Previously it was 2 pages - 1kB - which isn't sufficient to store
Reserved Area and Master Record. Reserved are requires one page and Master
Record takes two pages. With 512B page size and having two areas, active and
inactive, the minimum size requirement becomes 2 areas * 3 pages = 3kB. That
isn't enough to store any keys though.
* Make mbed_error use bitwise MbedCRC call rather than local
implementation.
* Remove use of POLY_32BIT_REV_ANSI from LittleFS.
* Move some MbedCRC instances closer to use - construction cost is
trivial, and visibility aids compiler optimisation.
The addition of trace logging during greentea tests pushes the multithreaded
read-write test beyond the limits of the stack it allocates for its threads.
The increase of 128 bytes was chosen by experimentation.
_inc_set_handle is new'd in SecureStore::init(), then its members are
referenced in various functions without being explicitly initialized
first. These pre-existing values can confuse the SecureStore's internal
state and cause various undesired behavior.
* Change MBED_ASSERTS() to return valid error code, so that
checks are not bypassed on release builds.
* Fix starting address calculations so that "addr" parameter is always
relative to SlicingDevice and "_start" is only added when calls to
underlying storage block is made.
* Bypass BlockDevice:is_valid_*() to underlying block device.
Slicingblockdevice was just verifying addresses independently, without
verifying those from underlying block storage.
* Refactor some headers to use relative path from Mbed OS root.
* Refactor some data types to compile on 64bit machines.
* Refactor some debug traces to use mbed_trace.
- Enable FLASHIAP for all H7 boards
- Use "TDB_INTERNAL" for all H7 boards
- Define specific internal_base_address only for DISCO_H747I_CM7
(default address is the end of FLASH which is correct for other H7 boards)
- Correct GetSectorBase function with Dual Bank information
As of 722628be02, the "remainder" configuration
also uses the default location near the end of flash. Which makes the two tests
nearly identical with the exception that the "last two sectors" test correctly
handles parts with a low (possibly 1:1) erase size to program size ratio.
Therefore, change the "remainder" test to instead be a "default" test that uses
the tdb_internal_address/size values, so that it
a.) tests something meaningfully different and
b.) tests using the custom TDB address/size values if they are provided.
c.) functions correctly on devices where the default sector-based size computation
does not work (e.g. because of the low erase size to program size ratio)
and therefore a custom location and size has been specified.
The is_conf_tdb_internal variable is unused and therefore removed.
The QSPI spec allows alt to be any size that is a multiple of the
number of data lines. For example, Micron's N25Q128A uses only a
single alt cycle for all read modes (1, 2, or 4 bits depending on
how many data lines are in use).
Return value was ignored, and TDBStore:init() ended up in a
MBED_ERROR() phase after that.
TDBStore API was limited to allow returning of only two separate
errors, which may end up hiding the actual return value. Change
the documentation slightly to allow returning of original error
code from the underlying block device.
Fixes#11591
The default computation assumes that a flash sector is several times
larger than a flash page. On PSoC 6 targets this is not the case
(the two values are the same) so the computed size is too small.
This is a similar change to 1b1f14d36b,
but for devices which implement TDB in internal storage.
When flashing a binary STLink won't skip writing padding which happens
to be the same value as flash's erase value. STM32L4 based targets
have an additional 8-bit of embedded ECC for each 64-bit word of data.
The initial value, when a sector is erased, for the ECC bits is 0xFF.
When you write the erase value to a given address these bits gets
modified to something different due to the ECC algoritm in use. The
visible bits are intact but difference in ECC value prevents flipping
any 1's to 0's. Only way to proceed is to erase the whole sector.
Martin Kojtal
Veijo Pesonen
Seppo Takalo
amq
Kevin Bracey
Kyle Kearney
Matthew Macovsky
RAJKUMAR KANAGARAJ
jeromecoutant
Janne Kiiskila
midd
Anna Bridge
Christopher Haster
Hugues Kamba
Roman Okhrimenko
Vairamuthu Ramasamy
Jammu Kekkonen