For actual connections, full ConnectionParameters is used. But
as per BLE specification, Generic Access Service can display
preferred connection parameters which is a smaller subset and
ConnectionParams_t matches exactly. Thus we rename/repurpose
it to PreferredConnectionParams_t.
The callback on_connected() in ConnectionEventMonitorEventHandler
contains a parameter ConnectionParams_t which is superceded by
ConnectionParameters. Since it's not used, remove it.
Functions in Cordio for device name & appearance are currently
unused as they are both part of and dependent on deprecated
Mbed OS BLE APIs.
Nonetheless we want to keep them (and disable using macros)
so we can reintroduce them and make improvements in the future
as needed.
This is based on (and supercedes) PR #10772.
As the switches between old and new APIs do not exist anymore,
we create a function for legacy advertising set creation.
-Check pointer before writing to it. It allows application to ask
only some of the stagger values.
-Change type of data_amount in get_stagger_estimate_to_address to be
uint16_t.
Add getsockopt options NSAPI_LATENCY and NSAPI_STAGGER to read
network specific timing constraints from socket.
-NS_LATENCY returns estimated latency to given address.
-NSAPI_STAGGER returns estimated initial delay that application
should wait before transmitting data to network.
Application can use the new options to avoid network congestion by
adjusting transmission delays and retry timeouts.
Earlier if mbed-trace was disabled but debug-at enabled, some AT trace codes were still
enabled causing unnecessary code size increase.
This commit fixes the issue that AT debug trace code is enabled only when both
mbed-trace.enable and cellular.debug-at are enabled.
Reduces binary size by about ~340bytes when mbed-trace is disabled but debug-at enabled.
set_ip_address API can be used to set a static IPv4 address or IPv6 link-local
address to network stack.
This is needed for example in cellular use cases where device gets multiple IP
addresses from cellular context.
Rework TDBStore::calc_area_params so that it can handle situations where
the block device size is not an even multiple of the sector size (while
retaining its ability to handle non-uniform erase sizes).
This avoids intermittent asserts on boards where TDBStore is implemented
in internal flash, in which case the size of the block device varies
with the application size and a minor change (or a shift in optimization
level) can shift TDBStore from an odd to an even number of sectors.
Issue: The problem is that there is a race condition introduced in that the LWIP thread is relying on the
interface as it is taken down by a application thread while calling disconnect.
In disconnect api called from application context, whd_emac_wifi_link_state_changed() will refer to netif interface
structure in its callback api netif_link_irq(netif). This netif will be cleared by remove_etherent_interface().
whd_emac_wifi_link_state_changed will post message to tcpip_thread. tcpip_thread will process the message and
call the callback api netif_link_irq(netif)
Calling sequence is whd_emac_wifi_link_state_changed -> remove_etherent_interface(). Hence there is a timing issue
that netif might be cleared first before tcpip thread process the message netif_link_irq(netif)
Fix: remove_etherent_interface() will post message to tcpip thread and tcpip thread process the message delete_interface()
which will actually remove the inferface from the netif_list.
Calling sequence is whd_emac_wifi_link_state_changed() message post -> remove_etherent_interface() message post.
message processing order netif_link_irq(netif) -> delete_interface().
Since both the processing is handled in single thread, processing of message is handled sequentially.
These changes are for TFM_DUALCPU and TFM_V8M platforms.
The initialization happens after mbed-os kernel is kicked off and
when the thread is up and running.
We are initializing the following for TFM_DUALCPU platforms:
* IPC Interrupts for syncing multi-core platforms.
* NS Mailbox to receive messages.
* NS interface.
We are only initializing Non-secure interface for TFM_V8M platforms.
mbed_tfm_init() in tfm_mbed_boot.c overrides the WEAK mbed_tfm_init()
for a specific platform.
Signed-off-by: Vikas Katariya <vikas.katariya@arm.com>
Relevant modifications:
1. Support degrading QSPI0/1 to SPI4/5 for normal SPI transfer
2. Fix with BSP crypto driver API change
3. Fix with BSP PDMA driver API change
4. Make necessary modifications to pass FPGA CI Test Shield tests
5. Don't distinguish pinmap among parts e.g. M480 LG. Application users must take care.
Lingkai Dong
Martin Kojtal
Arto Kinnunen
Kimmo Vaisanen
Kyle Kearney
Arun S
MarceloSalazar
Rajkumar Kanagaraj
midd
Vikas Katariya
Ryan Morse
JojoS62
Tymoteusz Bloch
Chun-Chieh Li
Antti Kauppila
Teppo Järvelin
Hugues Kamba
jeromecoutant