This commit implements a SPI mode which will offer better performance
thanks to usage of Lower Layer API which use fewer registers access,
at the cost of lower robustness (no error management).
Following
Merge pull request #4063 from LMESTM/17q2_L4_bootloader
the NUCLEO_L476RG binairies could not boot anymore.
The change done in #4063 was derived from work on NUCLEO_L429ZI target
which supports uvisor. The VECTORS defintiion is introduced as part of
uvisor support and requires further changes in ld file which were missing.
As uvisor is not considered yet, we remove VECTORS for now and will
introduce only when needed.
Remove HAL_Init and related code from SystemInit and move it to
mbed_sdk_init. The function SystemInit is called early in the boot
sequence before RAM is initialized or the VTOR is setup, so it should
not be used to perform the HAL initialization.
This fixes crashes due the vector table being used before it has been
relocated.
This reduces the number of loads inside of the .data copy loop by 3 by using one more register. It should work on any STM32 with at least 5 general-purpose registers. If only 4 are available, then 1 load could still be removed from the original implementation.
Restore cmsis_nvic (cmsis_nvic.c and cmsis_nvic.h) files for the
implementations which use a mechanism other than the VTOR to set
interrupts. These are vendor specific and were done for M0 devices
which do not have a VTOR.
Note - There were two cmsis_nvic files which did not use the VTOR that
which not restored in this patch. This is because these targets were
not M0 devices and could use the new unified implementation instead.
These files are:
targets\TARGET_ARM_SSG\TARGET_MPS2\TARGET_MPS2_M0P\device\cmsis_nvic.c
targets\TARGET_ONSEMI\TARGET_NCS36510\device\cmsis_nvic.c
Note - cmsis_nvic.c and cmsis_nvic.h were initial removed in
(and restored from) the commit:
b97ffe8fdc -
"CMSIS5: Replace target defined NVIC_Set/GetVector with CMSIS implementation"
Note that this could have side effects on the application as it would
not be aware that data has been missed. This may be later solved by
adding an error management parameter to the Serial API in mbed.
The advantage is that the serial link can work again.
The use of mktime was causing a fault when called in interrupt handler because on GCC it lock the mutex protecting the environment, To overcome this issue, this patch add dedicated routine to convert a time_t into a tm and vice versa.
In the process mktime has been optimized and is now an order of magnitude faster than the routines present in the C library.
Add MBED_APP_START and MBED_APP_SIZE to the linker scripts
so the start and size of an image can be specified. This allows the
ROM to be split into a bootloader region and an application region.
Fix vector table
The address of the vector table is hardcoded to the start of flash.
This patch updates make it properly handle updating the VTOR with
a bootloader.
TimMasterHandle.Instance initialization can be removed from here,
because it will either have been already done previously,
or it will be done in the us_ticker_init() call immediately below.
Following previous fixes on 16 tickers handling, the overflow flag
condition will not happen anymore, so the work-around in place is
not needed anymore
This commit simplifies ticker interrupt set function and handler.
There were issues around the 16 bits timer wrap-around timing as we were
aligning interrupts with wrap-around limits (0xFFFF) and then reading
TIM_MST->CNT again in timer_update_irq_handler which could lead
to crossing case with the wrap-around (TIM_FLAG_UPDATE) case.
Now we're using the 16 lower bits of the timestamp as the reference from
using in set_compare and never changing it. There is also no need to set
comparator again in timer_update_irq_handler. This is more robust and
also more efficient.
Move to a single more reliable implementation of us_ticker_read()
There were historically 2 versions of us_ticker_read() implementation.
The one removed here was not reliable because us_ticker_read() can be
called in interrupt context which means that TIM_MST->CNT would have
wrapped around while SlaveCounter is not yet updated. So there is a need
to check the TIM_FLAG_UPDATE inside this function, which was not done in
the implementation that is removed here.
As reported in issue #4214, there are seen issues seen first on
NUCLEO_F103RB in case of successive Reads of 1 byte at a time.
This issue is due to a wrong state management in the end of read sequence.
Also F1 i2c driver was not fully aligned to others, which is updated here.
There were still side effects, in particular on I2C master slave test,
when setting by default the Pin Speed for F1 family. So for F1 family,
let's do it only in case of Output which is the only case where this
actually applies on this family.
