As the `psa` library is not included in the baremetal profile, perform
a TFM system reset only if the `psa` library is included in
the build otherwise perform a normal CMSIS system reset.
ARM Compiler 6.13 testing revealed linker errors pointing out
conflicting use of `__user_setup_stackheap` and
`__user_initial_stackheap` in some targets. Remove the unwanted
`__user_initial_stackheap` from the targets - the setup is
centralised in the common platform code.
Looking into this, a number of other issues were highlighted
* Almost all targets had `__initial_sp` hardcoded in assembler,
rather than getting it from the scatter file. This was behind
issue #11313. Fix this generally.
* A few targets' `__initial_sp` values did not match the scatter
file layout, in some cases meaning they were overlapping heap
space. They now all use the area reserved in the scatter file.
If any problems are seen, then there is an error in the
scatter file.
* A number of targets were reserving unneeded space for heap and
stack in their startup assembler, on top of the space reserved in
the scatter file, so wasting a few K. A couple were using that
space for the stack, rather than the space in the scatter file.
To clarify expected behaviour:
* Each scatter file contains empty regions `ARM_LIB_HEAP` and
`ARM_LIB_STACK` to reserve space. `ARM_LIB_STACK` is sized
by the macro `MBED_BOOT_STACK_SIZE`, which is set by the tools.
`ARM_LIB_HEAP` is generally the space left over after static
RAM and stack.
* The address of the end of `ARM_LIB_STACK` is written into the
vector table and on reset the CPU sets MSP to that address.
* The common platform code in Mbed OS provides `__user_setup_stackheap`
for the ARM library. The ARM library calls this during startup, and
it calls `__mbed_user_setup_stackheap`.
* The default weak definition of `__mbed_user_setup_stackheap` does not
modify SP, so we remain on the boot stack, and the heap is set to
the region described by `ARM_LIB_HEAP`. If `ARM_LIB_HEAP` doesn't
exist, then the heap is the space from the end of the used data in
`RW_IRAM1` to the start of `ARM_LIB_STACK`.
* Targets can override `__mbed_user_setup_stackheap` if they want.
Currently only Renesas (ARMv7-A class) devices do.
* If microlib is in use, then it doesn't call `__user_setup_stackheap`.
Instead it just finds and uses `ARM_LIB_STACK` and `ARM_LIB_HEAP`
itself.
We should not block in case the UART is busy transmitting. The
API has been updated to check the status of all UART's and return
1 in case any of them is busy transmitting.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The code checks if any of the UART's is still transmitting.
If so then prevent from entering deepsleep
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
1. Use the updated API's provided by the SMC driver
2. Wait till debug UART has finished transmitting data
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
1. Update to handle 12-bit resolution
2. Properly handle the pin configuration
3. Update the pin setup to handle the ADC B channel
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The IRQ disable was always disabling both rising
and falling edges of the interrupt thereby causing
failures in cases when one of the two should stay enabled.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
adbridge
Pawel Zarembski
toyowata
Qinghao Shi
Martin Kojtal
Hugues Kamba
Przemyslaw Stekiel
Maciej Bocianski
Kevin Bracey
int_szyk
Mahesh Mahadevan
Jaeden Amero
Chris Snow
David Rauschenbach
Seppo Takalo