diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_DRAGONFLY_F411RE/device/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_DRAGONFLY_F411RE/device/system_clock.c
new file mode 100644
index 0000000000..6fe069502b
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_DRAGONFLY_F411RE/device/system_clock.c
@@ -0,0 +1,245 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
+ * | (external 8 MHz clock) | (internal 16 MHz)
+ * | 2- PLL_HSE_XTAL |
+ * | (external 8 MHz xtal) |
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 100 | 100
+ *-----------------------------------------------------------------------------
+ * AHBCLK (MHz) | 100 | 100
+ *-----------------------------------------------------------------------------
+ * APB1CLK (MHz) | 50 | 50
+ *-----------------------------------------------------------------------------
+ * APB2CLK (MHz) | 100 | 100
+ *-----------------------------------------------------------------------------
+ * USB capable (48 MHz precise clock) | NO | NO
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#ifndef VECT_TAB_OFFSET
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+#endif
+
+
+/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
+#define USE_PLL_HSE_EXTC (0) /* Use external clock */
+#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif
+
+uint8_t SetSysClock_PLL_HSI(void);
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+void SetSysClock(void)
+{
+ /* 1- Try to start with HSE and external clock */
+#if USE_PLL_HSE_EXTC != 0
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+ /* 2- If fail try to start with HSE and external xtal */
+#if USE_PLL_HSE_XTAL != 0
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0) {
+ while(1) {
+ // [TODO] Put something here to tell the user that a problem occured...
+ }
+ }
+ }
+ }
+
+ /* Output clock on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 100 MHz / 4 = 25 MHz
+}
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSE oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
+ }
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ //RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
+ //RCC_OscInitStruct.PLL.PLLN = 400; // VCO output clock = 400 MHz (1 MHz * 400)
+ RCC_OscInitStruct.PLL.PLLM = 13; // VCO input clock = 2 MHz (8 MHz / 4)
+ RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 400 MHz (2 MHz * 200)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 100 MHz (400 MHz / 4)
+ RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 44.44 MHz (400 MHz / 9) --> Not good for USB
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 100 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 100 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 50 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 100 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+
+ //if (bypass == 0)
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
+ //else
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
+
+ return 1; // OK
+}
+#endif
+
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSI oscillator and activate PLL with HSI as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ //RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ //RCC_OscInitStruct.PLL.PLLN = 400; // VCO output clock = 400 MHz (1 MHz * 400)
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 2 MHz (16 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 200; // VCO output clock = 400 MHz (2 MHz * 200)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 100 MHz (400 MHz / 4)
+ RCC_OscInitStruct.PLL.PLLQ = 9; // USB clock = 44.44 MHz (400 MHz / 9) --> Not good for USB
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 100 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 100 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 50 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 100 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+ return 1; // OK
+}
+
+/******************************************************************************/
+/* Hard Fault Handler */
+/******************************************************************************/
+void HardFault_Handler(void)
+{
+ printf("Hard Fault\n");
+ NVIC_SystemReset();
+}
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_DRAGONFLY_F411RE/device/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_DRAGONFLY_F411RE/device/system_stm32f4xx.c
deleted file mode 100644
index 8d8219422f..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_DRAGONFLY_F411RE/device/system_stm32f4xx.c
+++ /dev/null
@@ -1,946 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.5.0
- * @date 22-April-2016
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 100 | 100
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 100 | 100
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 50 | 50
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 100 | 100
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | NO | NO
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2016 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#ifndef VECT_TAB_OFFSET
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-#endif
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (0) /* Use external clock */
-#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 16000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
- defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- /* Output clock on MCO2 pin(PC9) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 100 MHz / 4 = 25 MHz
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSE oscillator and activate PLL with HSE as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
- }
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- //RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- //RCC_OscInitStruct.PLL.PLLN = 400; // VCO output clock = 400 MHz (1 MHz * 400)
- RCC_OscInitStruct.PLL.PLLM = 13; // VCO input clock = 2 MHz (8 MHz / 4)
- RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 400 MHz (2 MHz * 200)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 100 MHz (400 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 44.44 MHz (400 MHz / 9) --> Not good for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 100 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 100 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 50 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 100 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
-
- //if (bypass == 0)
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
- //else
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSI oscillator and activate PLL with HSI as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- //RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- //RCC_OscInitStruct.PLL.PLLN = 400; // VCO output clock = 400 MHz (1 MHz * 400)
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 2 MHz (16 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 200; // VCO output clock = 400 MHz (2 MHz * 200)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 100 MHz (400 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 9; // USB clock = 44.44 MHz (400 MHz / 9) --> Not good for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 100 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 100 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 50 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 100 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-
- return 1; // OK
-}
-
-/******************************************************************************/
-/* Hard Fault Handler */
-/******************************************************************************/
-void HardFault_Handler(void)
-{
- printf("Hard Fault\n");
- NVIC_SystemReset();
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F405RG/device/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F405RG/device/system_clock.c
new file mode 100644
index 0000000000..5b7b040a9e
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F405RG/device/system_clock.c
@@ -0,0 +1,105 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+#include "stm32f4xx.h"
+
+
+/**
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+void SetSysClock(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 26;
+ RCC_OscInitStruct.PLL.PLLN = 192;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4;
+ RCC_OscInitStruct.PLL.PLLQ = 4;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
+}
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F411RE/device/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F411RE/device/system_clock.c
new file mode 100644
index 0000000000..196b2e15af
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F411RE/device/system_clock.c
@@ -0,0 +1,248 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
+ * | (external 8 MHz clock) | (internal 16 MHz)
+ * | 2- PLL_HSE_XTAL |
+ * | (external 8 MHz xtal) |
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 96 | 96
+ *-----------------------------------------------------------------------------
+ * AHBCLK (MHz) | 96 | 96
+ *-----------------------------------------------------------------------------
+ * APB1CLK (MHz) | 48 | 48
+ *-----------------------------------------------------------------------------
+ * APB2CLK (MHz) | 96 | 96
+ *-----------------------------------------------------------------------------
+ * USB capable (48 MHz precise clock) | YES | NO
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#ifndef VECT_TAB_OFFSET
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+#endif
+
+
+/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
+#if !defined (USE_PLL_HSE_EXTC)
+#define USE_PLL_HSE_EXTC (1) /* Use external clock */
+#endif
+#if !defined (USE_PLL_HSE_XTAL)
+#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
+#endif
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif
+
+uint8_t SetSysClock_PLL_HSI(void);
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+void SetSysClock(void)
+{
+ /* 1- Try to start with HSE and external clock */
+#if USE_PLL_HSE_EXTC != 0
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+ /* 2- If fail try to start with HSE and external xtal */
+#if USE_PLL_HSE_XTAL != 0
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0) {
+ while(1) {
+ // [TODO] Put something here to tell the user that a problem occured...
+ }
+ }
+ }
+ }
+
+ /* Output clock on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 100 MHz / 4 = 25 MHz
+}
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSE oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
+ }
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; // VCO input clock = 1 MHz
+ RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 192 MHz (1 MHz * 192)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 96 MHz (192 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 4; // USB clock = 48 MHz (192 MHz / 4)
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+
+ //if (bypass == 0)
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
+ //else
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
+
+ return 1; // OK
+}
+#endif
+
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSI oscillator and activate PLL with HSI as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 192 MHz (1 MHz * 192)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 96 MHz (192 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 4; // USB clock = 48 MHz (192 MHz / 4) --> Not stable for USB
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+ return 1; // OK
+}
+
+/******************************************************************************/
+/* Hard Fault Handler */
+/******************************************************************************/
+void HardFault_Handler(void)
+{
+ printf("Hard Fault\n");
+ NVIC_SystemReset();
+}
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F411RE/device/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F411RE/device/system_stm32f4xx.c
deleted file mode 100644
index c9615f162e..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F411RE/device/system_stm32f4xx.c
+++ /dev/null
@@ -1,946 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.5.0
- * @date 22-April-2016
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 96 | 96
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 96 | 96
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 48 | 48
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 96 | 96
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2016 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#ifndef VECT_TAB_OFFSET
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-#endif
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#if !defined (USE_PLL_HSE_EXTC)
- #define USE_PLL_HSE_EXTC (1) /* Use external clock */
-#endif
-#if !defined (USE_PLL_HSE_XTAL)
- #define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-#endif
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 16000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
- defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- /* Output clock on MCO2 pin(PC9) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 100 MHz / 4 = 25 MHz
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSE oscillator and activate PLL with HSE as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
- }
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; // VCO input clock = 1 MHz
- RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 192 MHz (1 MHz * 192)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 96 MHz (192 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 4; // USB clock = 48 MHz (192 MHz / 4)
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
-
- //if (bypass == 0)
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
- //else
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSI oscillator and activate PLL with HSI as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 192 MHz (1 MHz * 192)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 96 MHz (192 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 4; // USB clock = 48 MHz (192 MHz / 4) --> Not stable for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-
- return 1; // OK
-}
-
-/******************************************************************************/
-/* Hard Fault Handler */
-/******************************************************************************/
-void HardFault_Handler(void)
-{
- printf("Hard Fault\n");
- NVIC_SystemReset();
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xC/TARGET_DISCO_F401VC/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xC/TARGET_DISCO_F401VC/system_clock.c
new file mode 100644
index 0000000000..fc35c43496
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xC/TARGET_DISCO_F401VC/system_clock.c
@@ -0,0 +1,231 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
+ * | (external 8 MHz clock) | (internal 16 MHz)
+ * | 2- PLL_HSE_XTAL |
+ * | (external 8 MHz xtal) |
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 84 | 84
+ *-----------------------------------------------------------------------------
+ * AHBCLK (MHz) | 84 | 84
+ *-----------------------------------------------------------------------------
+ * APB1CLK (MHz) | 42 | 42
+ *-----------------------------------------------------------------------------
+ * APB2CLK (MHz) | 84 | 84
+ *-----------------------------------------------------------------------------
+ * USB capable (48 MHz precise clock) | YES | NO
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
+#define USE_PLL_HSE_EXTC (1) /* Use external clock */
+#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif
+
+uint8_t SetSysClock_PLL_HSI(void);
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+void SetSysClock(void)
+{
+ /* 1- Try to start with HSE and external clock */
+#if USE_PLL_HSE_EXTC != 0
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+ /* 2- If fail try to start with HSE and external xtal */
+#if USE_PLL_HSE_XTAL != 0
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0) {
+ while(1) {
+ // [TODO] Put something here to tell the user that a problem occured...
+ }
+ }
+ }
+ }
+
+ /* Output clock on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_1); // 84 MHz
+}
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSE oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
+ }
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4)
+ RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> OK for USB
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 84 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ /*
+ if (bypass == 0)
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz
+ else
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz
+ */
+
+ return 1; // OK
+}
+#endif
+
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSI oscillator and activate PLL with HSI as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4)
+ RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> freq is ok but not precise enough
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 84 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+ return 1; // OK
+}
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xC/TARGET_DISCO_F401VC/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xC/TARGET_DISCO_F401VC/system_stm32f4xx.c
deleted file mode 100644
index 0a8a02ebdf..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xC/TARGET_DISCO_F401VC/system_stm32f4xx.c
+++ /dev/null
@@ -1,931 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 84 | 84
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 84 | 84
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 42 | 42
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 84 | 84
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (1) /* Use external clock */
-#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 84000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- /* Output clock on MCO2 pin(PC9) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_1); // 84 MHz
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSE oscillator and activate PLL with HSE as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
- }
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> OK for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 84 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 42 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 84 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- /*
- if (bypass == 0)
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz
- else
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz
- */
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSI oscillator and activate PLL with HSI as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> freq is ok but not precise enough
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 84 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 42 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 84 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xE/TARGET_NUCLEO_F401RE/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xE/TARGET_NUCLEO_F401RE/system_clock.c
new file mode 100644
index 0000000000..e0007d2dcd
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xE/TARGET_NUCLEO_F401RE/system_clock.c
@@ -0,0 +1,239 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- USE_PLL_HSE_EXTC (external 8 MHz clock)
+ * | 2- USE_PLL_HSE_XTAL (external 8 MHz xtal)
+ * | 3- USE_PLL_HSI (internal 16 MHz)
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 84
+ * AHBCLK (MHz) | 84
+ * APB1CLK (MHz) | 42
+ * APB2CLK (MHz) | 84
+ * USB capable | YES
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+#include "mbed_assert.h"
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+
+// clock source is selected with CLOCK_SOURCE in json config
+#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
+#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
+#define USE_PLL_HSI 0x2 // Use HSI internal clock
+
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+uint8_t SetSysClock_PLL_HSI(void);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+/*
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+
+void SetSysClock(void)
+{
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
+ /* 1- Try to start with HSE and external clock */
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
+ /* 2- If fail try to start with HSE and external xtal */
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0)
+#endif
+ {
+ while(1) {
+ MBED_ASSERT(1);
+ }
+ }
+ }
+ }
+
+ /* Output clock on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
+}
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ // Enable HSE oscillator and activate PLL with HSE as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
+ }
+
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4)
+ RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> OK for USB
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 84 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ /*
+ if (bypass == 0)
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz
+ else
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz
+ */
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ // Enable HSI oscillator and activate PLL with HSI as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4)
+ RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> freq is ok but not precise enough
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 84 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xE/TARGET_NUCLEO_F401RE/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xE/TARGET_NUCLEO_F401RE/system_stm32f4xx.c
deleted file mode 100644
index 0a8a02ebdf..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F401xE/TARGET_NUCLEO_F401RE/system_stm32f4xx.c
+++ /dev/null
@@ -1,931 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 84 | 84
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 84 | 84
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 42 | 42
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 84 | 84
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (1) /* Use external clock */
-#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 84000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- /* Output clock on MCO2 pin(PC9) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_1); // 84 MHz
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSE oscillator and activate PLL with HSE as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
- }
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> OK for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 84 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 42 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 84 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- /*
- if (bypass == 0)
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz
- else
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz
- */
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSI oscillator and activate PLL with HSI as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> freq is ok but not precise enough
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 84 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 42 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 84 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_ARCH_MAX/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_ARCH_MAX/system_clock.c
new file mode 100644
index 0000000000..ec7533adec
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_ARCH_MAX/system_clock.c
@@ -0,0 +1,232 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
+ * | (external 8 MHz clock) | (internal 16 MHz)
+ * | 2- PLL_HSE_XTAL |
+ * | (external 8 MHz xtal) |
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 168 | 168
+ *-----------------------------------------------------------------------------
+ * AHBCLK (MHz) | 168 | 168
+ *-----------------------------------------------------------------------------
+ * APB1CLK (MHz) | 42 | 42
+ *-----------------------------------------------------------------------------
+ * APB2CLK (MHz) | 84 | 84
+ *-----------------------------------------------------------------------------
+ * USB capable (48 MHz precise clock) | YES | NO
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
+#define USE_PLL_HSE_EXTC (1) /* Use external clock */
+#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
+
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif
+
+uint8_t SetSysClock_PLL_HSI(void);
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+void SetSysClock(void)
+{
+ /* 1- Try to start with HSE and external clock */
+#if USE_PLL_HSE_EXTC != 0
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+ /* 2- If fail try to start with HSE and external xtal */
+#if USE_PLL_HSE_XTAL != 0
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0) {
+ while(1) {
+ // [TODO] Put something here to tell the user that a problem occured...
