mirror of https://github.com/ARMmbed/mbed-os.git
[NUCLEO_F746ZG] fix pins and system files after manual and automatic test phase
parent
1ecd69bd87
commit
3b3f89294e
|
@ -84,7 +84,7 @@
|
|||
HAL_StatusTypeDef HAL_Init(void);
|
||||
|
||||
#if !defined (HSE_VALUE)
|
||||
#define HSE_VALUE ((uint32_t)25000000) /*!< Default value of the External oscillator in Hz */
|
||||
#define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
|
||||
#endif /* HSE_VALUE */
|
||||
|
||||
#if !defined (HSI_VALUE)
|
||||
|
@ -108,15 +108,6 @@ HAL_StatusTypeDef HAL_Init(void);
|
|||
*/
|
||||
|
||||
/************************* Miscellaneous Configuration ************************/
|
||||
/*!< Uncomment the following line if you need to use external SRAM or SDRAM mounted
|
||||
on EVAL board as data memory */
|
||||
/* #define DATA_IN_ExtSRAM */
|
||||
/* #define DATA_IN_ExtSDRAM */
|
||||
|
||||
#if defined(DATA_IN_ExtSRAM) && defined(DATA_IN_ExtSDRAM)
|
||||
#error "Please select DATA_IN_ExtSRAM or DATA_IN_ExtSDRAM "
|
||||
#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
|
||||
|
||||
/*!< Uncomment the following line if you need to relocate your vector Table in
|
||||
Internal SRAM. */
|
||||
/* #define VECT_TAB_SRAM */
|
||||
|
@ -133,7 +124,7 @@ HAL_StatusTypeDef HAL_Init(void);
|
|||
*/
|
||||
|
||||
/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
|
||||
#define USE_PLL_HSE_EXTC (1) /* Use external clock --> NOT USED ON THIS BOARD */
|
||||
#define USE_PLL_HSE_EXTC (1) /* Use external clock */
|
||||
#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
|
||||
|
||||
/**
|
||||
|
@ -162,10 +153,6 @@ const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8,
|
|||
/** @addtogroup STM32F7xx_System_Private_FunctionPrototypes
|
||||
* @{
|
||||
*/
|
||||
#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
|
||||
static void SystemInit_ExtMemCtl(void);
|
||||
#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
|
||||
|
||||
#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
|
||||
uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
|
||||
#endif
|
||||
|
@ -212,10 +199,6 @@ void SystemInit(void)
|
|||
/* Disable all interrupts */
|
||||
RCC->CIR = 0x00000000;
|
||||
|
||||
#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
|
||||
SystemInit_ExtMemCtl();
|
||||
#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
|
||||
|
||||
/* Configure the Vector Table location add offset address ------------------*/
|
||||
#ifdef VECT_TAB_SRAM
|
||||
SCB->VTOR = SRAM1_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
|
||||
|
@ -324,231 +307,6 @@ void SystemCoreClockUpdate(void)
|
|||
SystemCoreClock >>= tmp;
|
||||
}
|
||||
|
||||
#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
|
||||
/**
|
||||
* @brief Setup the external memory controller.
|
||||
* Called in startup_stm32f7xx.s before jump to main.
|
||||
* This function configures the external memories (SRAM/SDRAM)
|
||||
* This SRAM/SDRAM will be used as program data memory (including heap and stack).
