Align with mainline BSP and fix relevant bugs:
1. Align with SPI module naming
(1) Remove SPI5
(2) Degrade QSPI0 to SPI4 so that it can use for standard SPI
2. Fix some code lacking GPIO H
3. Implement __PC(...) by following BSP instead of with MBED_CALLER_ADDR()
4. Add SCU_IRQHandler(). Change printf(...) with interrupt-safe error(...)
5. Other minor alignment change
Incorrect addresses only cause error return values instead of assertion.
ExhaustibleBlockDevice has working get/set_erase_cycle functions and an
array preventing programming without erase.
Fixed MBRBlockDevice partitioning function.
When reading a data block, the returned error codes from the I2C subsystem
are different from normal single byte operations. We have to verify that
the read-function for multiple bytes does return zero, because it
returns "readBytes != expectedLength".
Additionally, sync before trying to read from the eeprom as slow devices
may not yet be ready to return data, especially with low-priced ones
used with fast controllers.
1.Testing with Verizon and AT&T SIMs, PDP type is automatically set to IPV4V6.
2. Testing with AT&T IoT SIM, PDP type automatically sets to IP. It will connect
but not communicate. Setting a subsequent APN to IPV4V6 with the same APN communicates.
At these locations, psa_key_attribute variables are used without
initialisation. The function getting it (psa_get_key_attributes),
is freeing attributes->domain_parameters, which can contain random
address from the stack.
Signed-off-by: Gabor Abonyi <gabor.abonyi@arm.com>
This is a special case since targets do not provide by default GPIO pin-maps.
This extension is required for FPGA GPIO tests - if some pins have limitations (e.g. fixed pull-up) we need to skip these pins while testing.
To do that we were adding a dummy pin-map with commented out pins that can't be tested because of the limitations.
This solution is redundant and the proposition is to provide a list of restricted gpio pins if required (by default weak implementation is provided with an empty list).
This mechanism will be backward compatible, so the old method with dummy gpio pinmap will also work. The switch from dummy pin-maps to pinmap_gpio_restricted_pins() will be performed in separate commits/PRs.
Substantiation for this is that the STDIO UART peripheral is used by Mbed, so it should never be tested.
Also solve the potential problem with accidenty skipped peripherals in FPGA testing. Currently, we have a one `pinmap_restricted_peripherals()` function for all interfaces (UART, I2C, SPI, etc.).
The problem can be encountered if different interfaces have the same peripheral ids (e.g. `UART_0` = 0, `SPI_0` = 0). In this case, if `UART_0` is on the restricted list, then SPI tests will be also skipped for `SPI_0`.
The good news is that usually, the peripheral ids are the base addresses of the peripheral's register set, but we can't rely on this. It is also good that `pinmap_restricted_peripherals()` at this moment is only required for STDIO UART (Nuvoton and STM).
To solve this issue we will change name of `pinmap_restricted_peripherals()` to `pinmap_uart_restricted_peripherals()`, make STDIO UART restricted by default for all targets and update FPGA test utilily functions to use `pinmap_uart_restricted_peripherals()` to skip only uart peripherals.
In the future if needed we can consider to add support to restrict peripherals of other interfaces(SPI, I2C, etc).
This far all SFDP Sector Map Table related data has been found in small
pieces inside SPIFBlockDevice. Purpose was to consolidate the data
under one SFDP structure where all the information gathered from
SFDP tables is stored.
More generic version of a function used for parsing a Sector Map Table
was taken into use to avoid duplicate code. The implementation taken
into use is the one which got split from QSPIFBlockDevice and resides
now under the SFDP module.
This far all SFDP Sector Map Table related data has been found in small
pieces inside QSPIFBlockDevice. Purpose was to consolidate the data
under one SFDP structure where all the information gathered from
SFDP tables is stored.
Parsing a Sector Map Table was made more generic so that later it can be
moved under SFDP module. Once that is done it can be shared with
SPIFBlockDevice to avoid code duplication.
Martin Kojtal
Rajkumar Kanagaraj
Kimmo Vaisanen
Chun-Chieh Li
Stephan Brunner
Michal Paszta
Przemyslaw Stekiel
Leon Lindenfelser
midd
jeromecoutant
thegecko
Gabor Abonyi
Filip Jagodzinski
Shaik Abdul Sadiq
Veijo Pesonen