+ }
+ }
+ }
+ }
+
+ /* Output clock on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_1); // 84 MHz
+}
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSE oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
+ }
+ RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> OK for USB
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 168 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz (SPI1 clock...)
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ /*
+ if (bypass == 0)
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz
+ else
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz
+ */
+
+ return 1; // OK
+}
+#endif
+
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSI oscillator and activate PLL with HSI as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> freq is ok but not precise enough
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 168 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+ return 1; // OK
+}
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_ARCH_MAX/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_ARCH_MAX/system_stm32f4xx.c
deleted file mode 100644
index 6b969400cd..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_ARCH_MAX/system_stm32f4xx.c
+++ /dev/null
@@ -1,1097 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 168 | 168
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 168 | 168
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 42 | 42
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 84 | 84
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (1) /* Use external clock */
-#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
- uint32_t SystemCoreClock = 168000000; /* [CHANGED FOR MBED] */
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
- defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- /* Output clock on MCO2 pin(PC9) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_1); // 84 MHz
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSE oscillator and activate PLL with HSE as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
- }
-RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> OK for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 168 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz (SPI1 clock...)
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- /*
- if (bypass == 0)
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz
- else
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz
- */
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSI oscillator and activate PLL with HSI as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> freq is ok but not precise enough
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 168 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_DISCO_F407VG/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_DISCO_F407VG/system_clock.c
new file mode 100644
index 0000000000..5610e67950
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_DISCO_F407VG/system_clock.c
@@ -0,0 +1,234 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
+ * | (external 8 MHz clock) | (internal 16 MHz)
+ * | 2- PLL_HSE_XTAL |
+ * | (external 8 MHz xtal) |
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 168 | 168
+ *-----------------------------------------------------------------------------
+ * AHBCLK (MHz) | 168 | 168
+ *-----------------------------------------------------------------------------
+ * APB1CLK (MHz) | 42 | 42
+ *-----------------------------------------------------------------------------
+ * APB2CLK (MHz) | 84 | 84
+ *-----------------------------------------------------------------------------
+ * USB capable (48 MHz precise clock) | YES | NO
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+
+/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
+#define USE_PLL_HSE_EXTC (1) /* Use external clock */
+#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
+
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif
+
+uint8_t SetSysClock_PLL_HSI(void);
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+void SetSysClock(void)
+{
+ /* 1- Try to start with HSE and external clock */
+#if USE_PLL_HSE_EXTC != 0
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+ /* 2- If fail try to start with HSE and external xtal */
+#if USE_PLL_HSE_XTAL != 0
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0) {
+ while(1) {
+ // [TODO] Put something here to tell the user that a problem occured...
+ }
+ }
+ }
+ }
+
+ /* Output clock on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_1); // 84 MHz
+}
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSE oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
+ }
+ RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> OK for USB
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 168 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz (SPI1 clock...)
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ /*
+ if (bypass == 0)
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz
+ else
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz
+ */
+
+ return 1; // OK
+}
+#endif
+
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSI oscillator and activate PLL with HSI as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> freq is ok but not precise enough
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 168 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+ return 1; // OK
+}
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_DISCO_F407VG/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_DISCO_F407VG/system_stm32f4xx.c
deleted file mode 100644
index 6b969400cd..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F407xG/TARGET_DISCO_F407VG/system_stm32f4xx.c
+++ /dev/null
@@ -1,1097 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 168 | 168
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 168 | 168
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 42 | 42
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 84 | 84
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (1) /* Use external clock */
-#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
- uint32_t SystemCoreClock = 168000000; /* [CHANGED FOR MBED] */
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
- defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- /* Output clock on MCO2 pin(PC9) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_1); // 84 MHz
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSE oscillator and activate PLL with HSE as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
- }
-RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> OK for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 168 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz (SPI1 clock...)
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- /*
- if (bypass == 0)
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz
- else
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz
- */
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSI oscillator and activate PLL with HSI as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> freq is ok but not precise enough
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 168 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F410xB/TARGET_NUCLEO_F410RB/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F410xB/TARGET_NUCLEO_F410RB/system_clock.c
new file mode 100644
index 0000000000..eea33699a1
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F410xB/TARGET_NUCLEO_F410RB/system_clock.c
@@ -0,0 +1,239 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- USE_PLL_HSE_EXTC (external 8 MHz clock)
+ * | 2- USE_PLL_HSE_XTAL (external 8 MHz xtal)
+ * | 3- USE_PLL_HSI (internal 16 MHz)
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 100
+ * AHBCLK (MHz) | 100
+ * APB1CLK (MHz) | 100
+ * APB2CLK (MHz) | 100
+ * USB capable | NO
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+#include "mbed_assert.h"
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+
+// clock source is selected with CLOCK_SOURCE in json config
+#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
+#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
+#define USE_PLL_HSI 0x2 // Use HSI internal clock
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+uint8_t SetSysClock_PLL_HSI(void);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/**
+* @brief Configures the System clock source, PLL Multiplier and Divider factors,
+* AHB/APBx prescalers and Flash settings
+* @note This function should be called only once the RCC clock configuration
+* is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+
+void SetSysClock(void)
+{
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
+ /* 1- Try to start with HSE and external clock */
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
+ /* 2- If fail try to start with HSE and external xtal */
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0)
+#endif
+ {
+ while(1) {
+ MBED_ASSERT(1);
+ }
+ }
+ }
+ }
+
+ /* Output clock on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
+}
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ // Enable HSE oscillator and activate PLL with HSE as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
+ }
+
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 4;
+ RCC_OscInitStruct.PLL.PLLN = 100;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 4;
+ RCC_OscInitStruct.PLL.PLLR = 2;
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //if (bypass == 0)
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
+ //else
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ // Enable HSI oscillator and activate PLL with HSI as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 8;
+ RCC_OscInitStruct.PLL.PLLN = 100;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 4;
+ RCC_OscInitStruct.PLL.PLLR = 2;
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F410xB/TARGET_NUCLEO_F410RB/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F410xB/TARGET_NUCLEO_F410RB/system_stm32f4xx.c
deleted file mode 100644
index a07d48f47c..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F410xB/TARGET_NUCLEO_F410RB/system_stm32f4xx.c
+++ /dev/null
@@ -1,915 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- *
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)25000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (1) /* Use external clock */
-#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 16000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- /* Output clock on MCO2 pin(PC9) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 100 MHz / 4 = 25 MHz
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSE oscillator and activate PLL with HSE as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
- }
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- //RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- //RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (1 MHz * 384)
- RCC_OscInitStruct.PLL.PLLM = 4; // VCO input clock = 2 MHz (8 MHz / 4)
- RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 96 MHz (384 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 48 MHz (384 MHz / 8) --> Good for USB
- RCC_OscInitStruct.PLL.PLLR = 2; // I2S clocks
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
-
- //if (bypass == 0)
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
- //else
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSI oscillator and activate PLL with HSI as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- //RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- //RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (1 MHz * 384)
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 2 MHz (16 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 96 MHz (384 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 48 MHz (384 MHz / 8) --> Good for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_ELMO_F411RE/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_ELMO_F411RE/system_clock.c
new file mode 100644
index 0000000000..4153c6c35d
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_ELMO_F411RE/system_clock.c
@@ -0,0 +1,243 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
+ * | (external 8 MHz clock) | (internal 16 MHz)
+ * | 2- PLL_HSE_XTAL |
+ * | (external 8 MHz xtal) |
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 96 | 96
+ *-----------------------------------------------------------------------------
+ * AHBCLK (MHz) | 96 | 96
+ *-----------------------------------------------------------------------------
+ * APB1CLK (MHz) | 48 | 48
+ *-----------------------------------------------------------------------------
+ * APB2CLK (MHz) | 96 | 96
+ *-----------------------------------------------------------------------------
+ * USB capable (48 MHz precise clock) | YES | YES
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+
+/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
+#define USE_PLL_HSE_EXTC (0) /* Use external clock */
+#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
+
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif
+
+uint8_t SetSysClock_PLL_HSI(void);
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/**
+* @brief Configures the System clock source, PLL Multiplier and Divider factors,
+* AHB/APBx prescalers and Flash settings
+* @note This function should be called only once the RCC clock configuration
+* is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+void SetSysClock(void)
+{
+ /* 1- Try to start with HSE and external clock */
+#if USE_PLL_HSE_EXTC != 0
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+ /* 2- If fail try to start with HSE and external xtal */
+#if USE_PLL_HSE_XTAL != 0
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0) {
+ while(1) {
+ // [TODO] Put something here to tell the user that a problem occured...
