* Fix for calculating CAN timing settings.
NominalPrescaler value needs to be as high as possible to ensure a good approximation of the target CAN speed.
Previous usage of macro IS_FDCAN_DATA_TSEG1 refers to (unsupported by Mbed ) FDCAN CAN controller settings and leads to too low prescaler values.
Usage Macro IS_FDCAN_NOMINAL_TSEG1 yields optimum results.
See also correct macro usage in line #158.
* Add complete support of DHCP relay interface ID option
RFC3315 specifies the following: "The relay agent MAY send the Interface-id
option to identify the interface on which the client message was received.
If a relay agent receives a Relay-reply message with an Interface-id
option, the relay agent relays the message to the client through the
interface identified by the option."
The current implementation of the DHCP relay reply handling, the interface
ID field from the server response is ignored. Managing the interface ID
is very important especially as DHCP requests/replies use link-local
addresses. The consequence of this is that the interface must always be
specified because the routing layer cannot guess the correct interface.
Moreover, Mbed provides a mechanism to enable/disable the interface ID
option on a DHCP relay instance, so it is important to fully support it.
The reason why this issue has not been discoverd until now is that the DHCP
relay is mainly used on systems that use only one interface (such as Wi-SUN
routers). By default, when no interface ID is specified for the socket, the
latter will choose 6loWPAN interface by default. This means that if two
interfaces are used on the same device, the 6loWPAN interface is always
selected.
The commit adds code to retrieve the interface-id value contained within
the DHCP relay reply message and write it to a control message header
that is added to the socket message. This tells the socket which
interface to choose. If the interface-id option is not enabled on the
relay, this procedure is simply ignored.
* Support Nuvoton target NUMAKER_IOT_M467
1. Based on alpha version BSP (85564a2716548e7b6d6a79a490c6d94a24cf9bcf)
2. Continuing above, tweak BSP:
(1) Add EPWM_ConfigOutputChannel2() to enable below 1Hz and below 1% duty cycle for PWM output (m460_epwm.h/c).
(2) Add dummy RTC_WaitAccessEnable() for consistency with previous ports (m460_rtc.h).
3. Target NuMaker-M467HJ V0.1 board temporarily
4. Support Arduino UNO form factor for NUMAKER_IOT_M467 target
5. Enable export to Keil/IAR project
- tools/arm_pack_manager/index.json
- tools/export/iar/iar_definitions.json
* M467: Fix Greentea reset_reason test failure
HRESETRF is combined reset flag. Filter it out to avoid interference with reset reason check.
* M467: Support HyperRAM
1. For GCC, support multi-block .data/.bss initialization
2. HyperRAM is mapped to two regions: 0x0A000000 and 0x80000000
According to default system address map, 0x0A000000 is located at 'Code' region and 0x80000000 at 'RAM' region.
With MPU enabled on Mbed OS, 'Code' region is write-never and 'RAM' region execute-never.
0x80000000 is chosen because 'RAM' regioin is naturally for HyperRAM.
3. Configurable multi-function pins for HBI
4. To locate code/data at external HyperRAM:
- Specify __attribute__((section(".text.nu.exthyperram"))) for RO/.text/readonly section type
Invoke mbed_mpu_manager_lock_ram_execution()/mbed_mpu_manager_unlock_ram_execution() to run HyperRAM code
- Specify __attribute__((section(".data.nu.exthyperram"))) for RW/.data/readwrite section type
- Specify __attribute__((section(".bss.nu.exthyperram"))) for ZI/.bss/zeroinit section type
5. Add readme
* Config for M460 EMAC
* Add M460 EMAC driver
* Adjust M460 EMAC RX/TX buffer
* M467: Fix EMAC compile error with IAR
* M467: Support Crypto SHA/ECC H/W
1. Prepare crypto common code
2. Support list
- SHA
- ECC
NOTE: AES/RSA are to support in other works
NOTE: Compared to M487, M467's SHA supports context save & restore (DMA Cascade mode) and so no software fallback is needed.
NOTE: M467's ECC, following M487, goes partial-module replacement and it can just improve primitives e.g. point addition/doubling by 2X,
and cannot improve high level point multiplication because MbedTLS doesn’t open it.
To improve performance best, full-module replacement is needed.
