Merge pull request #397 from 0xc0170/dev_k20d50m

[K20D50M] K20D5M -> K20D50M

libraries/mbed/targets/hal/TARGET_Freescale/TARGET_K20D50M/PinNames.h

@@ -197,10 +197,10 @@ typedef enum {
     LED_BLUE  = PTA2,
 
     // mbed original LED naming
-    LED1 = LED_BLUE,
+    LED1 = LED_RED,
     LED2 = LED_GREEN,
-    LED3 = LED_RED,
-    LED4 = LED_RED,
+    LED3 = LED_BLUE,
+    LED4 = LED_BLUE,
 
     // USB Pins
     USBTX = PTB17,
@@ -231,6 +231,12 @@ typedef enum {
     A4 = PTB1,
     A5 = PTB0,
 
+    I2C_SCL = D15,
+    I2C_SDA = D14,
+
+    TSI_ELEC0 = PTB16,
+    TSI_ELEC1 = PTB17,
+
     // Not connected
     NC = (int)0xFFFFFFFF
 } PinName;

libraries/mbed/targets/hal/TARGET_Freescale/TARGET_K20D50M/analogin_api.c

@@ -20,6 +20,8 @@
 #include "pinmap.h"
 #include "clk_freqs.h"
 
+#define MAX_FADC        6000000
+
 static const PinMap PinMap_ADC[] = {
     {PTC2, ADC0_SE4b, 0},
     {PTD1, ADC0_SE5b, 0},
@@ -34,8 +36,6 @@ static const PinMap PinMap_ADC[] = {
     {NC,   NC,        0}
 };
 
-#define MAX_FADC        6000000
-
 void analogin_init(analogin_t *obj, PinName pin) {
     obj->adc = (ADCName)pinmap_peripheral(pin, PinMap_ADC);
     MBED_ASSERT(obj->adc != (ADCName)NC);

libraries/mbed/targets/hal/TARGET_Freescale/TARGET_K20D50M/gpio_irq_api.c

@@ -30,45 +30,63 @@ static gpio_irq_handler irq_handler;
 #define IRQ_EITHER_EDGE     PORT_PCR_IRQC(11)
 
 static void handle_interrupt_in(PORT_Type *port, int ch_base) {
-    uint32_t mask = 0, i;
+    uint32_t isfr;
+    uint32_t pin;
 
-    for (i = 0; i < 32; i++) {
-        uint32_t pmask = (1 << i);
-        if (port->ISFR & pmask) {
-            mask |= pmask;
-            uint32_t id = channel_ids[ch_base + i];
-            if (id == 0)
-                continue;
-
-            GPIO_Type *gpio = PTA;
-            gpio_irq_event event = IRQ_NONE;
-            uint32_t port_num = (port - PORTA) >> 12;
-            switch (port->PCR[i] & PORT_PCR_IRQC_MASK) {
-                case IRQ_RAISING_EDGE:
-                    event = IRQ_RISE;
-                    break;
-
-                case IRQ_FALLING_EDGE:
-                    event = IRQ_FALL;
-                    break;
-
-                case IRQ_EITHER_EDGE:
-                    gpio += (port_num * 0x40);
-                    event = (gpio->PDIR & pmask) ? (IRQ_RISE) : (IRQ_FALL);
-                    break;
-            }
-            if (event != IRQ_NONE)
-                irq_handler(id, event);
+    while ((isfr = port->ISFR) != 0) {
+        pin = 31 - __CLZ(isfr);
+        uint32_t id = channel_ids[ch_base + pin];
+        if (id == 0) {
+            continue;
         }
+
+        GPIO_Type *gpio = PTA;
+        gpio_irq_event event = IRQ_NONE;
+        uint32_t port_num = (port - PORTA) >> 12;
+
+        switch (port->PCR[pin] & PORT_PCR_IRQC_MASK) {
+            case IRQ_RAISING_EDGE:
+                event = IRQ_RISE;
+                break;
+            case IRQ_FALLING_EDGE:
+                event = IRQ_FALL;
+                break;
+            case IRQ_EITHER_EDGE:
+                gpio += (port_num * 0x40);
+                event = (gpio->PDIR & (1 << pin)) ? (IRQ_RISE) : (IRQ_FALL);
+                break;
+        }
+        if (event != IRQ_NONE) {
+            irq_handler(id, event);
+        }
+        port->ISFR = 1 << pin;
     }
-    port->ISFR = mask;
 }
 
-void gpio_irqA(void) {handle_interrupt_in(PORTA, 0);}
-void gpio_irqB(void) {handle_interrupt_in(PORTB, 32);}
-void gpio_irqC(void) {handle_interrupt_in(PORTC, 64);}
-void gpio_irqD(void) {handle_interrupt_in(PORTD, 96);}
-void gpio_irqE(void) {handle_interrupt_in(PORTE, 128);}
+void gpio_irqA(void) {
+    handle_interrupt_in(PORTA, 0);
+}
+
+void gpio_irqB(void)
+{
+    handle_interrupt_in(PORTB, 32);
+}
+
+void gpio_irqC(void)
+{
+    handle_interrupt_in(PORTC, 64);
+}
+
+void gpio_irqD(void)
+{
+    handle_interrupt_in(PORTD, 96);
+}
+
+void gpio_irqE(void)
+{
+    handle_interrupt_in(PORTE, 128);
+}
+
 
 int gpio_irq_init(gpio_irq_t *obj, PinName pin, gpio_irq_handler handler, uint32_t id) {
     if (pin == NC)