+ }
+ }
+ }
+ }
+
+ /* Output clock on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 100 MHz / 4 = 25 MHz
+}
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSE oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
+ }
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ //RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
+ //RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (1 MHz * 384)
+ //RCC_OscInitStruct.PLL.PLLM = 4; // VCO input clock = 2 MHz (8 MHz / 4)
+ //RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
+
+ RCC_OscInitStruct.PLL.PLLM = 25; // VCO input clock = 2 MHz (8 MHz / 4)
+ RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (2 MHz * 192)
+
+
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 96 MHz (384 MHz / 4)
+ RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 48 MHz (384 MHz / 8) --> Good for USB
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+
+ //if (bypass == 0)
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
+ //else
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
+
+ return 1; // OK
+}
+#endif
+
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSI oscillator and activate PLL with HSI as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ //RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ //RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (1 MHz * 384)
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 2 MHz (16 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 96 MHz (384 MHz / 4)
+ RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 48 MHz (384 MHz / 8) --> Good for USB
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+ return 1; // OK
+}
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_ELMO_F411RE/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_ELMO_F411RE/system_stm32f4xx.c
deleted file mode 100644
index 546d3719a1..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_ELMO_F411RE/system_stm32f4xx.c
+++ /dev/null
@@ -1,940 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 96 | 96
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 96 | 96
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 48 | 48
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 96 | 96
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | YES
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)25000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (0) /* Use external clock */
-#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 16000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- /* Output clock on MCO2 pin(PC9) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 100 MHz / 4 = 25 MHz
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSE oscillator and activate PLL with HSE as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
- }
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- //RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- //RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (1 MHz * 384)
- //RCC_OscInitStruct.PLL.PLLM = 4; // VCO input clock = 2 MHz (8 MHz / 4)
- //RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
-
- RCC_OscInitStruct.PLL.PLLM = 25; // VCO input clock = 2 MHz (8 MHz / 4)
- RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (2 MHz * 192)
-
-
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 96 MHz (384 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 48 MHz (384 MHz / 8) --> Good for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
-
- //if (bypass == 0)
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
- //else
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSI oscillator and activate PLL with HSI as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- //RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- //RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (1 MHz * 384)
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 2 MHz (16 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 96 MHz (384 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 48 MHz (384 MHz / 8) --> Good for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_NUCLEO_F411RE/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_NUCLEO_F411RE/system_clock.c
new file mode 100644
index 0000000000..cccd9762de
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_NUCLEO_F411RE/system_clock.c
@@ -0,0 +1,245 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- USE_PLL_HSE_EXTC (external 8 MHz clock) | CLOCK_SOURCE_USB=1
+ * | 2- USE_PLL_HSE_XTAL (external 8 MHz xtal) |
+ * | 3- USE_PLL_HSI (internal 16 MHz) |
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 100 | 96
+ * AHBCLK (MHz) | 100 | 96
+ * APB1CLK (MHz) | 50 | 48
+ * APB2CLK (MHz) | 100 | 96
+ * USB capable | NO | YES
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+#include "mbed_assert.h"
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+
+// clock source is selected with CLOCK_SOURCE in json config
+#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
+#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
+#define USE_PLL_HSI 0x2 // Use HSI internal clock
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+uint8_t SetSysClock_PLL_HSI(void);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/**
+* @brief Configures the System clock source, PLL Multiplier and Divider factors,
+* AHB/APBx prescalers and Flash settings
+* @note This function should be called only once the RCC clock configuration
+* is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+
+void SetSysClock(void)
+{
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
+ /* 1- Try to start with HSE and external clock */
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
+ /* 2- If fail try to start with HSE and external xtal */
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0)
+#endif
+ {
+ while(1) {
+ MBED_ASSERT(1);
+ }
+ }
+ }
+ }
+
+ /* Output clock on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
+}
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ // Enable HSE oscillator and activate PLL with HSE as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
+ }
+
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 4; // VCO input clock = 2 MHz (8 MHz / 4)
+#if (CLOCK_SOURCE_USB)
+ RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
+#else /* CLOCK_SOURCE_USB */
+ RCC_OscInitStruct.PLL.PLLN = 200; // VCO output clock = 400 MHz (2 MHz * 200)
+#endif /* CLOCK_SOURCE_USB */
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 100 MHz or 96 MHz (depending on CLOCK_SOURCE_USB)
+ RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 48 MHz (CLOCK_SOURCE_USB=1)
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 100/96 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 100/96 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 50/48 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 100/96 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //if (bypass == 0)
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
+ //else
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ // Enable HSI oscillator and activate PLL with HSI as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 2 MHz (16 MHz / 8)
+#if (CLOCK_SOURCE_USB)
+ RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
+#else /* CLOCK_SOURCE_USB */
+ RCC_OscInitStruct.PLL.PLLN = 200; // VCO output clock = 400 MHz (2 MHz * 200)
+#endif /* CLOCK_SOURCE_USB */
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 100 MHz or 96 MHz (depending on CLOCK_SOURCE_USB)
+ RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 48 MHz (CLOCK_SOURCE_USB=1)
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_NUCLEO_F411RE/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_NUCLEO_F411RE/system_stm32f4xx.c
deleted file mode 100644
index fd8d3057e7..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F411xE/TARGET_NUCLEO_F411RE/system_stm32f4xx.c
+++ /dev/null
@@ -1,935 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 96 | 96
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 96 | 96
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 48 | 48
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 96 | 96
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | YES
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (1) /* Use external clock */
-#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 16000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- /* Output clock on MCO2 pin(PC9) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 100 MHz / 4 = 25 MHz
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSE oscillator and activate PLL with HSE as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
- }
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- //RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- //RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (1 MHz * 384)
- RCC_OscInitStruct.PLL.PLLM = 4; // VCO input clock = 2 MHz (8 MHz / 4)
- RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 96 MHz (384 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 48 MHz (384 MHz / 8) --> Good for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
-
- //if (bypass == 0)
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
- //else
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- /* Enable HSI oscillator and activate PLL with HSI as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- //RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- //RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (1 MHz * 384)
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 2 MHz (16 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 96 MHz (384 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 8; // USB clock = 48 MHz (384 MHz / 8) --> Good for USB
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 96 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 96 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 48 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 96 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F412xG/TARGET_NUCLEO_F412ZG/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F412xG/TARGET_NUCLEO_F412ZG/system_clock.c
new file mode 100644
index 0000000000..5c546c53b4
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F412xG/TARGET_NUCLEO_F412ZG/system_clock.c
@@ -0,0 +1,267 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- USE_PLL_HSE_EXTC (external 8 MHz clock)
+ * | 2- USE_PLL_HSE_XTAL (external 8 MHz xtal)
+ * | 3- USE_PLL_HSI (internal 16 MHz)
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 100
+ * AHBCLK (MHz) | 100
+ * APB1CLK (MHz) | 50
+ * APB2CLK (MHz) | 100
+ * USB capable | YES
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+#include "mbed_assert.h"
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+
+// clock source is selected with CLOCK_SOURCE in json config
+#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
+#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
+#define USE_PLL_HSI 0x2 // Use HSI internal clock
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+uint8_t SetSysClock_PLL_HSI(void);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+
+void SetSysClock(void)
+{
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
+ /* 1- Try to start with HSE and external clock */
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
+ /* 2- If fail try to start with HSE and external xtal */
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0)
+#endif
+ {
+ while(1) {
+ MBED_ASSERT(1);
+ }
+ }
+ }
+ }
+
+ /* Output clock on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
+}
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSE oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
+ }
+
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 200; // VCO output clock = 200 MHz (1 MHz * 200)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 100 MHz (200 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7;
+ RCC_OscInitStruct.PLL.PLLR = 2;
+
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLLSAI output as USB clock source */
+ PeriphClkInitStruct.PLLI2S.PLLI2SM = 8;
+ PeriphClkInitStruct.PLLI2S.PLLI2SQ = 4;
+ PeriphClkInitStruct.PLLI2S.PLLI2SN = 192;
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+ PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLI2SQ;
+
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //if (bypass == 0)
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
+ //else
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSI oscillator and activate PLL with HSI as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 2 MHz (16 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 100; // VCO output clock = 200 MHz (2 MHz * 100)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 100 MHz (200 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 2;
+ RCC_OscInitStruct.PLL.PLLR = 2;
+
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLLSAI output as USB clock source */
+ PeriphClkInitStruct.PLLI2S.PLLI2SM = 16;
+ PeriphClkInitStruct.PLLI2S.PLLI2SN = 192;
+ PeriphClkInitStruct.PLLI2S.PLLI2SQ = 4;
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+ PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLI2SQ;
+
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F412xG/TARGET_NUCLEO_F412ZG/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F412xG/TARGET_NUCLEO_F412ZG/system_stm32f4xx.c
deleted file mode 100644
index a88813d43f..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F412xG/TARGET_NUCLEO_F412ZG/system_stm32f4xx.c
+++ /dev/null
@@ -1,963 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 100 | 96
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 100 | 96
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 50 | 48
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 100 | 96
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | YES
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (1) /* Use external clock */
-#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 16000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- /* Output clock on MCO2 pin(PC9) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
-
- /* Enable Power Control clock */
- __HAL_RCC_PWR_CLK_ENABLE();
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- /* Enable HSE oscillator and activate PLL with HSE as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
- }
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
-
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 200; // VCO output clock = 200 MHz (1 MHz * 200)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 100 MHz (200 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7;
- RCC_OscInitStruct.PLL.PLLR = 2;
-
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLLSAI output as USB clock source */
- PeriphClkInitStruct.PLLI2S.PLLI2SM = 8;
- PeriphClkInitStruct.PLLI2S.PLLI2SQ = 4;
- PeriphClkInitStruct.PLLI2S.PLLI2SN = 192;
- PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
- PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLI2SQ;
-
- HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
-
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //if (bypass == 0)
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
- //else
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
-
- /* Enable Power Control clock */
- __HAL_RCC_PWR_CLK_ENABLE();
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- /* Enable HSI oscillator and activate PLL with HSI as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
-
- //RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- //RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (1 MHz * 384)
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 2 MHz (16 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 96 MHz (384 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 8;
- RCC_OscInitStruct.PLL.PLLQ = 2;
-
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLLSAI output as USB clock source */
- PeriphClkInitStruct.PLLI2S.PLLI2SM = 8;
- PeriphClkInitStruct.PLLI2S.PLLI2SQ = 4;
- PeriphClkInitStruct.PLLI2S.PLLI2SN = 192;
- PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
- PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLI2SQ;
-
- HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F413xH/TARGET_DISCO_F413ZH/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F413xH/TARGET_DISCO_F413ZH/system_clock.c
new file mode 100644
index 0000000000..34aa173313
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F413xH/TARGET_DISCO_F413ZH/system_clock.c
@@ -0,0 +1,269 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- USE_PLL_HSE_EXTC (external 8 MHz clock)
+ * | 2- USE_PLL_HSE_XTAL (external 8 MHz xtal)
+ * | 3- USE_PLL_HSI (internal 16 MHz)
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 100
+ * AHBCLK (MHz) | 100
+ * APB1CLK (MHz) | 50
+ * APB2CLK (MHz) | 100
+ * USB capable | YES
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+#include "mbed_assert.h"
+
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+
+// clock source is selected with CLOCK_SOURCE in json config
+#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
+#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
+#define USE_PLL_HSI 0x2 // Use HSI internal clock
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+uint8_t SetSysClock_PLL_HSI(void);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+
+void SetSysClock(void)
+{
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
+ /* 1- Try to start with HSE and external clock */
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
+ /* 2- If fail try to start with HSE and external xtal */
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0)
+#endif
+ {
+ while(1) {
+ MBED_ASSERT(1);
+ }
+ }
+ }
+ }
+
+ /* Output clock on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
+}
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSE oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
+ }
+
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 200; // VCO output clock = 200 MHz (1 MHz * 200)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 100 MHz (200 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7;
+ RCC_OscInitStruct.PLL.PLLR = 2;
+
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLLSAI output as USB clock source */
+ PeriphClkInitStruct.PLLI2S.PLLI2SM = 8;
+ PeriphClkInitStruct.PLLI2S.PLLI2SQ = 4;
+ PeriphClkInitStruct.PLLI2S.PLLI2SN = 192;
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+ PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLI2SQ;
+
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //if (bypass == 0)
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
+ //else
+ // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSI oscillator and activate PLL with HSI as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 2 MHz (16 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 100; // VCO output clock = 200 MHz (2 MHz * 100)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 100 MHz (200 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 2;
+ RCC_OscInitStruct.PLL.PLLR = 2;
+
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLLI2S output as USB clock source */
+ PeriphClkInitStruct.PLLI2S.PLLI2SM = 16;
+ PeriphClkInitStruct.PLLI2S.PLLI2SN = 192;
+ PeriphClkInitStruct.PLLI2S.PLLI2SQ = 4;
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+ PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLI2SQ;
+
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Output clock on MCO1 pin(PA8) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F413xH/TARGET_DISCO_F413ZH/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F413xH/TARGET_DISCO_F413ZH/system_stm32f4xx.c
deleted file mode 100644
index 1a10619f29..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F413xH/TARGET_DISCO_F413ZH/system_stm32f4xx.c
+++ /dev/null
@@ -1,975 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 100 | 96
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 100 | 96
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 50 | 48
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 100 | 96
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | YES
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-#include "hal_tick.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (1) /* Use external clock */
-#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 16000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
- /* Configure the Cube driver */
- SystemCoreClock = 16000000; // At this stage the HSI is used as system clock
- HAL_Init();
-
- /* Configure the System clock source, PLL Multiplier and Divider factors,
- AHB/APBx prescalers and Flash settings */
- SetSysClock();
-
- /* Reset the timer to avoid issues after the RAM initialization */
- TIM_MST_RESET_ON;
- TIM_MST_RESET_OFF;
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- /* Output clock on MCO2 pin(PC9) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
-
- /* Enable Power Control clock */
- __HAL_RCC_PWR_CLK_ENABLE();
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- /* Enable HSE oscillator and activate PLL with HSE as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
- }
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
-
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 200; // VCO output clock = 200 MHz (1 MHz * 200)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 100 MHz (200 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7;
- RCC_OscInitStruct.PLL.PLLR = 2;
-
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLLSAI output as USB clock source */
- PeriphClkInitStruct.PLLI2S.PLLI2SM = 8;
- PeriphClkInitStruct.PLLI2S.PLLI2SQ = 4;
- PeriphClkInitStruct.PLLI2S.PLLI2SN = 192;
- PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CK48;
- PeriphClkInitStruct.Clk48ClockSelection = RCC_CK48CLKSOURCE_PLLI2SQ;
-
- HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
-
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //if (bypass == 0)
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
- //else
- // HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
-
- /* Enable Power Control clock */
- __HAL_RCC_PWR_CLK_ENABLE();
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- /* Enable HSI oscillator and activate PLL with HSI as source */
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
-
- //RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- //RCC_OscInitStruct.PLL.PLLN = 384; // VCO output clock = 384 MHz (1 MHz * 384)
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 2 MHz (16 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 192; // VCO output clock = 384 MHz (2 MHz * 192)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 96 MHz (384 MHz / 4)
- RCC_OscInitStruct.PLL.PLLQ = 8;
- RCC_OscInitStruct.PLL.PLLQ = 2;
-
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLLSAI output as USB clock source */
- PeriphClkInitStruct.PLLI2S.PLLI2SM = 8;
- PeriphClkInitStruct.PLLI2S.PLLI2SQ = 4;
- PeriphClkInitStruct.PLLI2S.PLLI2SN = 192;
- PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CK48;
- PeriphClkInitStruct.Clk48ClockSelection = RCC_CK48CLKSOURCE_PLLI2SQ;
-
- HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Output clock on MCO1 pin(PA8) for debugging purpose */
- //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_DISCO_F429ZI/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_DISCO_F429ZI/system_clock.c
new file mode 100644
index 0000000000..b828467d91
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_DISCO_F429ZI/system_clock.c
@@ -0,0 +1,229 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------------
+ * System clock source | 1- USE_PLL_HSE_EXTC (external 8 MHz clock) |
+ * | 2- USE_PLL_HSE_XTAL (external 8 MHz xtal) | CLOCK_SOURCE_USB=1
+ * | 3- USE_PLL_HSI (internal 16 MHz clock) |
+ *-----------------------------------------------------------------------------------
+ * SYSCLK(MHz) | 180 | 168
+ * AHBCLK (MHz) | 180 | 168
+ * APB1CLK (MHz) | 45 | 42
+ * APB2CLK (MHz) | 90 | 84
+ * USB capable (48 MHz) | NO | YES (HSI calibration needed)
+ *-----------------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+
+#include "mbed_assert.h"
+
+// clock source is selected with CLOCK_SOURCE in json config
+#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
+#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
+#define USE_PLL_HSI 0x2 // Use HSI internal clock
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+uint8_t SetSysClock_PLL_HSI(void);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+}
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+
+void SetSysClock(void)
+{
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
+ /* 1- Try to start with HSE and external clock */
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
+ /* 2- If fail try to start with HSE and external xtal */
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0)
+#endif
+ {
+ while(1) {
+ MBED_ASSERT(1);
+ }
+ }
+ }
+ }
+}
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ // Enable HSE oscillator and activate PLL with HSE as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
+ }
+
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8;
+#if (CLOCK_SOURCE_USB)
+ RCC_OscInitStruct.PLL.PLLN = 336;
+#else
+ RCC_OscInitStruct.PLL.PLLN = 360;
+#endif
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // 180 MHz or 168 MHz if CLOCK_SOURCE_USB defined
+ RCC_OscInitStruct.PLL.PLLQ = 7; // 48 MHz if CLOCK_SOURCE_USB defined
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Activate the OverDrive to reach the 180 MHz Frequency
+ if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 or 168 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 or 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 or 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+ return 1;
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ // Enable HSI oscillator and activate PLL with HSI as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 8;
+#if (CLOCK_SOURCE_USB)
+ RCC_OscInitStruct.PLL.PLLN = 168;
+#else
+ RCC_OscInitStruct.PLL.PLLN = 180;
+#endif
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // 180 MHz or 168 MHz if CLOCK_SOURCE_USB defined
+ RCC_OscInitStruct.PLL.PLLQ = 7; // 48 MHz if CLOCK_SOURCE_USB defined
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Activate the OverDrive to reach the 180 MHz Frequency
+ if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 or 168 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 or 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 or 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+ return 1;
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_DISCO_F429ZI/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_DISCO_F429ZI/system_stm32f4xx.c
deleted file mode 100644
index fcb4942165..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_DISCO_F429ZI/system_stm32f4xx.c
+++ /dev/null
@@ -1,853 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *--------------------------------------------------------------------------------------
- * System clock source | PLL_HSE_XTAL | PLL_HSE_XTAL
- * | (external 8 MHz clock) | (external 8 MHz clock)
- *--------------------------------------------------------------------------------------
- * SYSCLK(MHz) | 168 | 180
- *--------------------------------------------------------------------------------------
- * AHBCLK (MHz) | 168 | 180
- *--------------------------------------------------------------------------------------
- * APB1CLK (MHz) | 42 | 45
- *--------------------------------------------------------------------------------------
- * APB2CLK (MHz) | 84 | 90
- *--------------------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *--------------------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the SYSCLOCK to start with (0=OFF, 1=ON) */
-#define USE_SYSCLOCK_168 (1) /* Use external 8MHz xtal and sets SYSCLK to 168MHz */
-#define USE_SYSCLOCK_180 (0) /* Use external 8MHz xtal and sets SYSCLK to 180MHz */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
- uint32_t SystemCoreClock = 168000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-void SetSysClock(void);
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/** System Clock Configuration
-*/
-#if USE_SYSCLOCK_168 != 0
-/*
- * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
- * and SYSCLK=168MHZ
- */
-void SetSysClock(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8;
- RCC_OscInitStruct.PLL.PLLN = 336;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
-
- // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
-
-
-}
-
-#elif USE_SYSCLOCK_180 != 0
-/*
- * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
- * and SYSCLK=180MHZ
- */
-void SetSysClock(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8;
- RCC_OscInitStruct.PLL.PLLN = 360;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- HAL_PWREx_EnableOverDrive();
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
-
- // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
-
-}
-#endif
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_NUCLEO_F429ZI/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_NUCLEO_F429ZI/system_clock.c
new file mode 100644
index 0000000000..b828467d91
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_NUCLEO_F429ZI/system_clock.c
@@ -0,0 +1,229 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------------
+ * System clock source | 1- USE_PLL_HSE_EXTC (external 8 MHz clock) |
+ * | 2- USE_PLL_HSE_XTAL (external 8 MHz xtal) | CLOCK_SOURCE_USB=1
+ * | 3- USE_PLL_HSI (internal 16 MHz clock) |
+ *-----------------------------------------------------------------------------------
+ * SYSCLK(MHz) | 180 | 168
+ * AHBCLK (MHz) | 180 | 168
+ * APB1CLK (MHz) | 45 | 42
+ * APB2CLK (MHz) | 90 | 84
+ * USB capable (48 MHz) | NO | YES (HSI calibration needed)
+ *-----------------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+
+#include "mbed_assert.h"
+
+// clock source is selected with CLOCK_SOURCE in json config
+#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
+#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
+#define USE_PLL_HSI 0x2 // Use HSI internal clock
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+uint8_t SetSysClock_PLL_HSI(void);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+}
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+
+void SetSysClock(void)
+{
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
+ /* 1- Try to start with HSE and external clock */
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
+ /* 2- If fail try to start with HSE and external xtal */
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0)
+#endif
+ {
+ while(1) {
+ MBED_ASSERT(1);
+ }
+ }
+ }
+ }
+}
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ // Enable HSE oscillator and activate PLL with HSE as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
+ }
+
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8;
+#if (CLOCK_SOURCE_USB)
+ RCC_OscInitStruct.PLL.PLLN = 336;
+#else
+ RCC_OscInitStruct.PLL.PLLN = 360;
+#endif
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // 180 MHz or 168 MHz if CLOCK_SOURCE_USB defined
+ RCC_OscInitStruct.PLL.PLLQ = 7; // 48 MHz if CLOCK_SOURCE_USB defined
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Activate the OverDrive to reach the 180 MHz Frequency
+ if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 or 168 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 or 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 or 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+ return 1;
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ // Enable HSI oscillator and activate PLL with HSI as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 8;
+#if (CLOCK_SOURCE_USB)
+ RCC_OscInitStruct.PLL.PLLN = 168;
+#else
+ RCC_OscInitStruct.PLL.PLLN = 180;
+#endif
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // 180 MHz or 168 MHz if CLOCK_SOURCE_USB defined
+ RCC_OscInitStruct.PLL.PLLQ = 7; // 48 MHz if CLOCK_SOURCE_USB defined
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Activate the OverDrive to reach the 180 MHz Frequency
+ if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 or 168 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 or 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 or 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+ return 1;
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_NUCLEO_F429ZI/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_NUCLEO_F429ZI/system_stm32f4xx.c
deleted file mode 100644
index 96e9ac0f50..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/TARGET_NUCLEO_F429ZI/system_stm32f4xx.c
+++ /dev/null
@@ -1,854 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *--------------------------------------------------------------------------------------
- * System clock source | PLL_HSE_XTAL | PLL_HSE_XTAL
- * | (external 8 MHz clock) | (external 8 MHz clock)
- *--------------------------------------------------------------------------------------
- * SYSCLK(MHz) | 168 | 180
- *--------------------------------------------------------------------------------------
- * AHBCLK (MHz) | 168 | 180
- *--------------------------------------------------------------------------------------
- * APB1CLK (MHz) | 42 | 45
- *--------------------------------------------------------------------------------------
- * APB2CLK (MHz) | 84 | 90
- *--------------------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *--------------------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-#include "nvic_addr.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the SYSCLOCK to start with (0=OFF, 1=ON) */
-#define USE_SYSCLOCK_168 (1) /* Use external 8MHz xtal and sets SYSCLK to 168MHz */
-#define USE_SYSCLOCK_180 (0) /* Use external 8MHz xtal and sets SYSCLK to 180MHz */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
- uint32_t SystemCoreClock = 168000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-void SetSysClock(void);
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/** System Clock Configuration
-*/
-#if USE_SYSCLOCK_168 != 0
-/*
- * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
- * and SYSCLK=168MHZ
- */
-void SetSysClock(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8;
- RCC_OscInitStruct.PLL.PLLN = 336;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
-
- // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
-
-
-}
-
-#elif USE_SYSCLOCK_180 != 0
-/*
- * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
- * and SYSCLK=180MHZ
- */
-void SetSysClock(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8;
- RCC_OscInitStruct.PLL.PLLN = 360;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- HAL_PWREx_EnableOverDrive();
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
-
- // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
-
-}
-#endif
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F437xG/TARGET_UBLOX_C030/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F437xG/TARGET_UBLOX_C030/system_clock.c
new file mode 100644
index 0000000000..94c06fb8e9
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F437xG/TARGET_UBLOX_C030/system_clock.c
@@ -0,0 +1,183 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *----------------------------------------------------------------------------------------------------------------------------------------
+ * System clock source | PLL_HSE_XTAL | PLL_HSE_XTAL | PLL_HSE_XTAL | PLL_HSE_XTAL
+ * | (external 8 MHz clock) | (external 8 MHz clock) | (external 12 MHz clock)| (external 12 MHz clock)
+ *----------------------------------------------------------------------------------------------------------------------------------------
+ * SYSCLK(MHz) | 168 | 84 | 168 | 84
+ *----------------------------------------------------------------------------------------------------------------------------------------
+ * AHBCLK (MHz) | 168 | 84 | 168 | 84
+ *----------------------------------------------------------------------------------------------------------------------------------------
+ * APB1CLK (MHz) | 42 | 42 | 42 | 42
+ *----------------------------------------------------------------------------------------------------------------------------------------
+ * APB2CLK (MHz) | 84 | 84 | 84 | 84
+ *----------------------------------------------------------------------------------------------------------------------------------------
+ * USB capable (48 MHz precise clock) | YES | YES | YES | YES
+ *----------------------------------------------------------------------------------------------------------------------------------------
+**/
+
+#include "ublox_low_level_api.h"
+#include "stm32f4xx.h"
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+
+/* Select the SYSCLOCK to start with (0=OFF, 1=ON) */
+#define USE_SYSCLOCK_168 (1) /* Use external 8MHz or 12 MHz xtal and sets SYSCLK to 168MHz */
+#define USE_SYSCLOCK_84 (0) /* Use external 8MHz or 12 MHz xtal and sets SYSCLK to 84MHz */
+
+
+void SetSysClock(void);
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+ ublox_board_init();
+}
+
+
+
+/** System Clock Configuration
+*/
+#if USE_SYSCLOCK_168 != 0
+/*
+ * Set SYSCLK=168MHZ
+ */
+void SetSysClock(void)
+{
+
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+#ifdef USE_DEBUG_8MHz_XTAL
+ RCC_OscInitStruct.PLL.PLLM = 8;
+#else
+ RCC_OscInitStruct.PLL.PLLM = 12;
+#endif