NOTE: Continuing above, add support for Montgomery curve
* M467 H/W AES self-test pass
* M467 Support crypto GCM H/W
* M467: GCM support one simple mode instead of using composite GHASH & CTR MODE
* Update M467 AES-GCM to pass AWS-IoT test
* Update M467 AES-GCM for H/W gcm in-buffer creteria
* M467: Improve Crypto H/W wait helper routine
Add crypto_xxx_wait2 helper routine to replace crypto_xxx_wait for Crypto H/W control
* M467: Seed PRNG with TRNG for SCAP
According to TRM, it is suggested PRNG be seeded by TRNG on every Crypto H/W reset.
* M467: Support Crypto RSA H/W
1. Crypto RSA H/W supports 1024/2048/3072/4096 key bits. Fall back to software implementation for other key bits.
2. For decrypt, if MBEDTLS_RSA_NO_CRT isn't defined, go CRT, or normal.
3. For decrypt, when blinding (f_rng != NULL), enable SCAP mode.
4. Recover from Crypto RSA H/W failure:
(1) Enable timed-out wait to escape from RSA H/W trap
(2) On RSA H/W timeout, stop this RSA H/W operation
(3) Fall back to S/W implementation on failure
NOTE: RSA 4096 key bits can fail with default mbedtls configuration MBEDTLS_MPI_MAX_SIZE.
Enlarge MBEDTLS_MPI_MAX_SIZE to 1024 or larger if this feature is required.
NOTE: Fixed in BSP RSA driver, for non-CRT+SCAP mode, temporary buffer for MADDR6 requires to be key length plus 128 bits.
NOTE: Fixed in BSP RSA driver, DMA buffer must be 4-word aligned, or RSA H/W will trap.
* M467 Support crypto AES-CCM H/W with one-shot & cascade mode
* M467: Support Crypto ECC H/W in full-module replacement
1. Replace ecp.c full-module, and other ec modules dependent on ecp.c (ecdh.c/ecdsa.c/ecjpake.c) will improve followingly.
2. Recover from Crypto ECC H/W failure:
(1) Enable timed-out wait to escape from ECC H/W trap
(2) On ECC H/W timeout, stop this ECC H/W operation
(3) Fall back to S/W implementation on failure
3. Support Short Weierstrass curve
4. Support Montgomery curve
Montgomery curve has the form: B y^2 = x^3 + A x^2 + x
(1) In S/W impl, A is used as (A + 2) / 4. Figure out its original value for engine.
2eb06e7620/connectivity/mbedtls/include/mbedtls/ecp.h (L219-L220)
(2) In S/W impl, B is unused. Actually, B is 1 for Curve25519/Curve448 and needs to configure to engine.
2eb06e7620/connectivity/mbedtls/include/mbedtls/ecp.h (L221-L222)
(3) In S/W impl, y-coord is absent, but engine needs it. Deduce it from x-coord following:
https://tools.ietf.org/id/draft-jivsov-ecc-compact-05.htmlhttps://www.rieselprime.de/ziki/Modular_square_root
NOTE: Fix Curve448 has wrong order value
https://github.com/Mbed-TLS/mbedtls/pull/5811
* M467: Disable SCAP in RSA H/W
This is to follow designer's resolution.
* M467: support fullspeed usb device
* M467: Fix mbedtls_ecp_point_cmp() call with null argument
Guard from null argument passed to mbedtls_ecp_point_cmp() in ECC H/W port
* M467: Make mbedtls H/W port removable
Some M460 chips don't support AES/SHA/ECC/RSA H/W.
Make them removable from mbedtls H/W port through '"target.macros_remove": ["MBEDTLS_CONFIG_HW_SUPPORT"]'.
* Added TMPM4NR Platform
New Platform for Toshiba Added
* Removed UTF8 Chars
* M467: I2C: Fix potential role switch failure
Fix in i2c_do_trsn(), interrupt doesn't change back to enabled due to premature return.
* M467: Exclude UNO SPI pins from FPGA CI Test Shield test
UNO D8/D9/D10/D11/D12/D13 can wire to on-board SPI flash.
Exclude these pins from FPGA CI Test Shield test.
