In the reception data path, we needed to check the MCPS CONFIRMATION type
not the MCPS INDICATION type. Indication message type is for downlink message type
which can be UNCONFIRMED even if we have sent a CONFIRMED one, e.g., an ACK.
Application can give battery_level callback method what Lora stack
uses to query battery level for DevStatusReq MAC command response.
The problem was that this callback was never called.
This commit fixes this problem and if application does not set
battery_level callback at all, value 255 (= The end-device was not able to
measure the battery level.) will be returned to lora gateway.
If the frame length is not what we are expecting, it is
found to be a good practise to actually continue with what we
have received rather than aborting. As we have already demodulated
the packet and RX slots are used up, ther is not so much benefit in
dropping that packet.
While configuring RX parameters for the radio, we need to feed in
rx windows 1 and 2 parameters which are computed when we do the transmission.
We are actually setting the physical value of the data rate rather than
data rate table index and the expectation was to set the data rate index.
The asia pacific region supports custom channel planning and
downlink channel request. By virtue of a mistake, this information
was missing and hence a custom channel support was not working.
Fixes issue #6783.
There had been essentially two state machines running in our stack
which was too cumbersome and was not alligned in any symmetry.
In this work we make sure that:
* There are no callbacks from the MAC layer to Stack controller layer.
* Primitives are made local to the mac layer and are presented as
read-only to the stack controller layer.
* Interrupt handling and processing is moved to the stack controller layer.
* Reception is divided into smaller units, seperating handling of Join Accept
and normal data frames. MIC gets its own unit.
* Extraction of data and MAC commands from the payload is also being done now in
its own method.
* To ensure integrity of the stack, and sanctity of the radio payload, we copy the
radio payload buffer immediately in the rx interrupt and hoist a flag that prevents
another interrupt from happening for a short while when we are processing the previous
packet.
* If an automatic uplink is on going, we do not send a TX_DONE event to application
anymore as that is logically incorrect.
* state_controller() is the central engine for the state machine. To save code space and
memory, we are not handling each and every state in the state_controller(). Some of the states
which have no processing to be done, are explicitely set.
* For all the states who need special processing, seperate methods are added.
* Class A always run to completion to IDLE and CLass C always runs to completion as RECEIVING.
Making our LoRaWAN stack thread safe. If RTOS is not present, locks
don't do anything. ScopedLock is used to automate the lock release on
context expiry.
We went through an exercise of adding band information to
any new channel being added. Default channels were looked over.
This commits duly adds missing band information to default channels.
If Lora stack is built with incorrect mbedtls settings, crypto methods
should assert and return error value. This fixes MBED_ASSERTs to
work correctly.
band_t structure in phy parameters was not being filled in properly
and we were spilling over the array boundary for bands.
In addition to that two utility functions are added to perform safety
checking taking in the frequency and filling out band information plus
boundry value checks.
In LoRa TX power value 0 means the maximum allowed TX power and values >0
are limiting the allowed TX power to lower.
tx_config was incorrectly checking the power level and causing the maximum
TX power to be always used. Lora gateway can request node to use lower TX
power with LinkAdrReq MAC command.
In order to have smaller and better testable methods, instead of having a big
switch-case -style add_mac_command(), each MAC command is now separated to an
own method.
Bug was reported by @tpet93 and it was correctly diagnosed that channels
were not being set in the phy_params structure. This commit fixes the bug
and sets up channels correctly.
Fix compilation of compilance test and at the same time refactor compliance
test handler. Renamed mcps_request as test_request as it is only used for
compliance test. Also fixed a bug with null buffer in send_compliance_test_frame_to_mac.
- This is internal change, no functionality has been changed
- LoRaWanInterface cleaned up and code moved to LoRaMacStack
- Compliance code in LoRaMacStack moved to EOF
- Green tea tests have been run manually
- Doxygen updated accordingly
LoRA: reorder class members
This API can be used to runtime change device class.
Please note that only class A and C are supported at the moment.
Trying to set class B will return LORAWAN_STATUS_UNSUPPORTED.
Fix set_device_class documentation
fix documentation
Kimmo Vaisanen
Cruz Monrreal
Hasnain Virk
Martin Kojtal
Antti Kauppila
Kevin Bracey