+ RCC_OscInitStruct.PLL.PLLN = 336;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 7;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
+ |RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
+
+ // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+
+}
+
+#elif USE_SYSCLOCK_84 != 0
+/*
+Set SYSCLK=84MHZ
+ */
+void SetSysClock(void)
+{
+
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE3);
+
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+#ifdef USE_DEBUG_8MHz_XTAL
+ RCC_OscInitStruct.PLL.PLLM = 8;
+#else
+ RCC_OscInitStruct.PLL.PLLM = 12;
+#endif
+ RCC_OscInitStruct.PLL.PLLN = 336;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4;
+ RCC_OscInitStruct.PLL.PLLQ = 7;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
+ |RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);
+
+ // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+}
+#endif
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F437xG/TARGET_UBLOX_C030/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F437xG/TARGET_UBLOX_C030/system_stm32f4xx.c
deleted file mode 100644
index b062f171b2..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F437xG/TARGET_UBLOX_C030/system_stm32f4xx.c
+++ /dev/null
@@ -1,869 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *----------------------------------------------------------------------------------------------------------------------------------------
- * System clock source | PLL_HSE_XTAL | PLL_HSE_XTAL | PLL_HSE_XTAL | PLL_HSE_XTAL
- * | (external 8 MHz clock) | (external 8 MHz clock) | (external 12 MHz clock)| (external 12 MHz clock)
- *----------------------------------------------------------------------------------------------------------------------------------------
- * SYSCLK(MHz) | 168 | 84 | 168 | 84
- *----------------------------------------------------------------------------------------------------------------------------------------
- * AHBCLK (MHz) | 168 | 84 | 168 | 84
- *----------------------------------------------------------------------------------------------------------------------------------------
- * APB1CLK (MHz) | 42 | 42 | 42 | 42
- *----------------------------------------------------------------------------------------------------------------------------------------
- * APB2CLK (MHz) | 84 | 84 | 84 | 84
- *----------------------------------------------------------------------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | YES | YES | YES
- *----------------------------------------------------------------------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "ublox_low_level_api.h"
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the SYSCLOCK to start with (0=OFF, 1=ON) */
-#define USE_SYSCLOCK_168 (1) /* Use external 8MHz or 12 MHz xtal and sets SYSCLK to 168MHz */
-#define USE_SYSCLOCK_84 (0) /* Use external 8MHz or 12 MHz xtal and sets SYSCLK to 84MHz */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
- uint32_t SystemCoreClock = 168000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-void SetSysClock(void);
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
- ublox_board_init();
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/** System Clock Configuration
-*/
-#if USE_SYSCLOCK_168 != 0
-/*
- * Set SYSCLK=168MHZ
- */
-void SetSysClock(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
-#ifdef USE_DEBUG_8MHz_XTAL
- RCC_OscInitStruct.PLL.PLLM = 8;
-#else
- RCC_OscInitStruct.PLL.PLLM = 12;
-#endif
- RCC_OscInitStruct.PLL.PLLN = 336;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
-
- // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
-
-
-}
-
-#elif USE_SYSCLOCK_84 != 0
-/*
-Set SYSCLK=84MHZ
- */
-void SetSysClock(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE3);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
-#ifdef USE_DEBUG_8MHz_XTAL
- RCC_OscInitStruct.PLL.PLLM = 8;
-#else
- RCC_OscInitStruct.PLL.PLLM = 12;
-#endif
- RCC_OscInitStruct.PLL.PLLN = 336;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);
-
- // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
-
-}
-#endif
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_NUCLEO_F439ZI/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_NUCLEO_F439ZI/system_clock.c
new file mode 100644
index 0000000000..d135dd527a
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_NUCLEO_F439ZI/system_clock.c
@@ -0,0 +1,244 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------------
+ * System clock source | 1- USE_PLL_HSE_EXTC (CLOCK_SOURCE_USB=1) | 3- USE_PLL_HSI (CLOCK_SOURCE_USB=1)
+ * | (external 8 MHz clock) | (internal 16 MHz clock)
+ * | 2- USE_PLL_HSE_XTAL |
+ * | (external 8 MHz xtal) |
+ *-----------------------------------------------------------------------------------
+ * SYSCLK(MHz) | 180 (168)
+ *-----------------------------------------------------------------------------------
+ * AHBCLK (MHz) | 180 (168)
+ *-----------------------------------------------------------------------------------
+ * APB1CLK (MHz) | 45 (42)
+ *-----------------------------------------------------------------------------------
+ * APB2CLK (MHz) | 90 (84)
+ *-----------------------------------------------------------------------------------
+ * USB capable (48 MHz) | YES (HSI calibration needed)
+ *-----------------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+#include "nvic_addr.h"
+#include "mbed_assert.h"
+
+// clock source is selected with CLOCK_SOURCE in json config
+#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
+#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
+#define USE_PLL_HSI 0x2 // Use HSI internal clock
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+uint8_t SetSysClock_PLL_HSI(void);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = NVIC_FLASH_VECTOR_ADDRESS; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+
+void SetSysClock(void)
+{
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
+ /* 1- Try to start with HSE and external clock */
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
+ /* 2- If fail try to start with HSE and external xtal */
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0)
+#endif
+ {
+ while(1) {
+ MBED_ASSERT(1);
+ }
+ }
+ }
+ }
+}
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ // Enable HSE oscillator and activate PLL with HSE as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
+ }
+
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8;
+#if (CLOCK_SOURCE_USB)
+ RCC_OscInitStruct.PLL.PLLN = 336;
+#else
+ RCC_OscInitStruct.PLL.PLLN = 360;
+#endif
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // 180 MHz or 168 MHz if CLOCK_SOURCE_USB defined
+ RCC_OscInitStruct.PLL.PLLQ = 7; // 48 MHz if CLOCK_SOURCE_USB defined
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Activate the OverDrive to reach the 180 MHz Frequency
+ if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 or 168 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 or 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 or 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+ return 1;
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ // Enable HSI oscillator and activate PLL with HSI as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 8;
+#if (CLOCK_SOURCE_USB)
+ RCC_OscInitStruct.PLL.PLLN = 168;
+#else
+ RCC_OscInitStruct.PLL.PLLN = 180;
+#endif
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // 180 MHz or 168 MHz if CLOCK_SOURCE_USB defined
+ RCC_OscInitStruct.PLL.PLLQ = 7; // 48 MHz if CLOCK_SOURCE_USB defined
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Activate the OverDrive to reach the 180 MHz Frequency
+ if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 or 168 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 or 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 or 84 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+ return 1;
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_NUCLEO_F439ZI/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_NUCLEO_F439ZI/system_stm32f4xx.c
deleted file mode 100644
index 414f6b080b..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_NUCLEO_F439ZI/system_stm32f4xx.c
+++ /dev/null
@@ -1,865 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *--------------------------------------------------------------------------------------
- * System clock source | PLL_HSE_XTAL | PLL_HSE_XTAL
- * | (external 8 MHz clock) | (external 8 MHz clock)
- *--------------------------------------------------------------------------------------
- * SYSCLK(MHz) | 168 | 180
- *--------------------------------------------------------------------------------------
- * AHBCLK (MHz) | 168 | 180
- *--------------------------------------------------------------------------------------
- * APB1CLK (MHz) | 42 | 45
- *--------------------------------------------------------------------------------------
- * APB2CLK (MHz) | 84 | 90
- *--------------------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *--------------------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-#include "nvic_addr.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the SYSCLOCK to start with (0=OFF, 1=ON) */
-#define USE_SYSCLOCK_168 (1) /* Use external 8MHz xtal and sets SYSCLK to 168MHz */
-#define USE_SYSCLOCK_180 (0) /* Use external 8MHz xtal and sets SYSCLK to 180MHz */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
- uint32_t SystemCoreClock = 168000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-void SetSysClock(void);
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = NVIC_FLASH_VECTOR_ADDRESS; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/** System Clock Configuration
-*/
-#if USE_SYSCLOCK_168 != 0
-/*
- * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
- * and SYSCLK=168MHZ
- */
-void SetSysClock(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8;
- RCC_OscInitStruct.PLL.PLLN = 336;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
-
- // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
-
-
-}
-
-#elif USE_SYSCLOCK_180 != 0
-/*
- * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
- * and SYSCLK=180MHZ
- */
-void SetSysClock(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8;
- RCC_OscInitStruct.PLL.PLLN = 360;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- HAL_PWREx_EnableOverDrive();
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
-
- // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
-
-}
-#endif
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_UBLOX_EVK_ODIN_W2/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_UBLOX_EVK_ODIN_W2/system_clock.c
new file mode 100644
index 0000000000..fd95ee825b
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_UBLOX_EVK_ODIN_W2/system_clock.c
@@ -0,0 +1,170 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *--------------------------------------------------------------------------------------
+ * System clock source | PLL_HSE_XTAL | PLL_HSE_XTAL
+ * | (external 8 MHz clock) | (external 8 MHz clock)
+ *--------------------------------------------------------------------------------------
+ * SYSCLK(MHz) | 168 | 180
+ *--------------------------------------------------------------------------------------
+ * AHBCLK (MHz) | 168 | 180
+ *--------------------------------------------------------------------------------------
+ * APB1CLK (MHz) | 42 | 45
+ *--------------------------------------------------------------------------------------
+ * APB2CLK (MHz) | 84 | 90
+ *--------------------------------------------------------------------------------------
+ * USB capable (48 MHz precise clock) | YES | NO
+ *--------------------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+#include "nvic_addr.h"
+
+
+/* Select the SYSCLOCK to start with (0=OFF, 1=ON) */
+#define USE_SYSCLOCK_168 (1) /* Use external 8MHz xtal and sets SYSCLK to 168MHz */
+#define USE_SYSCLOCK_180 (0) /* Use external 8MHz xtal and sets SYSCLK to 180MHz */
+
+
+void SetSysClock(void);
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = NVIC_FLASH_VECTOR_ADDRESS; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/** System Clock Configuration
+*/
+#if USE_SYSCLOCK_168 != 0
+/*
+ * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
+ * and SYSCLK=168MHZ
+ */
+void SetSysClock(void)
+{
+
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 24;
+ RCC_OscInitStruct.PLL.PLLN = 336;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 7;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
+ |RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
+
+ // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+
+}
+
+#elif USE_SYSCLOCK_180 != 0
+/*
+ * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
+ * and SYSCLK=180MHZ
+ */
+void SetSysClock(void)
+{
+
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8;
+ RCC_OscInitStruct.PLL.PLLN = 360;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 7;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ HAL_PWREx_EnableOverDrive();
+
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
+ |RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
+
+ // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+}
+#endif
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_UBLOX_EVK_ODIN_W2/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_UBLOX_EVK_ODIN_W2/system_stm32f4xx.c
deleted file mode 100644
index 16d12f655b..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/TARGET_UBLOX_EVK_ODIN_W2/system_stm32f4xx.c
+++ /dev/null
@@ -1,865 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.5.0
- * @date 22-April-2016
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *--------------------------------------------------------------------------------------
- * System clock source | PLL_HSE_XTAL | PLL_HSE_XTAL
- * | (external 8 MHz clock) | (external 8 MHz clock)
- *--------------------------------------------------------------------------------------
- * SYSCLK(MHz) | 168 | 180
- *--------------------------------------------------------------------------------------
- * AHBCLK (MHz) | 168 | 180
- *--------------------------------------------------------------------------------------
- * APB1CLK (MHz) | 42 | 45
- *--------------------------------------------------------------------------------------
- * APB2CLK (MHz) | 84 | 90
- *--------------------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *--------------------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2016 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-#include "nvic_addr.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the SYSCLOCK to start with (0=OFF, 1=ON) */
-#define USE_SYSCLOCK_168 (1) /* Use external 8MHz xtal and sets SYSCLK to 168MHz */
-#define USE_SYSCLOCK_180 (0) /* Use external 8MHz xtal and sets SYSCLK to 180MHz */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
- uint32_t SystemCoreClock = 168000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-void SetSysClock(void);
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = NVIC_FLASH_VECTOR_ADDRESS; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
- defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/** System Clock Configuration
-*/
-#if USE_SYSCLOCK_168 != 0
-/*
- * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
- * and SYSCLK=168MHZ
- */
-void SetSysClock(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 24;
- RCC_OscInitStruct.PLL.PLLN = 336;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
-
- // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
-
-
-}
-
-#elif USE_SYSCLOCK_180 != 0
-/*
- * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
- * and SYSCLK=180MHZ
- */
-void SetSysClock(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8;
- RCC_OscInitStruct.PLL.PLLN = 360;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- HAL_PWREx_EnableOverDrive();
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
-
- // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
-
-}
-#endif
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/device/nvic_addr.h b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/device/nvic_addr.h
deleted file mode 100644
index 307c99edd6..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F439xI/device/nvic_addr.h
+++ /dev/null
@@ -1,40 +0,0 @@
-/* mbed Microcontroller Library
- * Copyright (c) 2017-2017 ARM Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- * http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-#ifndef NVIC_ADDR_H
-#define NVIC_ADDR_H
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-#if defined(__ICCARM__)
- #pragma section=".intvec"
- #define NVIC_FLASH_VECTOR_ADDRESS ((uint32_t)__section_begin(".intvec"))
-#elif defined(__CC_ARM)
- extern uint32_t Load$$LR$$LR_IROM1$$Base[];
- #define NVIC_FLASH_VECTOR_ADDRESS ((uint32_t)Load$$LR$$LR_IROM1$$Base)
-#elif defined(__GNUC__)
- extern uint32_t g_pfnVectors[];
- #define NVIC_FLASH_VECTOR_ADDRESS ((uint32_t)g_pfnVectors)
-#else
- #error "Flash vector address not set for this toolchain"
-#endif
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_B96B_F446VE/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_B96B_F446VE/system_clock.c
new file mode 100644
index 0000000000..a32d0edfa9
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_B96B_F446VE/system_clock.c
@@ -0,0 +1,255 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- PLL_HSE_XTAL | 3- PLL_HSI
+ * | (external 16 MHz xtal) | (internal 16 MHz)
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 180 | 180
+ *-----------------------------------------------------------------------------
+ * AHBCLK (MHz) | 180 | 180
+ *-----------------------------------------------------------------------------
+ * APB1CLK (MHz) | 45 | 45
+ *-----------------------------------------------------------------------------
+ * APB2CLK (MHz) | 90 | 90
+ *-----------------------------------------------------------------------------
+ * USB capable (48 MHz precise clock) | YES | NO
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
+#define USE_PLL_HSE_EXTC (0) /* Use external clock */
+#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
+
+#define DEBUG_MCO (0) // 0=OFF
+// 1=Output the MCO1 on PA8
+// 2=Output the MCO2 on PC9
+
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif
+
+uint8_t SetSysClock_PLL_HSI(void);
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+void SetSysClock(void)
+{
+ /* 1- Try to start with HSE and external clock */
+#if USE_PLL_HSE_EXTC != 0
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+ /* 2- If fail try to start with HSE and external xtal */
+#if USE_PLL_HSE_XTAL != 0
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0) {
+ while(1) {
+ // [TODO] Put something here to tell the user that a problem occured...
