Previously, we weren't filling in RX1 frequecny in rx_window1_config
structure. However, everything worked as in LoRaPHY::rx_config() API
there was a check which filled in correct RX1 frequency.
Now we are filling in RX1 freq. properly while we are computing
parameters for RX1 window.
The idea behind the method post_process_no_reception() is to post
process any outgoing TX but we shouldn't do that if a CONFIRMED message
is outgoing and there are still some retries left.
After transmission we should change the state before invoking opening of
slots as we may start receiving in the rx slots and the state would
suddenly change from SENDING to RECEIVING without going through the
ACK_WAIT state (in case of CONFIRMED messages). Tests show that after
this slight adjustment, our number of ack retries have significantly
reduced.
LinkADRReq mac command can be used by the network server to set a
certain level of QOS using NbTrans field which is applicable to
Unconfirmed traffic only for 1.0.2 spec.
This commit introduces mechanisms to facilitate this QOS. It means to
repeat an outgoing unconfirmed message NbTrans times without changing
its frame counter.
For class C, we have retired the ack_expiry_timer_for_class_c and have
replaced it with another timer which mimics the RX2 closure as in Class
A but doesn't actually close RX2 window. It's just a mechanism by which
the state machine is informed that the you can proceed forward, we have
not received anything in RX2 window either. This is needed as RX2
doesn't timeout in class C (i.e., the radio remains in continuous mode).
In addition to that we need to close any pending timers for Receive
windows after the MIC has passed and the Duplicate counter check has
also been passed.
Before going after an automatic uplink, we should check if there was an
automatic uplink already ongoing, i.e., the ack for the previous
automatic uplink cycle has not been received.
If there is we shouldn't queue the new automatic uplink and wait for
the previous Ack cycle to complete.
1. RTOS is needed only for Stack stats
Move+Add all required header files for RTOS into MBED_STACK_STATS_ENABLED
define. Also added 'using namespace'
2. Add heap stats only when MBED_HEAP_STATS_ENABLED
Change error from `MBEDTLS_PLATFORM_HW_FAILED` to
`MBEDTLS_PLATFORM_HW_ACCEL_FAILED` and the value to 0x70,
as the previous value cannot be used as a low level error code.
Provide TLSSocket implementation. This implementation allows TLSSocket
to wrap around any existing socket. Currently only TLS supported. DTLS
not yet implemented.
Design document also provided with the implementation.
Documentation submitted to Mbed OS handbook.
Make the following changes to doxyfile_options:
-Change CASE_SENSE_NAMES so names of files generated match mbed-os docs
-Change DISABLE_INDEX so navigation bar shows
-Change CLASS_DIAGRAMS so inheritance diagram gets generated
-Change USE_MDFILE_AS_MAINPAGE and add DOXYGEN_FRONTPAGE.md to
FILE_PATTERNS so the correct main page is found and used
-Remove DEVICE_ETH from PREDEFINED since this is no longer relevent
-Change GENERATE_XML and XML_OUTPUT so no xml is generated
-Change SEARCHENGINE to match the docs
Make the following changes in doxygen_options.json:
-Add all non-default values in doxyfile_options to the json
-Break json into 3 groups
1. Values that are the same as doxyfile_options
2. Values that must be different from doxyfile_options
3. Values the are overriden by the docs builder
-Make the doxyegn search directory "INPUT" start in mbed-os rather
than one level above mbed-os.
Finally, rename the BLE doxygen front page so it is not confused with
the mbed-os front page.
Add re-scan routine goto if message is caused user callback
This will fix hard fault when blockwise message sending timeouts. This happens cause same list is manipulated through rx callback.
Static Thread methods and signal methods have been deprecated. Remove
all references in the main code, and most of the tests. Some tests of
the deprecated APIs themselves remain.
Revert deprecation of FlashIAPBlockDevice 2 argument constructor has this was a breaking change. This follows a similar change in the external flashiap-driver repo.
For Windows-formatted SD card, it is not partitioned (no MBR), but its PBR has the
same boot signature (0xaa55) as MBR. We would easily mis-recognize this SD card has valid
partitions if we only check partition type. We add check by only accepting 0x00 (inactive)
/0x80 (active) for valid partition status.
