1. Add the IVT header to the binary as this is required for boot up
This was earlier added by the DAPLink firmware. As it is no longer
handled in DAPLink, the header needs to be added inside mbed.
2. Update drivers
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
1. Define RTX_NO_MULTITHREAD_CLIB to provide Mbed-specific multi-thread support for ARM/ARMC6
2. All overridden _mutex_xxx functions are declared with __USED to avoid excluded by linker
NOTE: Microlib doesn't support multi-thread
New changes to Mbed error reporting in 5.9 exposed bug in SPI
driver where an instance was uninitialized twice which triggered
an ASSERT.
This fix keeps track of which instance has been initialized and
only calls uninit when it is safe.
Increase timeout for netsocket TCP and UDP tests. Old timeout
(240 seconds) was not enough for slower devices to complete the
tests.
Accept error codes NSAPI_ERROR_CONNECTION_TIMEOUT and
NSAPI_ERROR_NO_CONNECTION when running test wifi_connect_secure_fail
Set the second highest user level, leaving the highest for UART (we are having constant overflows) and two levels below for everything else.
This should increase the timer accuracy.
RTC counter is 24-bit. Upper layer handles counter size and wraps ticks count when interrupt is to be fired before passing it to common_rtc_set_interrupt(), but for consistency and safety reasons we can wrap it again in the NRF driver.
There are cases where a call hal_deepsleep would overflow the idle task
stack, especially in developper or debug profile.
In order to avoid this case, we split ForceClockOutofDeepSleep
into two separate functions the two structure RCC_ClkInitStruct and
RCC_OscInitStruct are not allocated at the same time.
Currently, if all TX descriptors are in use and IP stack calls K64F/K66F
ethernet driver link out, link out drops the packet. Added 10ms delay
to link out to wait for a descriptor to become available before dropping
the packet.
Changed K64F/K66F power up to return without waiting for link up i.e. for
the ethernet cable to be connected. This is needed for non-blocking use
of driver e.g. for using the driver from event queue.
By default IAR generates "transfer of control bypasses initialization"
warnings for C code - it's a legal construct that frequently occurs when
doing Linux-style "goto error". Many occurrences in Nanostack.
Suppress the warning for C only, to align with GCC and ARMCC. Have to
take care not to put it in the "common" section, as this would suppress
it for C++, where it actually is illegal.
If the automatic uplink is sent directly the call-stack becomes larger than 1K
which may cause serious problems in debug builds. Just to have a respite between
RX and TX we queue an event for the automatic uplink rather than directly undergoing
an automatic uplink.
RX1 and 2 delays needed to be more precise and aggregate tx time was
drifiting because of timing difference between actual tx interrupt and
our processing of that interrupt ever so slightly.
We now take a timestamp of the tx interrupt and take a time diff while
instantiating delay timers. The timestamp is then used to update the aggregate
tx time.
Two new methods are introduced in the LoRaMac class which provide current
timing and current receive slot. These functions are used by LoRaWANStack
for its processing.
Mahesh Mahadevan
paul-szczepanek-arm
Amanda Butler
Teppo Järvelin
aqib nasim
ccli8
Cruz Monrreal II
Melvin van den berg
Marcus Chang
Juha Ylinen
Martin Kojtal
Przemyslaw Stekiel
Qinghao Shi
Kari Haapalehto
ben
Laurent MEUNIER
deepikabhavnani
bcostm
Mika Leppänen
Seppo Takalo
Kevin Bracey
Jimmy Brisson
Hasnain Virk