+ }
+ }
+ }
+ }
+
+ // Output clock on MCO2 pin(PC9) for debugging purpose
+#if DEBUG_MCO == 2
+ HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 180/4 = 45 MHz
+#endif
+}
+
+#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ // Enable HSE oscillator and activate PLL with HSE as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
+ }
+
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; //
+ RCC_OscInitStruct.PLL.PLLR = 6; //
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Activate the OverDrive to reach the 180 MHz Frequency
+ if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Select PLLSAI output as USB clock source
+ PeriphClkInitStruct.PLLSAI.PLLSAIM = 8;
+ PeriphClkInitStruct.PLLSAI.PLLSAIN = 384;
+ PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV8;
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+ PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP;
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Output clock on MCO1 pin(PA8) for debugging purpose
+#if DEBUG_MCO == 1
+ if (bypass == 0)
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 16 MHz with xtal
+ else
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // xx MHz with external clock (MCO)
+#endif
+
+ return 1; // OK
+}
+#endif
+
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ // Enable HSI oscillator and activate PLL with HSI as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; //
+ RCC_OscInitStruct.PLL.PLLQ = 6; //
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 180 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Output clock on MCO1 pin(PA8) for debugging purpose
+#if DEBUG_MCO == 1
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+#endif
+
+ return 1; // OK
+}
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_B96B_F446VE/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_B96B_F446VE/system_stm32f4xx.c
deleted file mode 100644
index 38257d113c..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_B96B_F446VE/system_stm32f4xx.c
+++ /dev/null
@@ -1,955 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_XTAL | 3- PLL_HSI
- * | (external 16 MHz xtal) | (internal 16 MHz)
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 180 | 180
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 180 | 180
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 45 | 45
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 90 | 90
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)16000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (0) /* Use external clock */
-#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
-
-#define DEBUG_MCO (0) // 0=OFF
- // 1=Output the MCO1 on PA8
- // 2=Output the MCO2 on PC9
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 16000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- // Output clock on MCO2 pin(PC9) for debugging purpose
-#if DEBUG_MCO == 2
- HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 180/4 = 45 MHz
-#endif
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- // Enable HSE oscillator and activate PLL with HSE as source
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
- }
-
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7; //
- RCC_OscInitStruct.PLL.PLLR = 6; //
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Activate the OverDrive to reach the 180 MHz Frequency
- if (HAL_PWREx_EnableOverDrive() != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Select PLLSAI output as USB clock source
- PeriphClkInitStruct.PLLSAI.PLLSAIM = 8;
- PeriphClkInitStruct.PLLSAI.PLLSAIN = 384;
- PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV8;
- PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
- PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP;
- HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
-
- // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Output clock on MCO1 pin(PA8) for debugging purpose
-#if DEBUG_MCO == 1
- if (bypass == 0)
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 16 MHz with xtal
- else
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // xx MHz with external clock (MCO)
-#endif
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- // Enable HSI oscillator and activate PLL with HSI as source
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7; //
- RCC_OscInitStruct.PLL.PLLQ = 6; //
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 180 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Output clock on MCO1 pin(PA8) for debugging purpose
-#if DEBUG_MCO == 1
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-#endif
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446RE/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446RE/system_clock.c
new file mode 100644
index 0000000000..48acec0abe
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446RE/system_clock.c
@@ -0,0 +1,281 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- USE_PLL_HSE_EXTC | 3- USE_PLL_HSI
+ * | (external 8 MHz clock) | (internal 16 MHz)
+ * | 2- USE_PLL_HSE_XTAL |
+ * | (external 8 MHz xtal) |
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 180 | 180
+ *-----------------------------------------------------------------------------
+ * AHBCLK (MHz) | 180 | 180
+ *-----------------------------------------------------------------------------
+ * APB1CLK (MHz) | 45 | 45
+ *-----------------------------------------------------------------------------
+ * APB2CLK (MHz) | 90 | 90
+ *-----------------------------------------------------------------------------
+ * USB capable (48 MHz precise clock) | YES | YES (HSI calibration needed)
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+#include "mbed_assert.h"
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+
+// clock source is selected with CLOCK_SOURCE in json config
+#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
+#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
+#define USE_PLL_HSI 0x2 // Use HSI internal clock
+
+//#define DEBUG_MCO (1) // Output the MCO1/MCO2 on PA8/PC9 for debugging (0=OFF, 1=ON)
+
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+uint8_t SetSysClock_PLL_HSI(void);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+
+void SetSysClock(void)
+{
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
+ /* 1- Try to start with HSE and external clock */
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
+ /* 2- If fail try to start with HSE and external xtal */
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0)
+#endif
+ {
+ while(1) {
+ MBED_ASSERT(1);
+ }
+ }
+ }
+ }
+
+ // Output clock on MCO2 pin(PC9) for debugging purpose
+#if DEBUG_MCO == 1
+ HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
+#endif
+}
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ // Enable HSE oscillator and activate PLL with HSE as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
+ }
+
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; //
+ RCC_OscInitStruct.PLL.PLLR = 2; //
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Activate the OverDrive to reach the 180 MHz Frequency
+ if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Select PLLSAI output as USB clock source
+ PeriphClkInitStruct.PLLSAI.PLLSAIM = 8;
+ PeriphClkInitStruct.PLLSAI.PLLSAIN = 384;
+ PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV8;
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+ PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP;
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Output clock on MCO1 pin(PA8) for debugging purpose
+#if DEBUG_MCO == 1
+ if (bypass == 0)
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
+ else
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock (MCO)
+#endif
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_RCC_PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ // Enable HSI oscillator and activate PLL with HSI as source
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; //
+ RCC_OscInitStruct.PLL.PLLQ = 6; //
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Activate the OverDrive to reach the 180 MHz Frequency
+ if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Select PLLSAI output as USB clock source
+ PeriphClkInitStruct.PLLSAI.PLLSAIM = 8;
+ PeriphClkInitStruct.PLLSAI.PLLSAIN = 192;
+ PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV8;
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+ PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP;
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Output clock on MCO1 pin(PA8) for debugging purpose
+#if DEBUG_MCO == 1
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+#endif
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446RE/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446RE/system_stm32f4xx.c
deleted file mode 100644
index 2470174603..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446RE/system_stm32f4xx.c
+++ /dev/null
@@ -1,955 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 180 | 180
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 180 | 180
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 45 | 45
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 90 | 90
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (1) /* Use external clock */
-#define USE_PLL_HSE_XTAL (0) /* Use external xtal */
-#define DEBUG_MCO (1) // Output the MCO1/MCO2 on PA8/PC9 for debugging (0=OFF, 1=ON)
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 16000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
- #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- // Output clock on MCO2 pin(PC9) for debugging purpose
-#if DEBUG_MCO == 1
- HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
-#endif
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- // Enable HSE oscillator and activate PLL with HSE as source
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
- }
-
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7; //
- RCC_OscInitStruct.PLL.PLLR = 2; //
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Activate the OverDrive to reach the 180 MHz Frequency
- if (HAL_PWREx_EnableOverDrive() != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Select PLLSAI output as USB clock source
- PeriphClkInitStruct.PLLSAI.PLLSAIM = 8;
- PeriphClkInitStruct.PLLSAI.PLLSAIN = 384;
- PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV8;
- PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
- PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP;
- HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
-
- // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Output clock on MCO1 pin(PA8) for debugging purpose
-#if DEBUG_MCO == 1
- if (bypass == 0)
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
- else
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock (MCO)
-#endif
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- // Enable HSI oscillator and activate PLL with HSI as source
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7; //
- RCC_OscInitStruct.PLL.PLLQ = 6; //
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 180 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Output clock on MCO1 pin(PA8) for debugging purpose
-#if DEBUG_MCO == 1
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-#endif
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446ZE/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446ZE/system_clock.c
new file mode 100644
index 0000000000..c7dd0e6768
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446ZE/system_clock.c
@@ -0,0 +1,275 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- USE_PLL_HSE_EXTC (external 8 MHz clock)
+ * | 2- USE_PLL_HSE_XTAL (external 8 MHz xtal)
+ * | 3- USE_PLL_HSI (internal 16 MHz)
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 180
+ * AHBCLK (MHz) | 180
+ * APB1CLK (MHz) | 45
+ * APB2CLK (MHz) | 90
+ * USB capable | YES
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+#include "mbed_assert.h"
+
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+
+// clock source is selected with CLOCK_SOURCE in json config
+#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
+#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
+#define USE_PLL_HSI 0x2 // Use HSI internal clock
+
+//#define DEBUG_MCO (1) // Output the MCO1/MCO2 on PA8/PC9 for debugging (0=OFF, 1=ON)
+
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+uint8_t SetSysClock_PLL_HSI(void);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+
+void SetSysClock(void)
+{
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
+ /* 1- Try to start with HSE and external clock */
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
+ /* 2- If fail try to start with HSE and external xtal */
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0)
+#endif
+ {
+ while(1) {
+ MBED_ASSERT(1);
+ }
+ }
+ }
+ }
+
+ // Output clock on MCO2 pin(PC9) for debugging purpose
+#if DEBUG_MCO == 1
+ HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
+#endif
+}
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSE oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
+ }
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; //
+ RCC_OscInitStruct.PLL.PLLR = 2; //
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Activate the OverDrive to reach the 180 MHz Frequency
+ if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Select PLLSAI output as USB clock source
+ PeriphClkInitStruct.PLLSAI.PLLSAIM = 8;
+ PeriphClkInitStruct.PLLSAI.PLLSAIN = 384;
+ PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV8;
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+ PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP;
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Output clock on MCO1 pin(PA8) for debugging purpose
+#if DEBUG_MCO == 1
+ if (bypass == 0)
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
+ else
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock (MCO)
+#endif
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSI oscillator and activate PLL with HSI as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; //
+ RCC_OscInitStruct.PLL.PLLR = 6; //
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLLSAI output as USB clock source */
+ PeriphClkInitStruct.PLLSAI.PLLSAIM = 8;
+ PeriphClkInitStruct.PLLSAI.PLLSAIN = 192;
+ PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV8;
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+ PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP;
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 180 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Output clock on MCO1 pin(PA8) for debugging purpose
+#if DEBUG_MCO == 1
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+#endif
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446ZE/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446ZE/system_stm32f4xx.c
deleted file mode 100644
index 2470174603..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F446xE/TARGET_NUCLEO_F446ZE/system_stm32f4xx.c
+++ /dev/null
@@ -1,955 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *-----------------------------------------------------------------------------
- * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
- * | (external 8 MHz clock) | (internal 16 MHz)
- * | 2- PLL_HSE_XTAL |
- * | (external 8 MHz xtal) |
- *-----------------------------------------------------------------------------
- * SYSCLK(MHz) | 180 | 180
- *-----------------------------------------------------------------------------
- * AHBCLK (MHz) | 180 | 180
- *-----------------------------------------------------------------------------
- * APB1CLK (MHz) | 45 | 45
- *-----------------------------------------------------------------------------
- * APB2CLK (MHz) | 90 | 90
- *-----------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *-----------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
-#define USE_PLL_HSE_EXTC (1) /* Use external clock */
-#define USE_PLL_HSE_XTAL (0) /* Use external xtal */
-#define DEBUG_MCO (1) // Output the MCO1/MCO2 on PA8/PC9 for debugging (0=OFF, 1=ON)
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
-uint32_t SystemCoreClock = 16000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
-#endif
-
-uint8_t SetSysClock_PLL_HSI(void);
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
- #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- /* 1- Try to start with HSE and external clock */
-#if USE_PLL_HSE_EXTC != 0
- if (SetSysClock_PLL_HSE(1) == 0)
-#endif
- {
- /* 2- If fail try to start with HSE and external xtal */
- #if USE_PLL_HSE_XTAL != 0
- if (SetSysClock_PLL_HSE(0) == 0)
- #endif
- {
- /* 3- If fail start with HSI clock */
- if (SetSysClock_PLL_HSI() == 0)
- {
- while(1)
- {
- // [TODO] Put something here to tell the user that a problem occured...
- }
- }
- }
- }
-
- // Output clock on MCO2 pin(PC9) for debugging purpose
-#if DEBUG_MCO == 1
- HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
-#endif
-}
-
-#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
-/******************************************************************************/
-/* PLL (clocked by HSE) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- // Enable HSE oscillator and activate PLL with HSE as source
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- if (bypass == 0)
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
- }
- else
- {
- RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
- }
-
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
- RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7; //
- RCC_OscInitStruct.PLL.PLLR = 2; //
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Activate the OverDrive to reach the 180 MHz Frequency
- if (HAL_PWREx_EnableOverDrive() != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Select PLLSAI output as USB clock source
- PeriphClkInitStruct.PLLSAI.PLLSAIM = 8;
- PeriphClkInitStruct.PLLSAI.PLLSAIN = 384;
- PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV8;
- PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
- PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP;
- HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
-
- // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Output clock on MCO1 pin(PA8) for debugging purpose
-#if DEBUG_MCO == 1
- if (bypass == 0)
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
- else
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock (MCO)
-#endif
-
- return 1; // OK
-}
-#endif
-
-/******************************************************************************/
-/* PLL (clocked by HSI) used as System clock source */
-/******************************************************************************/
-uint8_t SetSysClock_PLL_HSI(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- /* The voltage scaling allows optimizing the power consumption when the device is
- clocked below the maximum system frequency, to update the voltage scaling value
- regarding system frequency refer to product datasheet. */
- __HAL_RCC_PWR_CLK_ENABLE();
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- // Enable HSI oscillator and activate PLL with HSI as source
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSIState = RCC_HSI_ON;
- RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
- RCC_OscInitStruct.HSICalibrationValue = 16;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
- RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
- RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
- RCC_OscInitStruct.PLL.PLLQ = 7; //
- RCC_OscInitStruct.PLL.PLLQ = 6; //
- if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
- RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 180 MHz
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
- if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
- {
- return 0; // FAIL
- }
-
- // Output clock on MCO1 pin(PA8) for debugging purpose
-#if DEBUG_MCO == 1
- HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
-#endif
-
- return 1; // OK
-}
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F469xI/TARGET_DISCO_F469NI/system_clock.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F469xI/TARGET_DISCO_F469NI/system_clock.c
new file mode 100644
index 0000000000..99ddc83cba
--- /dev/null
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F469xI/TARGET_DISCO_F469NI/system_clock.c
@@ -0,0 +1,273 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+* http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+ * This file configures the system clock as follows:
+ *-----------------------------------------------------------------------------
+ * System clock source | 1- USE_PLL_HSE_EXTC (external 8 MHz clock)
+ * | 2- USE_PLL_HSE_XTAL (external 8 MHz xtal)
+ * | 3- USE_PLL_HSI (internal 16 MHz)
+ *-----------------------------------------------------------------------------
+ * SYSCLK(MHz) | 180
+ * AHBCLK (MHz) | 180
+ * APB1CLK (MHz) | 45
+ * APB2CLK (MHz) | 90
+ * USB capable | YES
+ *-----------------------------------------------------------------------------
+**/
+
+#include "stm32f4xx.h"
+#include "mbed_assert.h"
+
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+
+
+// clock source is selected with CLOCK_SOURCE in json config
+#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
+#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
+#define USE_PLL_HSI 0x2 // Use HSI internal clock
+
+//#define DEBUG_MCO (1) // Output the MCO1/MCO2 on PA8/PC9 for debugging (0=OFF, 1=ON)
+
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+uint8_t SetSysClock_PLL_HSI(void);
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
+
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+#endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+}
+
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+
+void SetSysClock(void)
+{
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
+ /* 1- Try to start with HSE and external clock */
+ if (SetSysClock_PLL_HSE(1) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
+ /* 2- If fail try to start with HSE and external xtal */
+ if (SetSysClock_PLL_HSE(0) == 0)
+#endif
+ {
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+ /* 3- If fail start with HSI clock */
+ if (SetSysClock_PLL_HSI() == 0)
+#endif
+ {
+ while(1) {
+ MBED_ASSERT(1);
+ }
+ }
+ }
+ }
+
+ // Output clock on MCO2 pin(PC9) for debugging purpose
+#if DEBUG_MCO == 1
+ HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4);
+#endif
+}
+
+#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSE oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ if (bypass == 0) {
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
+ } else {
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
+ }
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
+ RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; //
+ RCC_OscInitStruct.PLL.PLLR = 2; //
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Activate the OverDrive to reach the 180 MHz Frequency
+ if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Select PLLSAI output as USB clock source
+ PeriphClkInitStruct.PLLSAI.PLLSAIN = 192;
+ PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV4;
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+ PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP;
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Output clock on MCO1 pin(PA8) for debugging purpose
+#if DEBUG_MCO == 1
+ if (bypass == 0)
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz with xtal
+ else
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz with external clock (MCO)
+#endif
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
+
+#if ((CLOCK_SOURCE) & USE_PLL_HSI)
+/******************************************************************************/
+/* PLL (clocked by HSI) used as System clock source */
+/******************************************************************************/
+uint8_t SetSysClock_PLL_HSI(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /* Enable Power Control clock */
+ __HAL_RCC_PWR_CLK_ENABLE();
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ /* Enable HSI oscillator and activate PLL with HSI as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+ RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+ RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
+ RCC_OscInitStruct.PLL.PLLN = 360; // VCO output clock = 360 MHz (1 MHz * 360)
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 180 MHz (360 MHz / 2)
+ RCC_OscInitStruct.PLL.PLLQ = 7; //
+ RCC_OscInitStruct.PLL.PLLR = 6; //
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ /* Select PLLSAI output as USB clock source */
+ PeriphClkInitStruct.PLLSAI.PLLSAIN = 192;
+ PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV4;
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
+ PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP;
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 180 MHz
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 MHz
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
+ return 0; // FAIL
+ }
+
+ // Output clock on MCO1 pin(PA8) for debugging purpose
+#if DEBUG_MCO == 1
+ HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
+#endif
+
+ return 1; // OK
+}
+#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F469xI/TARGET_DISCO_F469NI/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F469xI/TARGET_DISCO_F469NI/system_stm32f4xx.c
deleted file mode 100644
index 3acd6b5dae..0000000000
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F469xI/TARGET_DISCO_F469NI/system_stm32f4xx.c
+++ /dev/null
@@ -1,877 +0,0 @@
-/**
- ******************************************************************************
- * @file system_stm32f4xx.c
- * @author MCD Application Team
- * @version V2.6.1
- * @date 14-February-2017
- * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
- *
- * This file provides two functions and one global variable to be called from
- * user application:
- * - SystemInit(): This function is called at startup just after reset and
- * before branch to main program. This call is made inside
- * the "startup_stm32f4xx.s" file.