|
||||
* @param None
|
||||
* @retval None
|
||||
*/
|
||||
void SystemInit_ExtMemCtl(void)
|
||||
{
|
||||
__IO uint32_t tmp = 0;
|
||||
#if defined (DATA_IN_ExtSDRAM)
|
||||
register uint32_t tmpreg = 0, timeout = 0xFFFF;
|
||||
register uint32_t index;
|
||||
|
||||
/* Enable GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
|
||||
clock */
|
||||
RCC->AHB1ENR |= 0x000001F8;
|
||||
|
||||
/* Delay after an RCC peripheral clock enabling */
|
||||
tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);
|
||||
|
||||
/* Connect PDx pins to FMC Alternate function */
|
||||
GPIOD->AFR[0] = 0x000000CC;
|
||||
GPIOD->AFR[1] = 0xCC000CCC;
|
||||
/* Configure PDx pins in Alternate function mode */
|
||||
GPIOD->MODER = 0xA02A000A;
|
||||
/* Configure PDx pins speed to 50 MHz */
|
||||
GPIOD->OSPEEDR = 0xA02A000A;
|
||||
/* Configure PDx pins Output type to push-pull */
|
||||
GPIOD->OTYPER = 0x00000000;
|
||||
/* No pull-up, pull-down for PDx pins */
|
||||
GPIOD->PUPDR = 0x50150005;
|
||||
|
||||
/* Connect PEx pins to FMC Alternate function */
|
||||
GPIOE->AFR[0] = 0xC00000CC;
|
||||
GPIOE->AFR[1] = 0xCCCCCCCC;
|
||||
/* Configure PEx pins in Alternate function mode */
|
||||
GPIOE->MODER = 0xAAAA800A;
|
||||
/* Configure PEx pins speed to 50 MHz */
|
||||
GPIOE->OSPEEDR = 0xAAAA800A;
|
||||
/* Configure PEx pins Output type to push-pull */
|
||||
GPIOE->OTYPER = 0x00000000;
|
||||
/* No pull-up, pull-down for PEx pins */
|
||||
GPIOE->PUPDR = 0x55554005;
|
||||
|
||||
/* Connect PFx pins to FMC Alternate function */
|
||||
GPIOF->AFR[0] = 0x00CCCCCC;
|
||||
GPIOF->AFR[1] = 0xCCCCC000;
|
||||
/* Configure PFx pins in Alternate function mode */
|
||||
GPIOF->MODER = 0xAA800AAA;
|
||||
/* Configure PFx pins speed to 50 MHz */
|
||||
GPIOF->OSPEEDR = 0xAA800AAA;
|
||||
/* Configure PFx pins Output type to push-pull */
|
||||
GPIOF->OTYPER = 0x00000000;
|
||||
/* No pull-up, pull-down for PFx pins */
|
||||
GPIOF->PUPDR = 0x55400555;
|
||||
|
||||
/* Connect PGx pins to FMC Alternate function */
|
||||
GPIOG->AFR[0] = 0x00CC00CC;
|
||||
GPIOG->AFR[1] = 0xC000000C;
|
||||
/* Configure PGx pins in Alternate function mode */
|
||||
GPIOG->MODER = 0x80020A0A;
|
||||
/* Configure PGx pins speed to 50 MHz */
|
||||
GPIOG->OSPEEDR = 0x80020A0A;
|
||||
/* Configure PGx pins Output type to push-pull */
|
||||
GPIOG->OTYPER = 0x00000000;
|
||||
/* No pull-up, pull-down for PGx pins */
|
||||
GPIOG->PUPDR = 0x40010505;
|
||||
|
||||
/* Connect PHx pins to FMC Alternate function */
|
||||
GPIOH->AFR[0] = 0x00C0CC00;
|
||||
GPIOH->AFR[1] = 0xCCCCCCCC;
|
||||
/* Configure PHx pins in Alternate function mode */
|
||||
GPIOH->MODER = 0xAAAA08A0;
|
||||
/* Configure PHx pins speed to 50 MHz */
|
||||
GPIOH->OSPEEDR = 0xAAAA08A0;
|
||||
/* Configure PHx pins Output type to push-pull */
|
||||
GPIOH->OTYPER = 0x00000000;
|
||||
/* No pull-up, pull-down for PHx pins */
|
||||
GPIOH->PUPDR = 0x55550450;
|
||||
|
||||
/* Connect PIx pins to FMC Alternate function */
|
||||
GPIOI->AFR[0] = 0xCCCCCCCC;
|
||||
GPIOI->AFR[1] = 0x00000CC0;
|
||||
/* Configure PIx pins in Alternate function mode */
|
||||
GPIOI->MODER = 0x0028AAAA;
|
||||
/* Configure PIx pins speed to 50 MHz */
|
||||
GPIOI->OSPEEDR = 0x0028AAAA;
|
||||
/* Configure PIx pins Output type to push-pull */
|
||||
GPIOI->OTYPER = 0x00000000;
|
||||
/* No pull-up, pull-down for PIx pins */
|
||||
GPIOI->PUPDR = 0x00145555;
|
||||
|
||||
/*-- FMC Configuration ------------------------------------------------------*/
|
||||
/* Enable the FMC interface clock */
|
||||
RCC->AHB3ENR |= 0x00000001;
|
||||
|
||||
/* Delay after an RCC peripheral clock enabling */
|
||||
tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
|
||||
|
||||
/* Configure and enable SDRAM bank1 */
|
||||
FMC_Bank5_6->SDCR[0] = 0x000019E5;
|
||||
FMC_Bank5_6->SDTR[0] = 0x01116361;
|
||||
|
||||
/* SDRAM initialization sequence */
|
||||
/* Clock enable command */
|
||||
FMC_Bank5_6->SDCMR = 0x00000011;
|
||||
tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
|
||||
while((tmpreg != 0) && (timeout-- > 0))
|
||||
{
|
||||
tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
|
||||
}
|
||||
|
||||
/* Delay */
|
||||
for (index = 0; index<1000; index++);
|
||||
|
||||
/* PALL command */
|
||||
FMC_Bank5_6->SDCMR = 0x00000012;
|
||||
timeout = 0xFFFF;
|
||||
while((tmpreg != 0) && (timeout-- > 0))
|
||||
{
|
||||
tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
|
||||
}
|
||||
|
||||
/* Auto refresh command */
|
||||
FMC_Bank5_6->SDCMR = 0x000000F3;
|
||||
timeout = 0xFFFF;
|
||||
while((tmpreg != 0) && (timeout-- > 0))
|
||||
{
|
||||
tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
|
||||
}
|
||||
|
||||
/* MRD register program */
|
||||
FMC_Bank5_6->SDCMR = 0x00046014;
|
||||
timeout = 0xFFFF;
|
||||
while((tmpreg != 0) && (timeout-- > 0))
|
||||
{
|
||||
tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
|
||||
}
|
||||
|
||||
/* Set refresh count */
|
||||
tmpreg = FMC_Bank5_6->SDRTR;
|
||||
FMC_Bank5_6->SDRTR = (tmpreg | (0x00000603<<1));
|
||||
|
||||
/* Disable write protection */
|
||||
tmpreg = FMC_Bank5_6->SDCR[0];
|
||||
FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
|
||||
#endif /* DATA_IN_ExtSDRAM */
|
||||
|
||||
#if defined(DATA_IN_ExtSRAM)
|
||||
/*-- GPIOs Configuration -----------------------------------------------------*/
|
||||
/* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
|
||||
RCC->AHB1ENR |= 0x00000078;
|
||||
|
||||
/* Delay after an RCC peripheral clock enabling */
|
||||
tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);
|
||||
|
||||
/* Connect PDx pins to FMC Alternate function */
|
||||
GPIOD->AFR[0] = 0x00CCC0CC;
|
||||
GPIOD->AFR[1] = 0xCCCCCCCC;
|
||||
/* Configure PDx pins in Alternate function mode */
|
||||
GPIOD->MODER = 0xAAAA0A8A;
|
||||
/* Configure PDx pins speed to 100 MHz */
|
||||
GPIOD->OSPEEDR = 0xFFFF0FCF;
|
||||
/* Configure PDx pins Output type to push-pull */
|
||||
GPIOD->OTYPER = 0x00000000;
|
||||
/* No pull-up, pull-down for PDx pins */
|
||||
GPIOD->PUPDR = 0x55550545;
|
||||
|
||||
/* Connect PEx pins to FMC Alternate function */
|
||||
GPIOE->AFR[0] = 0xC00CC0CC;
|
||||
GPIOE->AFR[1] = 0xCCCCCCCC;
|
||||
/* Configure PEx pins in Alternate function mode */
|
||||
GPIOE->MODER = 0xAAAA828A;
|
||||
/* Configure PEx pins speed to 100 MHz */
|
||||
GPIOE->OSPEEDR = 0xFFFFC3CF;
|
||||
/* Configure PEx pins Output type to push-pull */
|
||||
GPIOE->OTYPER = 0x00000000;
|
||||
/* No pull-up, pull-down for PEx pins */
|
||||
GPIOE->PUPDR = 0x55554145;
|
||||
|
||||
/* Connect PFx pins to FMC Alternate function */
|
||||
GPIOF->AFR[0] = 0x00CCCCCC;
|
||||
GPIOF->AFR[1] = 0xCCCC0000;
|
||||
/* Configure PFx pins in Alternate function mode */
|
||||
GPIOF->MODER = 0xAA000AAA;
|
||||
/* Configure PFx pins speed to 100 MHz */
|
||||
GPIOF->OSPEEDR = 0xFF000FFF;
|
||||
/* Configure PFx pins Output type to push-pull */
|
||||
GPIOF->OTYPER = 0x00000000;
|
||||
/* No pull-up, pull-down for PFx pins */
|
||||
GPIOF->PUPDR = 0x55000555;
|
||||
|
||||
/* Connect PGx pins to FMC Alternate function */
|
||||
GPIOG->AFR[0] = 0x00CCCCCC;
|
||||
GPIOG->AFR[1] = 0x000000C0;
|
||||
/* Configure PGx pins in Alternate function mode */
|
||||
GPIOG->MODER = 0x00200AAA;
|
||||
/* Configure PGx pins speed to 100 MHz */
|
||||
GPIOG->OSPEEDR = 0x00300FFF;
|
||||
/* Configure PGx pins Output type to push-pull */
|
||||
GPIOG->OTYPER = 0x00000000;
|
||||
/* No pull-up, pull-down for PGx pins */
|
||||
GPIOG->PUPDR = 0x00100555;
|
||||
|
||||
/*-- FMC/FSMC Configuration --------------------------------------------------*/
|
||||
/* Enable the FMC/FSMC interface clock */
|
||||
RCC->AHB3ENR |= 0x00000001;
|
||||
|
||||
/* Delay after an RCC peripheral clock enabling */
|
||||
tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
|
||||
|
||||
/* Configure and enable Bank1_SRAM2 */
|
||||
FMC_Bank1->BTCR[4] = 0x00001091;
|
||||
FMC_Bank1->BTCR[5] = 0x00110212;
|
||||