For STM32 targets using a 32-bit timer for the microsecond ticker, the
driver did not properly handle timestamps that are in the past. It
would just blindly set the compare register to the requested timestamp,
resulting in the interrupt being serviced up to 4295 seconds late
(i.e. after the 32-bit timer counts all the way around to hit the
timestamp again).
This problem can easily be reproduced by creating a Timeout object
then calling the timeout's attach_us() member function to attach a
callback with a timeout of 0 us. The callback will not get called for
over 2147 seconds, and possibly up to 4295 seconds late if no other
microsecond ticker events are getting scheduled in the meantime.
Now, after the compare register has been set, the timestamp is checked
against the current time to see if the timestamp is in the past, and
if so, the compare event is manually set.
NOTE: By checking if the timestamp is in the past after configuring the
capture register, we ensure proper handling in the case where the timer
updates past the timestamp while setting the capture register.
For keep supporting external APIs with the same name (supposedly there are a larger
number of users of those APIs), BufferedSerial and ATParser are being renamed.
BufferedSerial becomes UARTSerial, will complement a future USBSerial etc.
ATParser becomes ATCmdParser.
* UARTSerial moves to /drivers
* APN_db.h is moved from platform to cellular/util/.
* Original CellularInterface is restored for backward compatability (again, supposedly there
are users of that).
* A new file, CellularBase is added which will now servce as the base class for all
upcoming drivers.
* Special restructuring for the driver has been undertaken. This makes a clear cut distinction
between an on-board or an off-board implementation.
- PPPCellularInterface is a generic network interface that works with a generic FileHandle
and PPP. A derived class is needed to pass that FileHandle.
- PPPCellularInterface provides some base functionality like network registration, AT setup,
PPP connection etc. Lower level job is delegated to the derived classes and various modem
specific APIs are provided which are supposed to be overridden.
- UARTCellularInterface is derived from PPPCellularInterface. It constructs a FileHandle and
passes it back to PPPCellularInterface as well as provides modem hangupf functionality.
In future we could proive a USBInterface that would derive from PPPCellularInterface and could
pass the FileHandle back.
- OnboardCellularInterface is derived from UARTCellularInterfae and provides hooks to
the target provided implementation of onbard_modem_api.h. An off-board modem, i.e, a modem on
a shield has to override the modem_init(), modem_power_up() etc as it cannot use
onboard_modem_api.h.
This provides a HAL layer for Modem bearing devices.
Provides a standard interface to upper layer drivers.
Platform providers will be implementing this API under their
specific targets.
As a reference, two implementations are provided under TARGET_C027 (UBLOX)
and TARGET_MTS_DRAGONFLY_F411RE (MultiTech).
targets.json now contains a tag "MODEM" which tells that this target
has a modem and the modem_api is protected by a flag DEVICE_MODEM
(following the DEVICE_SERIAL fashion ).
* Lays down ground for mbed modem_api
* Standardizes pin names relating to modem device for UBLOX C027 and MTS_DRAGONFLY_F411RE
devices
* Ublox modem api is changed to use a standard, platform independent name so that same
api could be used with multiple ubloc modems.
* DCD Polarity macro is added to assist the driver in knowing correct polarity
There is an easy default implementation of spi_master_block_write that
just calls spi_master_write in a loop, so the default implementation
of spi_master_block_write has been added to all targets.
Reworked the serial_format() function for STM32F0x
devices to take the format in the form:
data_bits - parity - stop_bits
E.g. 8 - N - 1
where data_bits exclude the parity bit.
Added a case for 7 bits data as at least the chips
STM32F0x1/STM32F0x2/STM32F0x8 support 7 bits data.
Consolidated serial_format() and uart_init()
functions into a general TARGET_STM serial_api.c
file since the functions are common to all STM targets.
Fixes#4189
arostm
jeromecoutant
Martin Kojtal
Jimmy Brisson
Anna Bridge
bcostm
Mike Fiore
andreas.larsson
Laurent MEUNIER
Rob Meades
Andreas Larsson
Russ Butler
Fahrzin Hemmati
Sam Grove
Vincent Coubard
Bradley Scott
mickeyln
Hasnain Virk
Bartek Szatkowski
Francisco J. Manno