1. aes.h/des.h/sha1.h/sha256.h/sha512.h includes config.h before aes_alt.h/des_alt.h/sha1_alt.h/sha256_alt.h/sha512_alt.h.
2. aes_alt.h/des_alt.h/sha1_alt.h/sha256_alt.h/sha512_alt.h should not be included in any other location.
3. Just include aes.h/des.h/sha1.h/sha256.h/sha512.h in aes_alt.c/des_alt.c/sha1_alt.c/sha256_alt.c/sha512_alt.c.
1. aes.h/des.h/sha1.h/sha256.h/sha512.h includes config.h before aes_alt.h/des_alt.h/sha1_alt.h/sha256_alt.h/sha512_alt.h.
2. aes_alt.h/des_alt.h/sha1_alt.h/sha256_alt.h/sha512_alt.h should not be included in any other location.
3. Just include aes.h/des.h/sha1.h/sha256.h/sha512.h in aes_alt.c/des_alt.c/sha1_alt.c/sha256_alt.c/sha512_alt.c.
When specifying a full channel mask in .lib and setting the channel
to zero, device does proper channel scan.
For Thread, channel must be specified for router.
Sleepy devices don't respect the channel settings but do a full channel
scan at the start.
+ Modified the channel mask print to use hex.
The K64F Ethernet driver installs an interrupt handler that sets thread
flags, and this could be called before the thread was initialised, so it
would use a NULL thread ID.
This triggers an RTX error-checking trap in debug builds, and could also
lead to other problems with received packets not being processed.
Adjusted so the RX interrupt handler does nothing if the thread isn't
initialised yet, and manually trigger a RX event flag after initialising
the thread in case any interrupts were ignored.
An alternative would have been to implement eth_arch_enable_interrupts,
but this mechanism is not present in the EMAC world - drivers will have
to start returning interrupts in their power up.
Fixes#5680
d0a2597 Fix IAR compilation error with NUCLEO_F401RE (#86)
674a465 Delete transaction if message is non-confirmable (#83)
git-subtree-dir: features/nanostack/FEATURE_NANOSTACK/coap-service
git-subtree-split: d0a25979f8143334c86e422fd358f895bde2ad87
ExhaustibleBlockDevice.h
- Fix typos for consistent spelling.
ObservingBlockDevice.h
- Fix typos for consistent spelling.
ReadOnlyBlockDevice.h
- Fix typos for consistent spelling.
README.md
- Fix typos, mostly for branding.
DESIGN.md
- Make minor changes for consistent spelling and precise language.
SPEC.md
- Make minor changes for consistent spelling and precise language.
README.md
- Make minor changes for consistent spelling and precise language.
Not all devices have enough heap to fit a simulated heap block device,
however using a simulated heap block device is preferred if available
(reduced flash wear, faster testing).
Added MBED_TEST_SIM_BLOCKDEVICE for tests that only need a simulated
block device (wear_leveling + resilience), and added support for targets
that are known to have enough heap.
GattServer::write on Nordic's targets use sd_ble_gatts_hvx to send an
handle value Notification or Indication; This function can fail if the
connection handle is invalid or if Updates are not enabled for this
connection.
This patch workaround those limitations.
Need to avoid a TX packet error from messing up the TX FIFO. Since this API will return busy if a packet is in transmission anyways, this is acceptable.
Unfortunately there are several issues colluding to force the timeout
this high.
1. The tests push littlefs to the limits of how many errors it can
handle before failing. As a side effect this causes a massive amount
of debug/warn/error logging about the situation.
2. The logging can't be turned off for specific tests. Note: This might
change with the introduction of test-configs.
3. Logging is fixed to a baud rate of 9600. Previous testing was carried
out with a baud rate of 115200, which is the reason for the original
timeout.
Previously, send() was somewhat soft - it only ever made one send
call to the underlying stack, so it would typically take as much data
as would fit in the buffer, and only block if it was unable to write
anything.
This is not the intent of a POSIX socket/filehandle write. It should try
to send everything if blocking, and only send less if interrupted by a
signal:
- If the O_NONBLOCK flag is clear, write() shall block the calling
thread until the data can be accepted.
- If the O_NONBLOCK flag is set, write() shall not block the thread.
If some data can be written without blocking the thread, write()
shall write what it can and return the number of bytes written.
Otherwise, it shall return -1 and set errno to [EAGAIN].
This "send all" behaviour is of slightly limited usefulness in POSIX, as
you still usually have to worry about the interruption possibility:
- If write() is interrupted by a signal before it writes any data, it
shall return -1 with errno set to [EINTR].
- If write() is interrupted by a signal after it successfully writes
some data, it shall return the number of bytes written.
But as mbed OS does not have the possibility of signal interruption, if we
strengthen send to write everything, we can make applications' lives
easier - they can just do "send(large amount)" confident that it will
all go in one call (if no errors).
So, rework to make multiple sends to the underlying stack, blocking as
necessary, until all data is written.
This change does not apply to recv(), which is correct in only blocking until
some data is available:
- If O_NONBLOCK is set, read() shall return -1 and set errno to [EAGAIN].
- If O_NONBLOCK is clear, read() shall block the calling thread until some
data becomes available.
- The use of the O_NONBLOCK flag has no effect if there is some data
available.
ccli8
Ashok Rao
bcostm
Seppo Takalo
Kevin Bracey
Prashant Ravi
Ryan Kurte
jeromecoutant
Steven Cooreman
Vincent Coubard
Mika Leppänen
Arto Kinnunen
Martin Kojtal
Christopher Haster
Amanda Butler
Mahadevan Mahesh
Jimmy Brisson
Deepika