* M467: Adjust UART pinmap to pass FPGA CI Test Shield test
* M467: Support NuMaker-IoT-M467 board
Pinout comparison between NuMaker-M467HJ and NuMaker-IoT-M467 boards:
1. UNO are unchanged
2. LEDs are unchanged
3. Buttons are unchanged, except button names
4. NuMaker-M467HJ has HBI but NuMaker-IoT-M467 does
5. NuMaker-M467HJ doesn't have ESP8266 but NuMaker-IoT-M467 does
6. SDHC are unchanged
* Nuvoton: I2C: Fix potential role switch failure
Fix in i2c_do_trsn(), interrupt doesn't change back to enabled due to premature return.
Fix targets:
- NUMAKER_PFM_NANO130
- NUMAKER_PFM_NUC472
- NUMAKER_PFM_M453
- NUMAKER_PFM_M487/NUMAKER_IOT_M487
- NUMAKER_IOT_M252
- NUMAKER_IOT_M263A
- NU_M2354
* Update can_api.c
Modified comment as discussed.
* M467: Remove invalid UTF-8 byte sequence
* Replace MAX32660, MAX32670 I2C driver with final one in MSDK
- apply clang-format
- Fix i2c repeated start issue
Signed-off-by: Sadik.Ozer <sadik.ozer@analog.com>
* Add proper support for NUCLEO-H723ZG.
- add board specific EMAC setup to connectivity/drivers/emac/TARGET_STM/TARGET_STM32H7
- stm32h7_eth_init.c was derived from the NUCLEO-H743ZI2 code whilst comparing to the output of STM32CubeIDE
- complete board specific code in targets/TARGET_STM/TARGET_STM32H7/TARGET_STM32H723xG
- PeripheralPins.c and PinNames.h were created by targets/TARGET_STM/tools/STM32_gen_PeripheralPins.py
- ST ZIO connector pins in PinNames.h have been adapted from NUCLEO-H743ZI2
- CONSOLE_TX and CONSOLE_RX have been interchanged in PinNames.h to match the actual board layout
- startup_stm32h723xx.S was derived from startup_stm32h743xx.S
- stm32h723xg.ld was completely rewritten to match the actual MCU including:
- split heap support
- SRAM2 and SRAM4 support
- crash dump support
- proper use of DTCM as stack
- system_clock.c has been changed to support the maximal main clock speed of 550 MHz
- fix handling of HS in FS mode for the target board in targets/TARGET_STM/USBPhy_STM32.cpp
- add board definition to targets/targets.json and correct linker setup for the chip
Signed-off-by: Daniel Starke <daniel-email@gmx.net>
* Fix I2C for MCU_STM32H723xG
Add I2C configuration to MCU_STM32H723xG in target.json as suggested by @jeromecoutant.
Signed-off-by: Daniel Starke <daniel-email@gmx.net>
* Correct MAX32620 boards macro for USB library.
* Limit NUCLEO_H723ZG toolchain to GCC_ARM
Limit NUCLEO_H723ZG toolchain to GCC_ARM only.
This is the only toolchain this target has been tested with yet.
Signed-off-by: Daniel Starke <daniel-email@gmx.net>
* M2354 support FS-USBD and update TF-M for USB PHY select
* Rethink STM32 I2C v2 HAL
* Add documentation for I2C_EVENT macros
* Add some additional I2C error codes
* Added TMPM4GR Platform
New Platform for Toshiba Added
* Resolve delimeter issues for target.json
* Fix compile error on static pinmap targets
* github: Fix click version
Signed-off-by: Martin Kojtal <martin.kojtal@arm.com>
Signed-off-by: Sadik.Ozer <sadik.ozer@analog.com>
Signed-off-by: Daniel Starke <daniel-email@gmx.net>
Signed-off-by: Martin Kojtal <martin.kojtal@arm.com>
Co-authored-by: chdelfs <109847651+chdelfs@users.noreply.github.com>
Co-authored-by: YannCharbon <yann.charbon@ik.me>
Co-authored-by: Chun-Chieh Li <ccli8@nuvoton.com>
Co-authored-by: cyliangtw <cyliang@nuvoton.com>
Co-authored-by: Deepak V. Shreshti <DeepakVS@TOSHIBA-TSIP.COM>
Co-authored-by: Martin Kojtal <martin.kojtal@arm.com>
Co-authored-by: Sadik.Ozer <sadik.ozer@analog.com>
Co-authored-by: Daniel Starke <daniel-email@gmx.net>
Co-authored-by: Ahmet Alincak <Ahmet.Alincak@maximintegrated.com>
Co-authored-by: Jamie Smith <smit109@usc.edu>
Co-authored-by: Jamie Smith <jsmith@crackofdawn.onmicrosoft.com>
225a4af94f Remove files from tests folder
58d2c8fa82 Merge remote-tracking branch 'origin/release_internal' into release_external
921b4b3273 Wi-SUN FAN 1.1 dynamic MDR data request enabler
b8722e81b1 Corrected BR removing of waiting list entry when supplicant is in key storage
0d54d7ab39 Adjust trace levels (#2692)
681d9eae8d Added reset for pan id and version to BR network start
30d4fb2ed9 Renaming and cleaning ws bootstrap (#2688)
e0da19dbf0 Add Wi-SUN host configuration (#2690)
50ecc3d0f0 Refactoring Wi-SUN stack (#2686)
9d2386d484 Renamed operation mode to operating mode.
