diff --git a/targets/TARGET_NUVOTON/TARGET_M251/analogin_api.c b/targets/TARGET_NUVOTON/TARGET_M251/analogin_api.c
index 087be9ab52..256b839972 100644
--- a/targets/TARGET_NUVOTON/TARGET_M251/analogin_api.c
+++ b/targets/TARGET_NUVOTON/TARGET_M251/analogin_api.c
@@ -55,19 +55,22 @@ void analogin_init(analogin_t *obj, PinName pin)
     MBED_ASSERT(modinit != NULL);
     MBED_ASSERT(modinit->modname == (int) obj->adc);
 
+    // Wire pinout
+    pinmap_pinout(pin, PinMap_ADC);
+
     EADC_T *eadc_base = (EADC_T *) NU_MODBASE(obj->adc);
 
     // NOTE: All channels (identified by ADCName) share a ADC module. This reset will also affect other channels of the same ADC module.
     if (! eadc_modinit_mask) {
-        // Reset this module if no channel enabled
-        SYS_ResetModule(modinit->rsetidx);
-
         // Select clock source
         CLK_SetModuleClock(modinit->clkidx, modinit->clksrc, modinit->clkdiv);
 
         // Enable clock
         CLK_EnableModuleClock(modinit->clkidx);
 
+        // Reset this module if no channel enabled
+        SYS_ResetModule(modinit->rsetidx);
+
         /* Configure EADC_module to be ready to convert
          * M251 doesn't support 'input mode' feature. Configure it to 0. */
         EADC_Open(eadc_base, 0);
@@ -75,9 +78,6 @@ void analogin_init(analogin_t *obj, PinName pin)
 
     uint32_t chn =  NU_MODSUBINDEX(obj->adc);
 
-    // Wire pinout
-    pinmap_pinout(pin, PinMap_ADC);
-
     // Configure the sample module Nmod for analog input channel Nch and software trigger source
     EADC_ConfigSampleModule(eadc_base, chn, EADC_SOFTWARE_TRIGGER, chn);
 
diff --git a/targets/TARGET_NUVOTON/TARGET_M251/analogout_api.c b/targets/TARGET_NUVOTON/TARGET_M251/analogout_api.c
index e80b020c33..b12775a985 100644
--- a/targets/TARGET_NUVOTON/TARGET_M251/analogout_api.c
+++ b/targets/TARGET_NUVOTON/TARGET_M251/analogout_api.c
@@ -53,20 +53,23 @@ void analogout_init(dac_t *obj, PinName pin)
     uint32_t chn =  NU_MODSUBINDEX(obj->dac);
     MBED_ASSERT(chn < NU_DACCHN_MAXNUM);
 
+    /* Wire pinout */
+    pinmap_pinout(pin, PinMap_DAC);
+
     DAC_T *dac_base = (DAC_T *) NU_MODBASE(obj->dac);
 
     /* Module-level setup from here */
 
-    if (! dac_modinit_mask[modidx]) {
-        /* Reset IP */
-        SYS_ResetModule(modinit->rsetidx);
-        
+    if (! dac_modinit_mask[modidx]) {        
         /* Select IP clock source and clock divider */
         CLK_SetModuleClock(modinit->clkidx, modinit->clksrc, modinit->clkdiv);
 
         /* Enable IP clock */
         CLK_EnableModuleClock(modinit->clkidx);
 
+        /* Reset IP */
+        SYS_ResetModule(modinit->rsetidx);
+
         /* The conversion settling time is 6us when 12-bit input code transition from
          * lowest code (0x000) to highest code (0xFFF). */
         DAC_SetDelayTime(dac_base, 6);
@@ -80,9 +83,6 @@ void analogout_init(dac_t *obj, PinName pin)
 
     /* Set the software trigger, enable DAC event trigger mode and enable D/A converter */
     DAC_Open(dac_base, chn, DAC_SOFTWARE_TRIGGER);
-        
-    /* Wire pinout */
-    pinmap_pinout(pin, PinMap_DAC);
 
     /* Mark channel allocated */
     dac_modinit_mask[modidx] |= 1 << chn;
diff --git a/targets/TARGET_NUVOTON/TARGET_M251/dma_api.c b/targets/TARGET_NUVOTON/TARGET_M251/dma_api.c
index a8a23b0573..8407118043 100644
--- a/targets/TARGET_NUVOTON/TARGET_M251/dma_api.c
+++ b/targets/TARGET_NUVOTON/TARGET_M251/dma_api.c
@@ -52,12 +52,12 @@ void dma_init(void)
     dma_chn_mask = ~NU_PDMA_CH_Msk;
     memset(dma_chn_arr, 0x00, sizeof (dma_chn_arr));
 
