Porting of new target: Added new target to target.py, added header files for PinNames.h and device.h

nRF51822 from Nordic Semiconductor

Bluetooth Low-Energy v4.1 compliant - interface to smartphones, tablets

System-on-Chip (SoC) solution - easily transformable into a deployable solution

Drop-in solution for production - no need to design your own antenna

FCC and CE Certified

3x LEDs, 3x Buttons

Powered by interface board or external 3.3V

libraries/mbed/targets/hal/TARGET_NORDIC/TARGET_MCU_NRF51822/TARGET_NRF51822_Y5_MBUG/PinNames.h

@@ -0,0 +1,150 @@
+/* mbed Microcontroller Library
+ * Copyright (c) 2013 Nordic Semiconductor
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+#ifndef MBED_PINNAMES_H
+#define MBED_PINNAMES_H
+
+#include "cmsis.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+typedef enum {
+    PIN_INPUT,
+    PIN_OUTPUT
+} PinDirection;
+
+#define PORT_SHIFT  3
+
+typedef enum {
+    p0  = 0,
+    p1  = 1,
+    p2  = 2,
+    p3  = 3,
+    p4  = 4,
+    p5  = 5,
+    p6  = 6,
+    p7  = 7,
+    p8  = 8,
+    p9  = 9,
+    p10 = 10,
+    p11 = 11,
+    p12 = 12,
+    p13 = 13,
+    p14 = 14,
+    p15 = 15,
+    p16 = 16,
+    p17 = 17,
+    p18 = 18,
+    p19 = 19,
+    p20 = 20,
+    p21 = 21,
+    p22 = 22,
+    p23 = 23,
+    p24 = 24,
+    p25 = 25,
+    p26 = 26,
+    p27 = 27,
+    p28 = 28,
+    p29 = 29,
+    p30 = 30,
+	p31 = 31,
+	p32 = 32,
+	p33 = 33,
+	p34 = 34,
+	p35 = 35,
+//    p31=31,    
+
+    // Not connected
+    NC = (int)0xFFFFFFFF,
+
+    
+    P0_0  = p0,
+    P0_1  = p1,
+    P0_2  = p2,
+    P0_3  = p3,
+    P0_4  = p4,
+    P0_5  = p5,
+    P0_6  = p6,
+    P0_7  = p7,
+    
+    P0_8  = p8,
+    P0_9  = p9,
+    P0_10 = p10,
+    P0_11 = p11,
+    P0_12 = p12,
+    P0_13 = p13,
+    P0_14 = p14,
+    P0_15 = p15,
+    
+    P0_16 = p16,
+    P0_17 = p17,
+    P0_18 = p18,
+    P0_19 = p19,
+    P0_20 = p20,
+    P0_21 = p21,
+    P0_22 = p22,
+    P0_23 = p23,
+    
+    P0_24 = p24,
+    P0_25 = p25,
+    P0_26 = p26,
+    P0_27 = p27,
+    P0_28 = p28,
+    P0_29 = p29,
+    P0_30 = p30,
+    
+	LED		= p30,
+    LED1    = p30,
+    LED2    = p0,
+    LED3    = p8,
+    LED4    = NC,
+    
+    BUTTON1 = p29,
+    BUTTON2 = p17,
+	
+        	
+    RX_PIN_NUMBER = p2,
+    TX_PIN_NUMBER = p3,
+    CTS_PIN_NUMBER = p11,
+    RTS_PIN_NUMBER = p21,
+
+    // mBed interface Pins
+    USBTX = TX_PIN_NUMBER,
+    USBRX = RX_PIN_NUMBER,
+        
+    SPIS_PSELMOSI = p12,
+    SPIS_PSELMISO = p6,
+    SPIS_PSELSCK = p9,
+
+    I2C_SDA0 = p17,
+    I2C_SCL0 = p18,
+
+  
+} PinName;
+
+typedef enum {
+    PullNone = 0,
+    PullDown = 1,
+    PullUp = 3,
+    PullDefault = PullUp
+} PinMode;
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif

libraries/mbed/targets/hal/TARGET_NORDIC/TARGET_MCU_NRF51822/TARGET_NRF51822_Y5_MBUG/device.h

@@ -0,0 +1,57 @@
+/* mbed Microcontroller Library
+ * Copyright (c) 2006-2013 ARM Limited
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+#ifndef MBED_DEVICE_H
+#define MBED_DEVICE_H
+
+#define DEVICE_PORTIN           1
+#define DEVICE_PORTOUT          1
+#define DEVICE_PORTINOUT        1
+
+#define DEVICE_INTERRUPTIN      1
+
+#define DEVICE_ANALOGIN         1
+#define DEVICE_ANALOGOUT        0
+
+#define DEVICE_SERIAL           1
+
+#define DEVICE_I2C              1
+#define DEVICE_I2CSLAVE         0
+
+#define DEVICE_SPI              1
+#define DEVICE_SPISLAVE         1
+
+#define DEVICE_CAN              0
+
+#define DEVICE_RTC              0
+
+#define DEVICE_ETHERNET         0
+
+#define DEVICE_PWMOUT           1
+
+#define DEVICE_SEMIHOST         0
+#define DEVICE_LOCALFILESYSTEM  0
+
+#define DEVICE_SLEEP            1
+
+#define DEVICE_DEBUG_AWARENESS  0
+
+#define DEVICE_STDIO_MESSAGES   0
+
+#define DEVICE_ERROR_PATTERN    1
+
+#include "objects.h"
+
+#endif

workspace_tools/targets.py

@@ -750,6 +750,12 @@ class RBLAB_BLENANO(NRF51822):
         self.extra_labels = ['NORDIC', 'MCU_NRF51822', 'MCU_NORDIC_16K']
         self.macros = ['TARGET_NRF51822']
 
+class NRF51822_Y5_MBUG(NRF51822):
+    def __init__(self):
+        NRF51822.__init__(self)
+        self.extra_labels = ['NORDIC', 'MCU_NRF51822', 'MCU_NORDIC_16K']
+        self.macros = ['TARGET_NRF51822']
+
 class XADOW_M0(LPCTarget):
     def __init__(self):
         LPCTarget.__init__(self)
@@ -868,6 +874,7 @@ TARGETS = [
     HRM1017(),      # nRF51822
     RBLAB_NRF51822(),# nRF51822
     RBLAB_BLENANO(),# nRF51822
+	NRF51822_Y5_MBUG(),#nRF51822
     XADOW_M0(),     # nRF51822
     WALLBOT_BLE(),  # nRF51822