libraries/mbed/targets/hal/TARGET_Freescale/TARGET_K20D50M/serial_api.c

@@ -26,12 +26,20 @@
 
 static const PinMap PinMap_UART_TX[] = {
     {PTB17, UART_0, 3},
-    {NC  ,  NC    , 0}
+    {PTC4 , UART_1, 3},
+    {PTD3 , UART_2, 3},
+    {PTD7 , UART_0, 3},
+    {PTE0 , UART_1, 3},
+    {NC   , NC    , 0}
 };
 
 static const PinMap PinMap_UART_RX[] = {
     {PTB16, UART_0, 3},
-    {NC  ,  NC    , 0}
+    {PTC3 , UART_1, 3},
+    {PTD2 , UART_2, 3},
+    {PTD6 , UART_0, 3},
+    {PTE1 , UART_1, 3},
+    {NC   , NC    , 0}
 };
 
 #define UART_NUM    3
@@ -52,18 +60,33 @@ void serial_init(serial_t *obj, PinName tx, PinName rx) {
     obj->uart = (UART_Type *)uart;
     // enable clk
     switch (uart) {
-        case UART_0: SIM->SOPT2 |= SIM_SOPT2_PLLFLLSEL_MASK;
-                     SIM->SCGC5 |= SIM_SCGC5_PORTA_MASK; SIM->SCGC4 |= SIM_SCGC4_UART0_MASK; break;
-        case UART_1: SIM->SCGC5 |= SIM_SCGC5_PORTC_MASK; SIM->SCGC4 |= SIM_SCGC4_UART1_MASK; break;
-        case UART_2: SIM->SCGC5 |= SIM_SCGC5_PORTD_MASK; SIM->SCGC4 |= SIM_SCGC4_UART2_MASK; break;
+        case UART_0:
+            SIM->SOPT2 |= SIM_SOPT2_PLLFLLSEL_MASK;
+            SIM->SCGC5 |= SIM_SCGC5_PORTA_MASK;
+            SIM->SCGC4 |= SIM_SCGC4_UART0_MASK;
+            break;
+        case UART_1:
+            SIM->SCGC5 |= SIM_SCGC5_PORTC_MASK;
+            SIM->SCGC4 |= SIM_SCGC4_UART1_MASK;
+            break;
+        case UART_2:
+            SIM->SCGC5 |= SIM_SCGC5_PORTD_MASK;
+            SIM->SCGC4 |= SIM_SCGC4_UART2_MASK;
+            break;
     }
     // Disable UART before changing registers
     obj->uart->C2 &= ~(UART_C2_RE_MASK | UART_C2_TE_MASK);
 
     switch (uart) {
-        case UART_0: obj->index = 0; break;
-        case UART_1: obj->index = 1; break;
-        case UART_2: obj->index = 2; break;
+        case UART_0:
+            obj->index = 0;
+            break;
+        case UART_1:
+            obj->index = 1;
+            break;
+        case UART_2:
+            obj->index = 2;
+            break;
     }
 
     // set default baud rate and format
@@ -131,9 +154,20 @@ void serial_format(serial_t *obj, int data_bits, SerialParity parity, int stop_b
 
     uint32_t parity_enable, parity_select;
     switch (parity) {
-        case ParityNone: parity_enable = 0; parity_select = 0; break;
-        case ParityOdd : parity_enable = 1; parity_select = 1; data_bits++; break;
-        case ParityEven: parity_enable = 1; parity_select = 0; data_bits++; break;
+        case ParityNone:
+            parity_enable = 0;
+            parity_select = 0;
+            break;
+        case ParityOdd :
+            parity_enable = 1;
+            parity_select = 1;
+            data_bits++;
+            break;
+        case ParityEven:
+            parity_enable = 1;
+            parity_select = 0;
+            data_bits++;
+            break;
         default:
             break;
     }

workspace_tools/build_release.py

@@ -45,6 +45,7 @@ OFFICIAL_MBED_LIBRARY_BUILD = (
     ('KL25Z',        ('ARM', 'GCC_ARM')),
     ('KL46Z',        ('ARM', 'GCC_ARM')),
     ('K64F',         ('ARM', 'GCC_ARM')),
+    ('K20D50M',      ('ARM', 'GCC_ARM')),
 
     ('NUCLEO_F030R8', ('ARM', 'uARM')),
     ('NUCLEO_F072RB', ('ARM', 'uARM')),

workspace_tools/export/gccarm.py

@@ -28,7 +28,7 @@ class GccArm(Exporter):
         'KL25Z',
         'KL46Z',
         'K64F',
-        'K20D5M',
+        'K20D50M',
         'LPC4088',
         'LPC11U24',
         'LPC1114',

workspace_tools/export/uvision4.py

@@ -28,7 +28,7 @@ class Uvision4(Exporter):
         'KL25Z',
         'KL46Z',
         'K64F',
-        'K20D5M',
+        'K20D50M',
         'LPC1347',
         'LPC1114',
         'LPC11C24',

workspace_tools/targets.py

@@ -124,7 +124,7 @@ class KL46Z(Target):
         self.is_disk_virtual = True
 
 
-class K20D5M(Target):
+class K20D50M(Target):
     def __init__(self):
         Target.__init__(self)
         self.core = "Cortex-M4"
@@ -550,7 +550,7 @@ TARGETS = [
     KL05Z(),
     KL25Z(),
     KL46Z(),
-    K20D5M(),
+    K20D50M(),
     K64F(),
     LPC812(),
     LPC810(),