H
#define WISUNINTERFACE_H

#include "MeshInterfaceNanostack.h"

/** Wi-SUN mesh network interface class
 *
 * Configure Nanostack to use Wi-SUN protocol.
 */
class WisunInterface : public MeshInterfaceNanostack {
public:

    /** Create an uninitialized WisunInterface
     *
     *  Must initialize to initialize the mesh on a phy.
     */
    WisunInterface() { }

    /** Create an initialized WisunInterface
     *
     */
    WisunInterface(NanostackRfPhy *phy) : MeshInterfaceNanostack(phy) { }

    /**
     * \brief Set Wi-SUN network name.
     *
     * Function stores new network name to mbed-mesh-api and uses it when connect() is called next time.
     * If device is already connected to the Wi-SUN network then device will restart network discovery after
     * changing the network name.
     *
     * Function overwrites network name defined by Mbed OS configuration.
     *
     * \param network_name Network name as NUL terminated string. Can't exceed 32 characters and can't be NULL.
     * \return MESH_ERROR_NONE on success.
     * \return MESH_ERROR_UNKNOWN in case of failure.
     * */
    mesh_error_t set_network_name(char *network_name);

    /**
     * \brief Set Wi-SUN network regulatory domain, operating class and operating mode.
     *
     * Function stores new parameters to mbed-mesh-api and uses them when connect() is called next time.
     * If device is already connected to the Wi-SUN network then device will restart network discovery after
     * changing the regulatory_domain, operating_class or operating_mode.
     *
     * Function overwrites parameters defined by Mbed OS configuration.
     *
     * \param regulatory_domain Values defined in Wi-SUN PHY-specification. Use 0xff to use leave parameter unchanged.
     * \param operating_class Values defined in Wi-SUN PHY-specification.  Use 0xff to use leave parameter unchanged.
     * \param operating_mode Values defined in Wi-SUN PHY-specification. Use 0xff to use leave parameter unchanged.
     * \return MESH_ERROR_NONE on success.
     * \return MESH_ERROR_UNKNOWN in case of failure.
     * */
    mesh_error_t set_network_regulatory_domain(uint8_t regulatory_domain = 0xff, uint8_t operating_class = 0xff, uint8_t operating_mode = 0xff);

    /**
     * \brief Set own certificate and private key reference to the Wi-SUN network.
     *
     * Function can be called several times if intermediate certificates are used. Then each call to the function
     * adds a certificate reference to own certificate chain. Certificates are in bottom up order i.e. the top certificate is given last.
     *
     * Function must be called before connecting the device i.e before call to connect() method.
     * Function will not copy certificate or key, therefore addresses must remain valid.
     *
     * \param cert Certificate address.
     * \param cert_len Certificate length in bytes.
     * \param cert_key Certificate key address.
     * \param cert_key_len Certificate key length in bytes.
     * \return MESH_ERROR_NONE on success.
     * \return MESH_ERROR_STATE if method is called after calling connect().
     * \return MESH_ERROR_MEMORY in case of memory allocation failure.
     * */
    mesh_error_t set_own_certificate(uint8_t *cert, uint16_t cert_len, uint8_t *cert_key = NULL, uint16_t cert_key_len = 0);

    /**
     * \brief Remove own certificates from the Wi-SUN network.
     *
     * Function must be called before connecting the device i.e before call to connect() method.
     *
     * \return MESH_ERROR_NONE on success.
     * \return MESH_ERROR_STATE if method is called after calling connect().
     * */
    mesh_error_t remove_own_certificates(void);

    /**
     * \brief Set trusted certificate reference to the Wi-SUN network.
     *
     * Function can be called several times. Certificates are in bottom up order i.e. the top certificate is given last.
     *
     * Function must be called before connecting the device i.e before call to connect() method.
     * Function will not copy certificate, therefore addresses must remain valid.
     *
     * \param cert Certificate address.
     * \param cert_len Certificate length in bytes.
     * \return MESH_ERROR_NONE on success.
     * \return MESH_ERROR_STATE if method is called after calling connect().
     * \return MESH_ERROR_MEMORY in case of memory allocation failure.
     * */
    mesh_error_t set_trusted_certificate(uint8_t *cert, uint16_t cert_len);

    /**
     * \brief Remove trusted certificates from the Wi-SUN network.
     *
     * Function must be called before connecting the device i.e before call to connect() method.
     *
     * \return MESH_ERROR_NONE on success.
     * \return MESH_ERROR_STATE if method is called after calling connect().
     * */
    mesh_error_t remove_trusted_certificates(void);

    /**
     * \brief Get router IP address
     *
     * \param address
     * \param len
     * */
    bool getRouterIpAddress(char *address, int8_t len);
protected:
    Nanostack::WisunInterface *get_interface() const;
    virtual nsapi_error_t do_initialize();
};

#endif