- *
- * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
- * by the user application to setup the SysTick
- * timer or configure other parameters.
- *
- * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
- * be called whenever the core clock is changed
- * during program execution.
- *
- * This file configures the system clock as follows:
- *--------------------------------------------------------------------------------------
- * System clock source | PLL_HSE_XTAL | PLL_HSE_XTAL
- * | (external 8 MHz clock) | (external 8 MHz clock)
- *--------------------------------------------------------------------------------------
- * SYSCLK(MHz) | 168 | 180
- *--------------------------------------------------------------------------------------
- * AHBCLK (MHz) | 168 | 180
- *--------------------------------------------------------------------------------------
- * APB1CLK (MHz) | 42 | 45
- *--------------------------------------------------------------------------------------
- * APB2CLK (MHz) | 84 | 90
- *--------------------------------------------------------------------------------------
- * USB capable (48 MHz precise clock) | YES | NO
- *--------------------------------------------------------------------------------------
- ******************************************************************************
- * @attention
- *
- * © COPYRIGHT 2017 STMicroelectronics
- *
- * Redistribution and use in source and binary forms, with or without modification,
- * are permitted provided that the following conditions are met:
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- * 3. Neither the name of STMicroelectronics nor the names of its contributors
- * may be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
- * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
- * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
- * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
- * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- ******************************************************************************
- */
-
-/** @addtogroup CMSIS
- * @{
- */
-
-/** @addtogroup stm32f4xx_system
- * @{
- */
-
-/** @addtogroup STM32F4xx_System_Private_Includes
- * @{
- */
-
-
-#include "stm32f4xx.h"
-
-#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
-#endif /* HSE_VALUE */
-
-#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
-#endif /* HSI_VALUE */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
- * @{
- */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Defines
- * @{
- */
-
-/************************* Miscellaneous Configuration ************************/
-/*!< Uncomment the following line if you need to use external SRAM or SDRAM as data memory */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-/* #define DATA_IN_ExtSRAM */
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx ||\
- STM32F412Zx || STM32F412Vx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-/* #define DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx ||\
- STM32F479xx */
-
-/*!< Uncomment the following line if you need to relocate your vector Table in
- Internal SRAM. */
-/* #define VECT_TAB_SRAM */
-#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
- This value must be a multiple of 0x200. */
-/******************************************************************************/
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Macros
- * @{
- */
-
-/* Select the SYSCLOCK to start with (0=OFF, 1=ON) */
-#define USE_SYSCLOCK_168 (1) /* Use external 8MHz xtal and sets SYSCLK to 168MHz */
-#define USE_SYSCLOCK_180 (0) /* Use external 8MHz xtal and sets SYSCLK to 180MHz */
-
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Variables
- * @{
- */
- /* This variable is updated in three ways:
- 1) by calling CMSIS function SystemCoreClockUpdate()
- 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
- 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
- Note: If you use this function to configure the system clock; then there
- is no need to call the 2 first functions listed above, since SystemCoreClock
- variable is updated automatically.
- */
- uint32_t SystemCoreClock = 168000000;
-const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
-const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
- * @{
- */
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- static void SystemInit_ExtMemCtl(void);
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
-void SystemClock_Config(void);
-/**
- * @}
- */
-
-/** @addtogroup STM32F4xx_System_Private_Functions
- * @{
- */
-
-/**
- * @brief Setup the microcontroller system
- * Initialize the FPU setting, vector table location and External memory
- * configuration.
- * @param None
- * @retval None
- */
-void SystemInit(void)
-{
- /* FPU settings ------------------------------------------------------------*/
- #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
- SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
- #endif
- /* Reset the RCC clock configuration to the default reset state ------------*/
- /* Set HSION bit */
- RCC->CR |= (uint32_t)0x00000001;
-
- /* Reset CFGR register */
- RCC->CFGR = 0x00000000;
-
- /* Reset HSEON, CSSON and PLLON bits */
- RCC->CR &= (uint32_t)0xFEF6FFFF;
-
- /* Reset PLLCFGR register */
- RCC->PLLCFGR = 0x24003010;
-
- /* Reset HSEBYP bit */
- RCC->CR &= (uint32_t)0xFFFBFFFF;
-
- /* Disable all interrupts */
- RCC->CIR = 0x00000000;
-
-#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
- SystemInit_ExtMemCtl();
-#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
-
- /* Configure the Vector Table location add offset address ------------------*/
-#ifdef VECT_TAB_SRAM
- SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
-#else
- SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
-#endif
-
-}
-
-/**
- * @brief Update SystemCoreClock variable according to Clock Register Values.
- * The SystemCoreClock variable contains the core clock (HCLK), it can
- * be used by the user application to setup the SysTick timer or configure
- * other parameters.
- *
- * @note Each time the core clock (HCLK) changes, this function must be called
- * to update SystemCoreClock variable value. Otherwise, any configuration
- * based on this variable will be incorrect.
- *
- * @note - The system frequency computed by this function is not the real
- * frequency in the chip. It is calculated based on the predefined
- * constant and the selected clock source:
- *
- * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
- *
- * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
- *
- * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
- * or HSI_VALUE(*) multiplied/divided by the PLL factors.
- *
- * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
- * 16 MHz) but the real value may vary depending on the variations
- * in voltage and temperature.
- *
- * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
- * depends on the application requirements), user has to ensure that HSE_VALUE
- * is same as the real frequency of the crystal used. Otherwise, this function
- * may have wrong result.
- *
- * - The result of this function could be not correct when using fractional
- * value for HSE crystal.
- *
- * @param None
- * @retval None
- */
-void SystemCoreClockUpdate(void)
-{
- uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
-
- /* Get SYSCLK source -------------------------------------------------------*/
- tmp = RCC->CFGR & RCC_CFGR_SWS;
-
- switch (tmp)
- {
- case 0x00: /* HSI used as system clock source */
- SystemCoreClock = HSI_VALUE;
- break;
- case 0x04: /* HSE used as system clock source */
- SystemCoreClock = HSE_VALUE;
- break;
- case 0x08: /* PLL used as system clock source */
-
- /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
- SYSCLK = PLL_VCO / PLL_P
- */
- pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
- pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
-
- if (pllsource != 0)
- {
- /* HSE used as PLL clock source */
- pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
- else
- {
- /* HSI used as PLL clock source */
- pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
- }
-
- pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
- SystemCoreClock = pllvco/pllp;
- break;
- default:
- SystemCoreClock = HSI_VALUE;
- break;
- }
- /* Compute HCLK frequency --------------------------------------------------*/
- /* Get HCLK prescaler */
- tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
- /* HCLK frequency */
- SystemCoreClock >>= tmp;
-}
-
-#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface clock */
- RCC->AHB1ENR |= 0x000001F8;
-
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
- FMC_Bank5_6->SDCMR = 0x00000073;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
- FMC_Bank5_6->SDCMR = 0x00046014;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-
- (void)(tmp);
-}
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-#elif defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
-/**
- * @brief Setup the external memory controller.
- * Called in startup_stm32f4xx.s before jump to main.
- * This function configures the external memories (SRAM/SDRAM)
- * This SRAM/SDRAM will be used as program data memory (including heap and stack).