-    /* Reset module */
-    SYS_ResetModule(dma_modinit.rsetidx);
-
     /* Enable IP clock */
     CLK_EnableModuleClock(dma_modinit.clkidx);
 
+    /* Reset module */
+    SYS_ResetModule(dma_modinit.rsetidx);
+
     PDMA_T *pdma_base = dma_modbase();
 
     PDMA_Open(pdma_base, 0);
diff --git a/targets/TARGET_NUVOTON/TARGET_M251/i2c_api.c b/targets/TARGET_NUVOTON/TARGET_M251/i2c_api.c
index d91b77b35f..bf82c12a6b 100644
--- a/targets/TARGET_NUVOTON/TARGET_M251/i2c_api.c
+++ b/targets/TARGET_NUVOTON/TARGET_M251/i2c_api.c
@@ -98,14 +98,14 @@ void i2c_init(i2c_t *obj, PinName sda, PinName scl)
     MBED_ASSERT(modinit != NULL);
     MBED_ASSERT(modinit->modname == (int) obj->i2c.i2c);
 
-    // Reset this module
-    SYS_ResetModule(modinit->rsetidx);
+    pinmap_pinout(sda, PinMap_I2C_SDA);
+    pinmap_pinout(scl, PinMap_I2C_SCL);
 
     // Enable IP clock
     CLK_EnableModuleClock(modinit->clkidx);
 
-    pinmap_pinout(sda, PinMap_I2C_SDA);
-    pinmap_pinout(scl, PinMap_I2C_SCL);
+    // Reset this module
+    SYS_ResetModule(modinit->rsetidx);
 
 #if DEVICE_I2C_ASYNCH
     obj->i2c.dma_usage = DMA_USAGE_NEVER;
diff --git a/targets/TARGET_NUVOTON/TARGET_M251/lp_ticker.c b/targets/TARGET_NUVOTON/TARGET_M251/lp_ticker.c
index ffa7fb4037..c05d1054ba 100644
--- a/targets/TARGET_NUVOTON/TARGET_M251/lp_ticker.c
+++ b/targets/TARGET_NUVOTON/TARGET_M251/lp_ticker.c
@@ -82,15 +82,15 @@ void lp_ticker_init(void)
     }
     ticker_inited = 1;
 
-    // Reset module
-    SYS_ResetModule(TIMER_MODINIT.rsetidx);
-
     // Select IP clock source
     CLK_SetModuleClock(TIMER_MODINIT.clkidx, TIMER_MODINIT.clksrc, TIMER_MODINIT.clkdiv);
 
     // Enable IP clock
     CLK_EnableModuleClock(TIMER_MODINIT.clkidx);
 
+    // Reset module
+    SYS_ResetModule(TIMER_MODINIT.rsetidx);
+
     TIMER_T *timer_base = (TIMER_T *) NU_MODBASE(TIMER_MODINIT.modname);
 
     // Configure clock
diff --git a/targets/TARGET_NUVOTON/TARGET_M251/pwmout_api.c b/targets/TARGET_NUVOTON/TARGET_M251/pwmout_api.c
index da09a7ff3b..0b489d1caa 100644
--- a/targets/TARGET_NUVOTON/TARGET_M251/pwmout_api.c
+++ b/targets/TARGET_NUVOTON/TARGET_M251/pwmout_api.c
@@ -70,11 +70,8 @@ void pwmout_init(pwmout_t* obj, PinName pin)
     MBED_ASSERT(modinit != NULL);
     MBED_ASSERT(modinit->modname == (int) obj->pwm);
 
-    // NOTE: All channels (identified by PWMName) share a PWM module. This reset will also affect other channels of the same PWM module.
-    if (! ((struct nu_pwm_var *) modinit->var)->en_msk) {
-        // Reset this module if no channel enabled
-        SYS_ResetModule(modinit->rsetidx);
-    }
+    // Wire pinout
+    pinmap_pinout(pin, PinMap_PWM);
 
     uint32_t chn =  NU_MODSUBINDEX(obj->pwm);
 
@@ -86,8 +83,11 @@ void pwmout_init(pwmout_t* obj, PinName pin)
         CLK_EnableModuleClock(modinit->clkidx);
     }
 
