/* 
 * Copyright (c) 2012 Nordic Semiconductor ASA
 * All rights reserved.
 * 
 * Redistribution and use in source and binary forms, with or without modification,
 * are permitted provided that the following conditions are met:
 * 
 *   1. Redistributions of source code must retain the above copyright notice, this list 
 *      of conditions and the following disclaimer.
 *
 *   2. Redistributions in binary form, except as embedded into a Nordic Semiconductor ASA 
 *      integrated circuit in a product or a software update for such product, must reproduce 
 *      the above copyright notice, this list of conditions and the following disclaimer in 
 *      the documentation and/or other materials provided with the distribution.
 *
 *   3. Neither the name of Nordic Semiconductor ASA nor the names of its contributors may be 
 *      used to endorse or promote products derived from this software without specific prior 
 *      written permission.
 *
 *   4. This software, with or without modification, must only be used with a 
 *      Nordic Semiconductor ASA integrated circuit.
 *
 *   5. Any software provided in binary or object form under this license must not be reverse 
 *      engineered, decompiled, modified and/or disassembled. 
 * 
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
 * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * 
 */
#ifndef PCA10000_H
#define PCA10000_H

#ifdef __cplusplus
extern "C" {
#endif

#include "nrf_gpio.h"

// Definitions for PCA10000 v2.0.0 or higher
#if 1

#define LEDS_NUMBER    3

// there is RGB LED on this board
#define LED_RGB_RED    21
#define LED_RGB_GREEN  22
#define LED_RGB_BLUE   23

#define LED_START  LED_RGB_RED
#define BSP_LED_0  LED_RGB_RED
#define BSP_LED_1  LED_RGB_GREEN
#define BSP_LED_2  LED_RGB_BLUE
#define LED_STOP   LED_RGB_BLUE

#define LEDS_ACTIVE_STATE 0

#define BUTTONS_LIST {}
#define LEDS_LIST { LED_RGB_RED, LED_RGB_GREEN, LED_RGB_BLUE }

#define LEDS_INV_MASK  LEDS_MASK

// there are no buttons on this board
#define BUTTONS_NUMBER 0

// UART pins connected to J-Link
#define RX_PIN_NUMBER  11
#define TX_PIN_NUMBER  9
#define CTS_PIN_NUMBER 10
#define RTS_PIN_NUMBER 8
#define HWFC           true

// Definitions for PCA10000 v1.0
#else

#define RX_PIN_NUMBER  3
#define TX_PIN_NUMBER  1
#define CTS_PIN_NUMBER 2
#define RTS_PIN_NUMBER 0
#define HWFC           true

#endif

// Low frequency clock source to be used by the SoftDevice
#define NRF_CLOCK_LFCLKSRC      {.source        = NRF_CLOCK_LF_SRC_XTAL,            \
                                 .rc_ctiv       = 0,                                \
                                 .rc_temp_ctiv  = 0,                                \
                                 .xtal_accuracy = NRF_CLOCK_LF_XTAL_ACCURACY_20_PPM}

#ifdef __cplusplus
}
#endif

#endif