It is quite possible that the user request for scheduling an uplink is deferred because of backoff or if it was a CONFIRMED message, a retry may take place on a different datarate and different channel.
We didn't have a hook for such deferred scheduling, telling the user whether the async rescheduling worked or not. This commit adds that capability and now we can tell the application if a scheduling failure took place after the original schedule request was accepted.
failed of its own accord) would prevent futher connect()'s due to the
CONN_IN_PROGRESS_FLAG remaining set. This change clears that flag in
the two cases described.
Ignore TEST_GROUP by AStyle. As this uses macro, is not visible to formatter.
By default, it assumes it is a function and treats methods as blocks inside a
function (inlined {}). We ignore it.
We might just not format UNITTESTS in the future if we face similar issues
in the future.
We had a bug especially in the reception path. Our recv window opening
delays were being calculated on the premise that the radio has to capture
5 preamble symbols out of 8 transmitted by the base station. However, in PHY
layer while setting radio rc settings, we were setting preamble length to be 8.
Preamble length register needs to be configured differently for Uplink and Downlink.
For uplink, we wish to transmit 8 preamble symbols whereas in the reception path we need
to receive 5 preamble symbols at least out of 8.
Alongwith that the maximum range of timing error may vary from platform to platform as it
is based upon the crystal in the chip. We have now made these parameters configurable and
have loaded them with the most optimal defaults.
The issue rose up when using ARMC6. A test case didn't initialize NetID
parameter for ABP while using connect(params) API. NetID is the first 7 bits
of the Device Address. It makes sense to actually remove the net-id parameter
from ABP settings as the stack can deduce it from device address. However, the ABP
structure is exposed in public APIs, so we can't really do that at the moment.
Simpler fix is to move the mask that helps us to extract first 7 bits of the device address
is exposed in lorawan_types.h and the user can use it to deduce correct net-id.
DR7 is used for FSK in AS932 region. As a default max DR, we should use a LoRa modulation
compatible data rate. Ofcourse if a device wishes to use FSK, it can set DR7 using set_data_rate() API
and turning off ADR, or an NS can configure a new channel for the device utilizing DR7.
The stack was trying to connect with default data rates which happened to be
the lowest data rates in a specific region. In the beginning device and NS do
not have agreed upon tx rx parameters and there can be synchronization issues.
When we use lower datarates, we may end up having a minute and a half long
transmissions that hnot only blocks the channel for a long time but also reduce
the chance of proper synch between device and NS. That's why we have decided to
begin with higher data rates and gradually decrease datarate if we do not hear
from the network server.
In the case when an automatic uplink was queued and the user do have something send,
we should give priority to user data instead od automatic uplink message.
This commit fixes some bugs from cancel_sending() method:
- System crashed if method was called before initialization.
Now LORAWAN_STATUS_NOT_INITIALIZED will be returned.
- Method returned LORAWAN_STATUS_BUSY error when no send request was pending.
LORAWAN_STATUS_OK should be returned in this case.
- LORAWAN_STATUS_BUSY is now returned if backoff timer is just about to be
dispatched (time_left returns 0).
I changed stack size because the deafult stack size may not be enough for
Ethernet of GR-PEACH(Cortex-A).
- Stack size is default size + 128 byte
In order to maximize the performance of Ethernet, I changed heap size to
below.
- Heap size is default size * 32 byte(send descriptor num is 16 and recv
descriptoer num is 16).
The integration is simply to define the macro MBEDTLS_HAVE_TIME_DATE
in the features/mbedtls/platform/inc/platform_mbed.h. The default
implementation of the mbedtls_time() function provided by mbed TLS is
sufficient to work with mbed OS because both use POSIX functions.
51f92b0efd introduced
handling for connection attempts while a connection was already underway or have been
completed. Unfortunately a similar check slipped through and the stack was not able to continue
sending join requests if an error happened.
Cruz Monrreal
Martin Kojtal
Juha Ylinen
paul-szczepanek-arm
Teppo Järvelin
Hasnain Virk
Wajahat Abbas
David Saada
deepikabhavnani
Edd Inglis
Antti Yli-Tokola
cyliangtw
Kimmo Vaisanen
Seppo Takalo
TomoYamanaka
Andres Amaya Garcia