-    // Wire pinout
-    pinmap_pinout(pin, PinMap_PWM);
+    // NOTE: All channels (identified by PWMName) share a PWM module. This reset will also affect other channels of the same PWM module.
+    if (! ((struct nu_pwm_var *) modinit->var)->en_msk) {
+        // Reset this module if no channel enabled
+        SYS_ResetModule(modinit->rsetidx);
+    }
 
     // Default: period = 10 ms, pulse width = 0 ms
     obj->period_us = 1000 * 10;
diff --git a/targets/TARGET_NUVOTON/TARGET_M251/serial_api.c b/targets/TARGET_NUVOTON/TARGET_M251/serial_api.c
index fab0bf5850..971b2e6158 100644
--- a/targets/TARGET_NUVOTON/TARGET_M251/serial_api.c
+++ b/targets/TARGET_NUVOTON/TARGET_M251/serial_api.c
@@ -156,16 +156,16 @@ void serial_init(serial_t *obj, PinName tx, PinName rx)
     struct nu_uart_var *var = (struct nu_uart_var *) modinit->var;
 
     if (! var->ref_cnt) {
-        // Reset this module
-        SYS_ResetModule(modinit->rsetidx);
+        pinmap_pinout(tx, PinMap_UART_TX);
+        pinmap_pinout(rx, PinMap_UART_RX);
 
         // Select IP clock source
         CLK_SetModuleClock(modinit->clkidx, modinit->clksrc, modinit->clkdiv);
         // Enable IP clock
         CLK_EnableModuleClock(modinit->clkidx);
 
-        pinmap_pinout(tx, PinMap_UART_TX);
-        pinmap_pinout(rx, PinMap_UART_RX);
+        // Reset this module
+        SYS_ResetModule(modinit->rsetidx);
 
         // Configure baudrate
         int baudrate = 9600;
diff --git a/targets/TARGET_NUVOTON/TARGET_M251/spi_api.c b/targets/TARGET_NUVOTON/TARGET_M251/spi_api.c
index 0e5d5cad80..a72ae85a82 100644
--- a/targets/TARGET_NUVOTON/TARGET_M251/spi_api.c
+++ b/targets/TARGET_NUVOTON/TARGET_M251/spi_api.c
@@ -120,18 +120,18 @@ void spi_init(spi_t *obj, PinName mosi, PinName miso, PinName sclk, PinName ssel
     MBED_ASSERT(modinit != NULL);
     MBED_ASSERT(modinit->modname == (int) obj->spi.spi);
 
-    // Reset this module
-    SYS_ResetModule(modinit->rsetidx);
+    pinmap_pinout(mosi, PinMap_SPI_MOSI);
+    pinmap_pinout(miso, PinMap_SPI_MISO);
+    pinmap_pinout(sclk, PinMap_SPI_SCLK);
+    pinmap_pinout(ssel, PinMap_SPI_SSEL);
 
     // Select IP clock source
     CLK_SetModuleClock(modinit->clkidx, modinit->clksrc, modinit->clkdiv);
     // Enable IP clock
     CLK_EnableModuleClock(modinit->clkidx);
 
-    pinmap_pinout(mosi, PinMap_SPI_MOSI);
-    pinmap_pinout(miso, PinMap_SPI_MISO);
-    pinmap_pinout(sclk, PinMap_SPI_SCLK);
-    pinmap_pinout(ssel, PinMap_SPI_SSEL);
+    // Reset this module
+    SYS_ResetModule(modinit->rsetidx);
 
     obj->spi.pin_mosi = mosi;
     obj->spi.pin_miso = miso;
diff --git a/targets/TARGET_NUVOTON/TARGET_M251/us_ticker.c b/targets/TARGET_NUVOTON/TARGET_M251/us_ticker.c
index 358fe2832d..8aeca00bbe 100644
--- a/targets/TARGET_NUVOTON/TARGET_M251/us_ticker.c
+++ b/targets/TARGET_NUVOTON/TARGET_M251/us_ticker.c
@@ -58,15 +58,15 @@ void us_ticker_init(void)
     }
     ticker_inited = 1;
 
-    // Reset IP
-    SYS_ResetModule(TIMER_MODINIT.rsetidx);
-
     // Select IP clock source
     CLK_SetModuleClock(TIMER_MODINIT.clkidx, TIMER_MODINIT.clksrc, TIMER_MODINIT.clkdiv);
 
     // Enable IP clock
     CLK_EnableModuleClock(TIMER_MODINIT.clkidx);
 
+    // Reset IP
+    SYS_ResetModule(TIMER_MODINIT.rsetidx);
+
     TIMER_T *timer_base = (TIMER_T *) NU_MODBASE(TIMER_MODINIT.modname);
 
     // Timer for normal counter