In case when base tick count is different than next tick count check first if the difference is equal to 1 tick (this is what we are looking for) if not then decrease the tick count.
Repeat counting process few times before incrementing the number of cycles in case when base tick count is equal to next tick count.
RTC reset test was failing when board has been just powered and RTC reset test was executed for the first time (issue has been detected on CI). In such case RTC initialization takes more time than in futher rtc_init calls. This has impact on green-tea communication. Commands send by host immediately after init command (write, read) were not handled on the device side and no response to the host was provided.
To fix this problem test communication flow has been modified. Device sends ack to the host after RTC init is done. Host sends further RTC commands when ack from the device has been received.
Edit:
There are still some communication issues on the CI. Add ack from the device after each executed command. Increase test timeout and wait after reset.
Since some platforms use RTC for low power timer RTC may be already enabled.
Because of that we will only verify if rtc_isenabled() returns 1 in case when init is done and RTC time is set.
Test inserts event into the TimerEvent object which is scheduled 50 ms in the future. Then test thread hangs on the semaphore for 51 ms and after that time we expect that event handler has been executed. This test fails sometimes on NRF51_DK, NRF52_DK since different clocks are used for event handling and delay. TimerEvent class uses fast us ticker and semaphores are based on lp ticker (NRF51_DK) or System Tick Timer (NRF52_DK).
We assume that ticker measurement error is 10% and our 1 [ms] extra corresponds to 2% error. I suggest to increase delay to 2 [ms] (4%). This should be enough for all boards at this moment.
It is possible that the difference between base and next tick count on some platforms is greater than 1, in this case we need to repeat counting with the reduced number of cycles (for slower boards).
If number of cycles has been reduced than base tick count needs to be redefined. This operation is missing and is added by this patch.
It has been noticed on NRF51_DK board that occurrence of system tick have impact on test execution.
NRF51_DK is a slow board with fast us ticker and handling of system tick interrupt takes about 250 us ticker ticks which have huge influence on interrupt tests where interrupt is set to <current count> + 100, 200, 500 ticks.
This test fails sometimes while testing 1 ms timeout on NRF51_DK board.
This board is very slow and lp ticker is inaccurate.
I noticed that measured results are very close to the tolerance value. For 1ms delay we measure in failure case 1560 us and tolerance is set to 550.
Since measurement method is also significantly flawed (extra time for setting up ticker and execution of a ticker irq handler) I recommend to increase tolerance by least +100 us for now.
Since now us ticker is disabled in deep-sleep mode and tests-mbed_drivers-timerevent verifies TimerEvent class which uses us ticker then deep-sleep mode needs to be disabled during the test execution.
On some boards without SYSTICK support lp ticker is used to trace system ticks.
Event queue uses system ticker to count delay when callback is to be fired.
New ticker implementation for NRF51_DK provides fast and accurate counter for us ticker which shows inaccuracy of the system ticker(which is based on slow and inaccurate lp ticker). This is why measured error grows linearly and percentage form needs to be used.
Currently we use constant tolerance value equal to: 5 [ms].
This patch modifies tolerance to the following form: 5% of measured time [ms].
In this test the lowest delay is equal to 100 [ms], so 5% corresponds to 5 [ms] tolerance - original value. This means that min tolerance is 5 [ms] so this change should not have negative impact on other targets.
For NR51_DK US_TICKER_OV_LIMIT needs to be increased since if test is run few times in row sometimes fails. This is because NR51_DK is a slow board (16 MHz) with fast and short us ticker counter 1 MHz/16 bits.
Since this change concerns new ticker driver for NRF51_DK it goas on ticker feature branch.
On this branch us ticker is based on 1 MHz higher precision counter (on master is based on 32kHz RTC). As a result of using higher precision counter measurement error increased:
:485::FAIL: Expected 1.060000 Was 1.070478
For delay 1060 ms we measured ~1070 ms so we have about ~1% measurement error which is not bed for this board.
To make it work with 1MHz us ticker increase test tolerance. Define tolerance as follows:
tolerance = 500us + 0.02 * delay.
Since this change concerns new ticker driver for NRF51_DK it goas on ticker feature branch.
On master NRF51_DK Ticker driver uses 32kHz RTC for lp and us ticker. Test uses us ticker to measure lp ticker interrupt scheduling (LowPowerTicker.attach), but since the same hardware is used for both tickers the measurement error is constant. On this branch us ticker uses 1 MHz higher precision clock and the results are different - measurement error grows linearly and shows inaccuracy of the RTC.
Test implements constant delta for measured time equal to 2000 us.
Change delta so it depends on lp ticker tested timeout value:
500us for measurement inaccuracy + 5% tolerance for LowPowerTicker
Update the ticker common test to clean up after each case by restoring
the ticker IRQ handler. This allows tickers to function normally after
each case has completed.
- count_ticks: fix counter overflow handling,
- count_ticks: use reg_cycles variable in while loop,
- increment test: reduce number of cycles for slow cores if measure process needs to be repeated (difference is greater than 1).
On slow targets with fast high frequency tickers like NRF51_DK (16 Mhz CPU/1MHz ticker) time window for test case execution without overflow needs to be increased. Add parameter to `overflow_protect` function to be able to set different time window without overflow for us ticker and lp ticker.
Increment test proves that ticker counter is incremented by one.
This is done indirectly for high frequency counters where it is impossible to read 'value' and 'value + 1' in two successive ticker reads.
This check is done indirectly by counting ticker ticks elapsed during execution of N cycles of empty while loop. Unfortunately on slow boards with fast tickers like NRF51_DK(16 MHz CPU/1MHz hf ticker) it is possible that for the same N cycles measured number of elapsed ticks in two successive calls is greater than 1. This patch provides fix for such case - measure operation is repeated with the same number of cycles.
Since target specific ticker drivers are not ready also features which uses ticker in upper layers may not work correctly and tests for these features.
We need to disable also failing higher level ticker related tests (by adding check if DEVICE_USTICKER symbol is available and raise #error [NOT_SUPPORTED] if not).
Note:
tests-mbed_drivers-rtc is new and uses us ticker to perform a delay.
count_ticks() function counts ticker ticks elapsed during execution of N cycles of empty while loop.
In current version N value (cycles) is given as volatile paramater in order to disable possible compiler optimalisation.
There was a problem with measured time on different compilers and additionally results on ARM compiler were unexpected (the difference beetween measured elapsed ticks for the same number of cycles was to large). This might be caused by the memory access in order to store updated variable in memory. To fix this issue given numer of cycles has been stored into register and register is decremented (no memory access).
With this fix count_ticks(NUM_OF_CYCLES, 1) call returns 2500 +/-1 for us ticker ticks using each compiler (K64F).
On some platforms (e.g. K64F) different counters are used for time measurement and interrupt generation.
Because of that we should relax interrupt test case and give additional time before checking if interrupt handler has been executed.
Since according to the ticker requirements min acceptable counter size is 12 bits (low power timer) for which max count is 4095, then all test cases must be executed in this time window.
HAL ticker layer handles overflow and it is not handled in the target ticker drivers.
Cruz Monrreal
deepikabhavnani
Veijo Pesonen
Kimmo Vaisanen
Przemyslaw Stekiel
Martin Kojtal
Bartek Szatkowski
Russ Butler
jeromecoutant
Russ Butler