New classes covered with unit tests: SocketAddress, EthernetInterface, EMACInterface, WiFiAccessPoint.
Also added missing namespace in front of mbed::Callback usages.
EMACInterface is covered by the EthernetInterface unit tests.
When socket created using accept() is closed by calling the close()
method, "delete this" is executed which triggers the destructor call
on TCPSocket which in turn calls close() once again. Because _stack
is already 0 this results in a hard-fault.
Add a check that skips the rest of the close() method is the _stack
is already 0.
Missing CellularSocket constructor caused uninitialized values to be used.
Also changed comparision macros to ASSERT_EQ as suggested by GoogleTest guide.
If the packet is already handed over to the PHY layer, we shouldn't be
able to cancel that particular transmission. In addition to that if the
backoff timer is either not applied or has been deactivated, should end
up in no-op rather than having normal termination. A new error code has
been introduced to cover no-op cases. This error code replaces the
compliance test related error code which is no longer relevant.
clear_tx_pipe() does nothing if:
- The stack cannot cancel TX (already handed over to PHY)
- The backoff timer is not active at all
- The event is disaptched to schedule
stop_sending() will only post process ongoin TX if the pipe was
definitely cleared.
- Add function that can be used to clear the received blockwise payloads for example in the case of a connection error.
- Silence compiler warning when CoAP duplicate detection is enabled.
Previously, we weren't filling in RX1 frequecny in rx_window1_config
structure. However, everything worked as in LoRaPHY::rx_config() API
there was a check which filled in correct RX1 frequency.
Now we are filling in RX1 freq. properly while we are computing
parameters for RX1 window.
The idea behind the method post_process_no_reception() is to post
process any outgoing TX but we shouldn't do that if a CONFIRMED message
is outgoing and there are still some retries left.
After transmission we should change the state before invoking opening of
slots as we may start receiving in the rx slots and the state would
suddenly change from SENDING to RECEIVING without going through the
ACK_WAIT state (in case of CONFIRMED messages). Tests show that after
this slight adjustment, our number of ack retries have significantly
reduced.
LinkADRReq mac command can be used by the network server to set a
certain level of QOS using NbTrans field which is applicable to
Unconfirmed traffic only for 1.0.2 spec.
This commit introduces mechanisms to facilitate this QOS. It means to
repeat an outgoing unconfirmed message NbTrans times without changing
its frame counter.
For class C, we have retired the ack_expiry_timer_for_class_c and have
replaced it with another timer which mimics the RX2 closure as in Class
A but doesn't actually close RX2 window. It's just a mechanism by which
the state machine is informed that the you can proceed forward, we have
not received anything in RX2 window either. This is needed as RX2
doesn't timeout in class C (i.e., the radio remains in continuous mode).
In addition to that we need to close any pending timers for Receive
windows after the MIC has passed and the Duplicate counter check has
also been passed.
Before going after an automatic uplink, we should check if there was an
automatic uplink already ongoing, i.e., the ack for the previous
automatic uplink cycle has not been received.
If there is we shouldn't queue the new automatic uplink and wait for
the previous Ack cycle to complete.
TB_SENSE_12 would have been left behind by the changes in #7778. This commit implements the changes in mbed to allow targets to provide a default network interface for Silicon Labs targets.
Martin Kojtal
Kimmo Vaisanen
Hasnain Virk
deepikabhavnani
Cruz Monrreal
Ron Eldor
Michal Paszta
Ari Parkkila
Seppo Takalo
Russ Butler
Brian Esquilona
Amanda Butler
Antti Yli-Tokola
Kevin Bracey
Anna Bridge
Yossi Levy
Oren Cohen
Mirela Chirica
ccli8
mudassar-ublox
Sławek Piotrowski
Arto Kinnunen
paul-szczepanek-arm
Simon Butcher
Andrew Leech
Moran Peker
Leon Lindenfelser
Jaakko Korhonen
Nir Sonnenschein
Antti Kauppila
cedrick kukela
Juho Eskeli
pingdan32
jeromecoutant
Jarkko Paso
David Saada
Steven
Aashish chaddha
Teppo Järvelin