2f755bcfdb RF config resolver and some refactoring (#2683)
86c6d19e06 Fixed WS IE PCAP read operation wrong length usage.
cd3a4c2a62 Config: Remove additional HAVE_WS_ROUTER (#2684)
cdd7f2d868 Added API for configure supported Phy capability.
a00a3c0a02 Wi-SUN FAN 1.1 PCAP IE update
2d063d3b4a Moved State machine and timer functions to own files
edb8bec609 Corrected system time check function return values
85358a635b Moved Wi-SUN Bootstrap Event handling to separate device handlers
61cbdde485 MAC to support mode switch on single channel (#2678)
1006d29e4d Added storing of PAN ID to NVM in BBR
7bf0028c66 Corrected system time jump detection on BR startup
e60974d815 Split Wi-SUN bootstrap to device types
a3f341266e MAC data req: API to support mode switch (#2674)
cad5122a90 Removed automatic network size configuration (#2673)
35d313224a MAC: Callback set to resolve PHY mode ID (#2672)
0c5faca469 Added support for large system time changes (e.g. due to NTP) (#2670)
c94b306431 LFN version and LGTK Hash IE advertisment and learn
8e075119f6 Use FAN version constant instead of pure number
a5566b22b2 Channel Plan 2 validation and FAN 1.0 reject
42dba4151e Wi-Sun IE FAN 1.1 update
1d56070c24 EU channel plan ids (FAN 1.1) supported (#2668)
fc4f41fb30 Add test API empty function
37efc7ec25 Add version 1.1 basic support
e1558fbb1a Implemented mode switch PHR build and parse (#2665)
cbd8a15d31 Corrected frame counter storing threshold check
37f7ae95eb Time configuration distribution using DHCPv6 vendor data
7415bc724b Added checks for Border Router frame counter space exhaustion (#2660)
f1a65ecbe8 Mode switch PHY API (#2663)
e54231b5d4 Do not check buffer age when virtual RF driver used (#2662)
cc8c7bd38f arm_network_certificate_chain_set() returns -2 when PANA is disabled
319dd91bce Fix dubious semicolon in #define
2ff51abeca Remove extra '\n' in traces
19376c8837 Simplify array indexes
c808661836 Fix ASAN warnings about overflows in bit shifts
f998008f60 Fix use-after-free in mac_helper_coordinator_address_set()
4d04541d70 Wi-SUN header and Paylod IE element lenght future proof update.
935898badf Medium network PAN_TIMEOUT changed to 30 minutes
1af7cfeb24 Updated nanostack to be compatible with mbed TLS 3.0 (#2657)
29744e0e46 If Router Solicitation creation fails no longer tries to retry the RS right away (#2655)
2b889e92b0 Added automatic test procedure triggering during bootstrap
ed9eb0503f GTKs are removed only when fresh GTK hash is received
81ecdc24f8 Added empty function for test procedure trigger
14439b4aa9 Added support for triggering test procedures
b8a67a9e36 Update CHANGELOG.md for Nanostack 14.0.0 (#2649)
git-subtree-dir: connectivity/nanostack/sal-stack-nanostack
git-subtree-split: 225a4af94f3faf5ca3726e86bc96cdda4c99a469
4a3c5c525b Merge remote-tracking branch 'origin/release_internal' into release_external
2b8d2e1356 Do not reset radio when MAC data request timeouts (#2647)
95c506a276 Frame counters for nw keys are now stored to NVM only after send key is set (#2641)
3b3010a79b Adjusted stagger random to [min,min+max] and for small nw set the stagger value to 10 seconds
02bc33a242 Adjusted security protocol (EAP-TLS,4WH,2WH) retry timers
eb26726020 High Priority timestamp compare overflow support fix.
