* Make mbed_error use bitwise MbedCRC call rather than local
implementation.
* Remove use of POLY_32BIT_REV_ANSI from LittleFS.
* Move some MbedCRC instances closer to use - construction cost is
trivial, and visibility aids compiler optimisation.
* Use compile-time detection of hardware CRC capability, so unneeded
code and tables do not go into the image.
* Add global JSON config option to allow choice between no tables,
16-entry tables or 256-entry tables for software CRC. Default set
to 16-entry, reducing ROM size from previous 256-entry.
* Allow manual override in template parameter to force software or
bitwise CRC for a particular instance.
* Micro-optimisations, particularly use of `RBIT` instruction and
optimising bitwise computation using inline assembler.
Incompatible changes:
* Remove special-case "POLY_32BIT_REV_ANSI" - users can use standard
POLY_32BIT_ANSI, which now uses the same 16-entry tables by default,
or can use hardware acceleration, which was disabled for
POLY_32BIT_REV_ANSI. MbedCRC<POLY_32BIT_ANSI, 32, CrcMode::TABLE> can
be used to force software like POLY_32BIT_REV_ANSI.
* The precomputed table for POLY_16BIT_IBM had errors - this has been
corrected, but software CRC results will be different from the previous
software calculation.
* < 8-bit CRC results are no longer are shifted up in the output value,
but placed in the lowest bits, like other sizes. This means that code
performing the SD command CRC will now need to use `(crc << 1) | 1`,
rather than `crc | 1`.
* Change "is supported" check to be a macro, so it can be done at
compile-time.
* Eliminate weird shift on 7-bit CRCs.
* Add support for 32-bit CRCs and reversals to TMPM3HQ.
These targets below just support PRNG, not real TRNG. They cannot annouce TRNG.
- NUMAKER_PFM_NUC472
- NUMAKER_PFM_M487
- NUMAKER_IOT_M487
On targets without TRNG, to run mbedtls applications which require entropy source,
there are two alternatives to TRNG:
- Custom entropy source:
Define MBEDTLS_ENTROPY_HARDWARE_ALT and provide custom mbedtls_hardware_poll(...)
- NV seed:
1. Define MBEDTLS_ENTROPY_NV_SEED
2. Define MBEDTLS_PLATFORM_NV_SEED_READ_MACRO/MBEDTLS_PLATFORM_NV_SEED_WRITE_MACRO and provide custom mbedtls_nv_seed_read(...)/mbedtls_nv_seed_write(...).
3. Don't define MBEDTLS_PSA_INJECT_ENTROPY. Meet mbedtls_psa_inject_entropy(...) undefined and then provide custom one, which must be compatible with mbedtls_nv_seed_read(...)/mbedtls_nv_seed_write(...) above.
4. For development, simulating partial provision process, inject entropy seed via mbedtls_psa_inject_entropy(...) pre-main.
The addition of trace logging during greentea tests pushes the multithreaded
read-write test beyond the limits of the stack it allocates for its threads.
The increase of 128 bytes was chosen by experimentation.
4-byte addressing has been seen to cause failures on NORDIC
boards and with Macronix memories. Suppress the attempt to enable it
on that hardware (via vendor quirks and a target check) until either
the failure cause can be fixed or a more robust suppression mechanism
is implemented.
Use a vendor id check to only perform this enable on devices which define the
second configuration register where the fast mode enable bit lives.
Change _enable_fast_mode to use the standard status register reading and writing functions
Default to 2 status registers, but update this value if necessary
during vendor quirk handling for parts (currently only Macronix)
which have one status register and two control registers. For the
purposes of QSPIFBlockDevice, these are all considered status
(or at least "status-like") registers because they are all written
via the Write Status Register instruction.
Set the custom RDCR instruction for Macronix during quirk handling.
Update reading and writing of status registers to handle a variable
number of status registers.
Introduce a separate function for handling alterations to device interaction
which are not covered by the SFDP tables and therefore require checking against
the vendor id.
QSPIFBlockDevice::_clear_block_protection() has logic to retain the
WIP and WEL bits in status register 1, but it failed to account for
the situation where the QE bit is also in status register 1.
In _sfdp_set_quad_enabled, note the status register and bit therein
for the quad enable, so that _clear_block_protection can retain it.
This function writes a "config" register to ensure that the flash part
is in high performance mode, not low-power mode. This is required at
by at least MX25R6435F in order to operate at frequencies > 33MHz
(for reference, DISCO_L475VG_IOT01A runs the QSPI interface at 80 MHz).
The config register that this writes does not appear to be covered by
the SFDP spec (JESD216D.01) so this remains the status quo of
unconditional execution, as has been done on master since #8352.
after DNS Query flooding during DNS timeout test.
DNS timeout test requires flooding device with DNS queries.
This causes problem to ESP8266 module causing it to stuck for 11 sec.
In result all following tests fails. To avoid this "smart delay" is added.
If device preforms gethostbyname correctly then tests can proceed.
Otherwise after 1 sec sleep gethostbyname is repeated until success or re-check limit (set to 15).
Thanks to this all ethernet and non ESP8266 wireless devices don't need to wait but ESP must wait.
Martin Kojtal
amq
Kimmo Vaisanen
Kevin Bracey
Chun-Chieh Li
Antti Kauppila
Kyle Kearney
Matthew Macovsky
Adam Mitchell
Giampaolo Mancini
Tymoteusz Bloch