Moving some code in common to be able to manage several ADC instances,
or several channels of an instance.
The change involves:
- moving dac_s structure definition to common_object.h
- create TARGET_STM/analogout_api.c and move fully common analog_out
functions in there
- rename analogout_api.c of each target family into analogout_device.c
to keep platform specific code
- update analogout_device.c to rely on obj->handle and obj->channel
- align analogout_init function as much as possible between families in
analogout_device.c files
This commit implements a SPI mode which will offer better performance
thanks to usage of Lower Layer API which use fewer registers access,
at the cost of lower robustness (no error management).
Remove HAL_Init and related code from SystemInit and move it to
mbed_sdk_init. The function SystemInit is called early in the boot
sequence before RAM is initialized or the VTOR is setup, so it should
not be used to perform the HAL initialization.
This fixes crashes due the vector table being used before it has been
relocated.
This reduces the number of loads inside of the .data copy loop by 3 by using one more register. It should work on any STM32 with at least 5 general-purpose registers. If only 4 are available, then 1 load could still be removed from the original implementation.
Restore cmsis_nvic (cmsis_nvic.c and cmsis_nvic.h) files for the
implementations which use a mechanism other than the VTOR to set
interrupts. These are vendor specific and were done for M0 devices
which do not have a VTOR.
Note - There were two cmsis_nvic files which did not use the VTOR that
which not restored in this patch. This is because these targets were
not M0 devices and could use the new unified implementation instead.
These files are:
targets\TARGET_ARM_SSG\TARGET_MPS2\TARGET_MPS2_M0P\device\cmsis_nvic.c
targets\TARGET_ONSEMI\TARGET_NCS36510\device\cmsis_nvic.c
Note - cmsis_nvic.c and cmsis_nvic.h were initial removed in
(and restored from) the commit:
b97ffe8fdc -
"CMSIS5: Replace target defined NVIC_Set/GetVector with CMSIS implementation"
Note that this could have side effects on the application as it would
not be aware that data has been missed. This may be later solved by
adding an error management parameter to the Serial API in mbed.
The advantage is that the serial link can work again.
For STM32 targets using a 32-bit timer for the microsecond ticker, the
driver did not properly handle timestamps that are in the past. It
would just blindly set the compare register to the requested timestamp,
resulting in the interrupt being serviced up to 4295 seconds late
(i.e. after the 32-bit timer counts all the way around to hit the
timestamp again).
This problem can easily be reproduced by creating a Timeout object
then calling the timeout's attach_us() member function to attach a
callback with a timeout of 0 us. The callback will not get called for
over 2147 seconds, and possibly up to 4295 seconds late if no other
microsecond ticker events are getting scheduled in the meantime.
Now, after the compare register has been set, the timestamp is checked
against the current time to see if the timestamp is in the past, and
if so, the compare event is manually set.
NOTE: By checking if the timestamp is in the past after configuring the
capture register, we ensure proper handling in the case where the timer
updates past the timestamp while setting the capture register.
Reworked the serial_format() function for STM32F0x
devices to take the format in the form:
data_bits - parity - stop_bits
E.g. 8 - N - 1
where data_bits exclude the parity bit.
Added a case for 7 bits data as at least the chips
STM32F0x1/STM32F0x2/STM32F0x8 support 7 bits data.
Consolidated serial_format() and uart_init()
functions into a general TARGET_STM serial_api.c
file since the functions are common to all STM targets.
Fixes#4189
When we want to activate USE_FULL_ASSERT macro in STM32 CUBE, there is a
need to have the assert map to MBED.
The easiest way to have this definition in a single place for all STM32
HAL and LL files using it, is to add a specific header file where the
porting to MBED is done.
Revert HRM1017 file source deletion
Added in small comment next to additions
Added mapping to BTN-labelled switches
Added mapping to USER_BUTTON-labelled switches
Undo incorrect mapping to SWIO pin in NORDIC target
Before this patch, many warnings like below were generated
during compilation with ArmCC
[Warning] lwip_ethernet.h@57,0: #3135-D: attribute does not apply to any entity
This happens here as ``--gnu`` option of ArmCC is being used, which
enables the GNU compiler extensions that the ARM compiler supports.
This is solve by adding a extra check on __CCARM .
The pwmout driver is very similar for each STM32 family.
The only family specific part is defined in pwmout_device.h file.
It mainly contains few specific information:
- The mapping of PWM/TIMERS to APB1 or APB2 so that we can get the clock
- The clock calculation uses the right APB clock, which was sometimes
not the case before and could have lead to errors in case dividers were
enabled on APB clock settings. This case is now covered.
- Inactivation of inverted support on feaw families
this first makes pinmap.c a common file
then rework it with several goals:
- avoid gpio / irq / pin management extra dependencies
- improve performances when switching between pin modes
This change is based on LL layer to access to registers level
instead of using HAL higher level API.
The family specific functions are implemented in pin_device.h
of each family. Mostly this is F1 family that is differnt
from other ones.
Instead of using HAL_GPIO_Init / Deinit which makes a lot of registers
being written and re-written, and which creates extra gpio / pin / irq
dependencies, we directly set the IRQ related registers thanks for the
STM32 LL layers which provides APIs to modify registers.
Jimmy Brisson
Laurent MEUNIER
Anna Bridge
jeromecoutant
Martin Kojtal
Russ Butler
Fahrzin Hemmati
Sam Grove
Bradley Scott
mickeyln
Bartek Szatkowski
Francisco J. Manno
adustm
Kevin Gilbert
Christopher Haster
bcostm