928723a33e FHSS WS: Initialize broadcast channel count when enabling FHSS (#2642)
6040d703c8 Updated change log
667b191223 Changed initial EAPOL-key retries from trickle to exponential backup
d925145d33 Add RTT calculation for DHCP Time calculation
0b82953567 Traceroute bug fix.
04de6e26d8 Merge pull request #2638 from PelionIoT/mbed_os_fix_ufsi_calculation
20123477c6 Fixed FHSS UFSI calculation unit tests
436f16e84f Handle timer rollover in calculate_ufsi
411cf5c7a4 coding style
d6f44218d6 Correct ufsi timing calculation
560619d85d Add network time vendor data element to DHCPv6 reply message
6d290dc3c1 System time read/write callbacks (#2637)
7905df666d Restart or remove transmission when MAC data request timeouts (#2636)
c97695cfc6 Bug fix: EAPOL parent compare fix
e283e6285c Fixed channel mask usage with OFDM configurations (#2633)
24168f891b Do not send too old packets (#2632)
dbd83be16d Fix copyrights (#2631)
7f0cffdbf7 Merge pull request #2630 from PelionIoT/use_pelion_copyright
511bd5a3ad Corrected coding style
57ec0281a8 Corrected comparison
7d853de862 When EAPOL waiting queue is full oldest entry is removed
acf580fbd0 Update copyright in changed MDNS files
933c0bbf0a Update copyright
3aeb2af77c Statistics for data request latencies (#2629)
3f7eae64ef EAPOL FHSS temp entry discover
5200b666e7 DHCP time elapsed time write fix.
0536874f64 Removed empty EAPOL-key message send after 4WH completion to nodes on relay
8a2a683aef Fixed DHCP wrong time elapsed value write.
283f2ee685 DHCPv6 update:
99be7783ec EAPOL temp neighbour update
4f9e3d12ab Adaptation layer to remove oldest packet first
20f1f6492f Added ignoring of retry messages from RADIUS server when waiting EAP-TLS
8a8b407c47 Add RSL check for ETX Calculation for RPL parent selection
c05e1da757 Fix DHCP server Uninitialized memory read
77229eefa6 Fix CPP error from domain prefix check
7e47889111 support filtering of EAPOL parents based device-min-sens configuration
618a19192c Wi-SUN Expedite forward state update
4371462d66 Fix NULL read from RPL header addition
7802c7ee97 Update CHANGELOG.md
b2c810402c CHANGELOG for Nanostack v13.0.0 (#2615)
git-subtree-dir: connectivity/nanostack/sal-stack-nanostack
git-subtree-split: 4a3c5c525b2a62c19ecfb0ac64d09bd2a7f56ceb
Aside from the core mbed-os CMake target, a number of targets have been created so they can optionally be included by application executables that require them using `target_link_libraries()`.
Co-authored-by: Martin Kojtal <martin.kojtal@arm.com>
Co-authored-by: Rajkumar Kanagaraj <rajkumar.kanagaraj@arm.com>
```
connectivity
├── netsocket
├── lwipstack
├── nanostack
│ ├── mbed_lib.json // nanostack-interface's mbed_lib.json
│ ├── include
│ │ └── nanostack // headers from features/netsocket/nanostack-interface
│ ├── source // sources from features/netsocket/nanostack-interface
│ ├── coap-service // used by Thread only - deprecate?
│ ├── mbed-mesh-api
│ ├── nanostack-hal-mbed-cmsis-rtos // HAL porting layer for Nanostack on mbed with CMSIS-RTOS
│ ├── sal-stack-nanostack
│ └── sal-stack-nanostack-eventloop
├── cellular // previously in features/cellular/framework/
├── ...
```
This PR is a part of a wider \connectivity refactoring and implements the above new directory structure for \nanostack.
Jay Sridharan
Jamie Smith
Arto Kinnunen
Arto Kinnunen
Hugues Kamba
Hugues Kamba
Ashok Rao