FMC_Bank1E->BWTR[4] = 0x0FFFFFFF;
|
||||
|
||||
#endif /* DATA_IN_ExtSRAM */
|
||||
|
||||
(void)(tmp);
|
||||
}
|
||||
#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
|
||||
|
||||
/**
|
||||
* @brief Configures the System clock source, PLL Multiplier and Divider factors,
|
||||
* AHB/APBx prescalers and Flash settings
|
||||
|
@ -581,7 +339,7 @@ void SetSysClock(void)
|
|||
}
|
||||
|
||||
// Output clock on MCO2 pin(PC9) for debugging purpose
|
||||
// Can be visualized on uSD card CN3 connector pin 8
|
||||
// Can be visualized on CN8 connector pin 4
|
||||
//HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 216 MHz / 4 = 54 MHz
|
||||
}
|
||||
|
||||
|
|
|
@ -44,7 +44,7 @@ const PinMap PinMap_ADC[] = {
|
|||
{PA_0, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 - ARDUINO A0
|
||||
// {PA_1, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 (used by ethernet)
|
||||
// {PA_2, ADC_1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 (used by ethernet)
|
||||
{PA_3, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2
|
||||
{PA_3, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN2
|
||||
{PA_4, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4
|
||||
{PA_5, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 - ARDUINO D13
|
||||
{PA_6, ADC_2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6 - ARDUINO D12
|
||||
|
@ -119,10 +119,10 @@ const PinMap PinMap_PWM[] = {
|
|||
// {PA_5, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N
|
||||
{PA_6, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
|
||||
// {PA_6, PWM_13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1
|
||||
{PA_7, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N (remove JP6 to use it)
|
||||
// {PA_7, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 (remove JP6 to use it)
|
||||
// {PA_7, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N (remove JP6 to use it)
|
||||
// {PA_7, PWM_14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1 (remove JP6 to use it)
|
||||
// {PA_7, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N (used by ethernet)
|
||||
// {PA_7, PWM_3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 (used by ethernet)
|
||||
// {PA_7, PWM_8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N (used by ethernet)
|
||||
// {PA_7, PWM_14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1 (used by ethernet)
|
||||
{PA_8, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
|
||||
// {PA_9, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 (used by USB)
|
||||
// {PA_10, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 (used by USB)
|
||||
|
@ -176,6 +176,7 @@ const PinMap PinMap_PWM[] = {
|
|||
{PE_11, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
|
||||
{PE_12, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
|
||||
{PE_13, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
|
||||
{PE_14, PWM_1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4
|
||||
|
||||
{PF_6, PWM_10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1
|
||||
{PF_7, PWM_11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1
|
||||
|
@ -214,8 +215,8 @@ const PinMap PinMap_UART_RX[] = {
|
|||
// {PB_7, UART_1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, // (used by LED2)
|
||||
{PB_11, UART_3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
{PC_7, UART_6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
|
||||
{PC_11, UART_3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
// {PC_11, UART_4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
||||
// {PC_11, UART_3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
{PC_11, UART_4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
||||
{PD_2, UART_5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART5)},
|
||||
{PD_6, UART_2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
{PD_9, UART_3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, // STDIO_RX
|
||||
|
|
Loading…
Reference in New Issue