- * @param None
- * @retval None
- */
-void SystemInit_ExtMemCtl(void)
-{
- __IO uint32_t tmp = 0x00;
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
-#if defined (DATA_IN_ExtSDRAM)
- register uint32_t tmpreg = 0, timeout = 0xFFFF;
- register __IO uint32_t index;
-
-#if defined(STM32F446xx)
- /* Enable GPIOA, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG interface
- clock */
- RCC->AHB1ENR |= 0x0000007D;
-#else
- /* Enable GPIOC, GPIOD, GPIOE, GPIOF, GPIOG, GPIOH and GPIOI interface
- clock */
- RCC->AHB1ENR |= 0x000001F8;
-#endif /* STM32F446xx */
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOCEN);
-
-#if defined(STM32F446xx)
- /* Connect PAx pins to FMC Alternate function */
- GPIOA->AFR[0] |= 0xC0000000;
- GPIOA->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOA->MODER |= 0x00008000;
- /* Configure PDx pins speed to 50 MHz */
- GPIOA->OSPEEDR |= 0x00008000;
- /* Configure PDx pins Output type to push-pull */
- GPIOA->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOA->PUPDR |= 0x00000000;
-
- /* Connect PCx pins to FMC Alternate function */
- GPIOC->AFR[0] |= 0x00CC0000;
- GPIOC->AFR[1] |= 0x00000000;
- /* Configure PDx pins in Alternate function mode */
- GPIOC->MODER |= 0x00000A00;
- /* Configure PDx pins speed to 50 MHz */
- GPIOC->OSPEEDR |= 0x00000A00;
- /* Configure PDx pins Output type to push-pull */
- GPIOC->OTYPER |= 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOC->PUPDR |= 0x00000000;
-#endif /* STM32F446xx */
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x000000CC;
- GPIOD->AFR[1] = 0xCC000CCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xA02A000A;
- /* Configure PDx pins speed to 50 MHz */
- GPIOD->OSPEEDR = 0xA02A000A;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00000CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA800A;
- /* Configure PEx pins speed to 50 MHz */
- GPIOE->OSPEEDR = 0xAAAA800A;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0xCCCCCCCC;
- GPIOF->AFR[1] = 0xCCCCCCCC;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA800AAA;
- /* Configure PFx pins speed to 50 MHz */
- GPIOF->OSPEEDR = 0xAA800AAA;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0xCCCCCCCC;
- GPIOG->AFR[1] = 0xCCCCCCCC;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0xAAAAAAAA;
- /* Configure PGx pins speed to 50 MHz */
- GPIOG->OSPEEDR = 0xAAAAAAAA;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx)
- /* Connect PHx pins to FMC Alternate function */
- GPIOH->AFR[0] = 0x00C0CC00;
- GPIOH->AFR[1] = 0xCCCCCCCC;
- /* Configure PHx pins in Alternate function mode */
- GPIOH->MODER = 0xAAAA08A0;
- /* Configure PHx pins speed to 50 MHz */
- GPIOH->OSPEEDR = 0xAAAA08A0;
- /* Configure PHx pins Output type to push-pull */
- GPIOH->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PHx pins */
- GPIOH->PUPDR = 0x00000000;
-
- /* Connect PIx pins to FMC Alternate function */
- GPIOI->AFR[0] = 0xCCCCCCCC;
- GPIOI->AFR[1] = 0x00000CC0;
- /* Configure PIx pins in Alternate function mode */
- GPIOI->MODER = 0x0028AAAA;
- /* Configure PIx pins speed to 50 MHz */
- GPIOI->OSPEEDR = 0x0028AAAA;
- /* Configure PIx pins Output type to push-pull */
- GPIOI->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PIx pins */
- GPIOI->PUPDR = 0x00000000;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
-
-/*-- FMC Configuration -------------------------------------------------------*/
- /* Enable the FMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
-
- /* Configure and enable SDRAM bank1 */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCR[0] = 0x00001954;
-#else
- FMC_Bank5_6->SDCR[0] = 0x000019E4;
-#endif /* STM32F446xx */
- FMC_Bank5_6->SDTR[0] = 0x01115351;
-
- /* SDRAM initialization sequence */
- /* Clock enable command */
- FMC_Bank5_6->SDCMR = 0x00000011;
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Delay */
- for (index = 0; index<1000; index++);
-
- /* PALL command */
- FMC_Bank5_6->SDCMR = 0x00000012;
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Auto refresh command */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x000000F3;
-#else
- FMC_Bank5_6->SDCMR = 0x00000073;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* MRD register program */
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDCMR = 0x00044014;
-#else
- FMC_Bank5_6->SDCMR = 0x00046014;
-#endif /* STM32F446xx */
- timeout = 0xFFFF;
- while((tmpreg != 0) && (timeout-- > 0))
- {
- tmpreg = FMC_Bank5_6->SDSR & 0x00000020;
- }
-
- /* Set refresh count */
- tmpreg = FMC_Bank5_6->SDRTR;
-#if defined(STM32F446xx)
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000050C<<1));
-#else
- FMC_Bank5_6->SDRTR = (tmpreg | (0x0000027C<<1));
-#endif /* STM32F446xx */
-
- /* Disable write protection */
- tmpreg = FMC_Bank5_6->SDCR[0];
- FMC_Bank5_6->SDCR[0] = (tmpreg & 0xFFFFFDFF);
-#endif /* DATA_IN_ExtSDRAM */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)\
- || defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
- || defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx)
-
-#if defined(DATA_IN_ExtSRAM)
-/*-- GPIOs Configuration -----------------------------------------------------*/
- /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
- RCC->AHB1ENR |= 0x00000078;
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);
-
- /* Connect PDx pins to FMC Alternate function */
- GPIOD->AFR[0] = 0x00CCC0CC;
- GPIOD->AFR[1] = 0xCCCCCCCC;
- /* Configure PDx pins in Alternate function mode */
- GPIOD->MODER = 0xAAAA0A8A;
- /* Configure PDx pins speed to 100 MHz */
- GPIOD->OSPEEDR = 0xFFFF0FCF;
- /* Configure PDx pins Output type to push-pull */
- GPIOD->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PDx pins */
- GPIOD->PUPDR = 0x00000000;
-
- /* Connect PEx pins to FMC Alternate function */
- GPIOE->AFR[0] = 0xC00CC0CC;
- GPIOE->AFR[1] = 0xCCCCCCCC;
- /* Configure PEx pins in Alternate function mode */
- GPIOE->MODER = 0xAAAA828A;
- /* Configure PEx pins speed to 100 MHz */
- GPIOE->OSPEEDR = 0xFFFFC3CF;
- /* Configure PEx pins Output type to push-pull */
- GPIOE->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PEx pins */
- GPIOE->PUPDR = 0x00000000;
-
- /* Connect PFx pins to FMC Alternate function */
- GPIOF->AFR[0] = 0x00CCCCCC;
- GPIOF->AFR[1] = 0xCCCC0000;
- /* Configure PFx pins in Alternate function mode */
- GPIOF->MODER = 0xAA000AAA;
- /* Configure PFx pins speed to 100 MHz */
- GPIOF->OSPEEDR = 0xFF000FFF;
- /* Configure PFx pins Output type to push-pull */
- GPIOF->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PFx pins */
- GPIOF->PUPDR = 0x00000000;
-
- /* Connect PGx pins to FMC Alternate function */
- GPIOG->AFR[0] = 0x00CCCCCC;
- GPIOG->AFR[1] = 0x000000C0;
- /* Configure PGx pins in Alternate function mode */
- GPIOG->MODER = 0x00085AAA;
- /* Configure PGx pins speed to 100 MHz */
- GPIOG->OSPEEDR = 0x000CAFFF;
- /* Configure PGx pins Output type to push-pull */
- GPIOG->OTYPER = 0x00000000;
- /* No pull-up, pull-down for PGx pins */
- GPIOG->PUPDR = 0x00000000;
-
-/*-- FMC/FSMC Configuration --------------------------------------------------*/
- /* Enable the FMC/FSMC interface clock */
- RCC->AHB3ENR |= 0x00000001;
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001011;
- FMC_Bank1->BTCR[3] = 0x00000201;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#if defined(STM32F469xx) || defined(STM32F479xx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FMC_Bank1->BTCR[2] = 0x00001091;
- FMC_Bank1->BTCR[3] = 0x00110212;
- FMC_Bank1E->BWTR[2] = 0x0fffffff;
-#endif /* STM32F469xx || STM32F479xx */
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)\
- || defined(STM32F412Zx) || defined(STM32F412Vx)
- /* Delay after an RCC peripheral clock enabling */
- tmp = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FSMCEN);
- /* Configure and enable Bank1_SRAM2 */
- FSMC_Bank1->BTCR[2] = 0x00001011;
- FSMC_Bank1->BTCR[3] = 0x00000201;
- FSMC_Bank1E->BWTR[2] = 0x0FFFFFFF;
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F412Zx || STM32F412Vx */
-
-#endif /* DATA_IN_ExtSRAM */
-#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx ||\
- STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx */
- (void)(tmp);
-}
-#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/** System Clock Configuration
-*/
-#if USE_SYSCLOCK_168 != 0
-/*
- * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
- * and SYSCLK=168MHZ
- */
-void SystemClock_Config(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8;
- RCC_OscInitStruct.PLL.PLLN = 336;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- RCC_OscInitStruct.PLL.PLLR = 2; // I2S clocks
-
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
-
-}
-
-#elif USE_SYSCLOCK_180 != 0
-/*
- * generated code by STM32CubeMX 4.4.0 for board 32F429Discovery
- * and SYSCLK=180MHZ
- */
-void SystemClock_Config(void)
-{
-
- RCC_OscInitTypeDef RCC_OscInitStruct;
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 8;
- RCC_OscInitStruct.PLL.PLLN = 360;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
- RCC_OscInitStruct.PLL.PLLQ = 7;
- RCC_OscInitStruct.PLL.PLLR = 2; // I2S clocks
-
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- HAL_PWREx_EnableOverDrive();
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
- |RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
-
-}
-#endif
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- SystemClock_Config();
-}
-
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/**
- * @}
- */
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F405RG/device/system_stm32f4xx.c b/targets/TARGET_STM/TARGET_STM32F4/device/system_stm32f4xx.c
similarity index 94%
rename from targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F405RG/device/system_stm32f4xx.c
rename to targets/TARGET_STM/TARGET_STM32F4/device/system_stm32f4xx.c
index 9b5b7b26a2..e63b31232e 100644
--- a/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F405RG/device/system_stm32f4xx.c
+++ b/targets/TARGET_STM/TARGET_STM32F4/device/system_stm32f4xx.c
@@ -2,8 +2,8 @@
******************************************************************************
* @file system_stm32f4xx.c
* @author MCD Application Team
- * @version V2.5.0
- * @date 22-April-2016
+ * @version V2.6.1
+ * @date 14-February-2017
* @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
*
* This file provides two functions and one global variable to be called from
@@ -24,7 +24,7 @@
******************************************************************************
* @attention
*
- * © COPYRIGHT 2016 STMicroelectronics
+ * © COPYRIGHT 2017 STMicroelectronics
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
@@ -67,7 +67,7 @@
#include "stm32f4xx.h"
#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)8000000) /*!< Default value of the External oscillator in Hz */
+ #define HSE_VALUE ((uint32_t)25000000) /*!< Default value of the External oscillator in Hz */
#endif /* HSE_VALUE */
#if !defined (HSI_VALUE)
@@ -135,7 +135,7 @@
is no need to call the 2 first functions listed above, since SystemCoreClock
variable is updated automatically.
*/
- uint32_t SystemCoreClock = 48000000;
+uint32_t SystemCoreClock = 16000000;
const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
/**
@@ -158,6 +158,10 @@ const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
* @{
*/
+/*+ MBED */
+#if 0
+/*- MBED */
+
/**
* @brief Setup the microcontroller system
* Initialize the FPU setting, vector table location and External memory
@@ -200,9 +204,12 @@ void SystemInit(void)
#else
SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
#endif
-
}
+/*+ MBED */
+#endif
+/*- MBED */
+
/**
* @brief Update SystemCoreClock variable according to Clock Register Values.
* The SystemCoreClock variable contains the core clock (HCLK), it can
@@ -288,8 +295,8 @@ void SystemCoreClockUpdate(void)
}
#if defined (DATA_IN_ExtSRAM) && defined (DATA_IN_ExtSDRAM)
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
- defined(STM32F469xx) || defined(STM32F479xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)\
+ || defined(STM32F469xx) || defined(STM32F479xx)
/**
* @brief Setup the external memory controller.
* Called in startup_stm32f4xx.s before jump to main.
@@ -750,41 +757,6 @@ void SystemInit_ExtMemCtl(void)
(void)(tmp);
}
#endif /* DATA_IN_ExtSRAM && DATA_IN_ExtSDRAM */
-
-/**
- * @brief Configures the System clock source, PLL Multiplier and Divider factors,
- * AHB/APBx prescalers and Flash settings
- * @note This function should be called only once the RCC clock configuration
- * is reset to the default reset state (done in SystemInit() function).
- * @param None
- * @retval None
- */
-void SetSysClock(void)
-{
- RCC_ClkInitTypeDef RCC_ClkInitStruct;
- RCC_OscInitTypeDef RCC_OscInitStruct;
-
- __HAL_RCC_PWR_CLK_ENABLE();
-
- __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
-
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
- RCC_OscInitStruct.HSEState = RCC_HSE_ON;
- RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
- RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
- RCC_OscInitStruct.PLL.PLLM = 26;
- RCC_OscInitStruct.PLL.PLLN = 192;
- RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4;
- RCC_OscInitStruct.PLL.PLLQ = 4;
- HAL_RCC_OscConfig(&RCC_OscInitStruct);
-
- RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
- RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
- RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
- RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
- RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
- HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
-}
/**
* @}
*/
diff --git a/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/device/nvic_addr.h b/targets/TARGET_STM/nvic_addr.h
similarity index 100%
rename from targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F429xI/device/nvic_addr.h
rename to targets/TARGET_STM/nvic_addr.h
diff --git a/targets/targets.json b/targets/targets.json
index 1b6ef220ea..2f614228e3 100644
--- a/targets/targets.json
+++ b/targets/targets.json
@@ -835,6 +835,13 @@
"supported_form_factors": ["ARDUINO", "MORPHO"],
"core": "Cortex-M4F",
"extra_labels_add": ["STM32F4", "STM32F401xE", "STM32F401RE"],
+ "config": {
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI",
+ "value": "USE_PLL_HSE_EXTC|USE_PLL_HSE_XTAL|USE_PLL_HSI",
+ "macro_name": "CLOCK_SOURCE"
+ }
+ },
"detect_code": ["0720"],
"macros_add": ["USB_STM_HAL", "USBHOST_OTHER"],
"device_has_add": ["ERROR_RED", "SERIAL_ASYNCH", "SERIAL_FC"],
@@ -846,6 +853,13 @@
"supported_form_factors": ["ARDUINO", "MORPHO"],
"core": "Cortex-M4F",
"extra_labels_add": ["STM32F4", "STM32F410RB","STM32F410xB", "STM32F410Rx"],
+ "config": {
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI",
+ "value": "USE_PLL_HSE_EXTC|USE_PLL_HSE_XTAL|USE_PLL_HSI",
+ "macro_name": "CLOCK_SOURCE"
+ }
+ },
"detect_code": ["0744"],
"device_has_add": ["ANALOGOUT", "ERROR_RED", "LOWPOWERTIMER", "SERIAL_ASYNCH", "SERIAL_FC", "TRNG"],
"release_versions": ["2", "5"],
@@ -857,6 +871,18 @@
"core": "Cortex-M4F",
"extra_labels_add": ["STM32F4", "STM32F411xE", "STM32F411RE"],
"detect_code": ["0740"],
+ "config": {
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI",
+ "value": "USE_PLL_HSE_EXTC|USE_PLL_HSE_XTAL|USE_PLL_HSI",
+ "macro_name": "CLOCK_SOURCE"
+ },
+ "clock_source_usb": {
+ "help": "As 48 Mhz clock is configured for USB, SYSCLK has to be reduced from 100 to 96 MHz (set 0 for the max SYSCLK value)",
+ "value": "0",
+ "macro_name": "CLOCK_SOURCE_USB"
+ }
+ },
"macros_add": ["USB_STM_HAL", "USBHOST_OTHER"],
"device_has_add": ["ERROR_RED", "LOWPOWERTIMER", "SERIAL_ASYNCH", "SERIAL_FC"],
"release_versions": ["2", "5"],
@@ -867,6 +893,13 @@
"supported_form_factors": ["ARDUINO", "MORPHO"],
"core": "Cortex-M4F",
"extra_labels_add": ["STM32F4", "STM32F412xG", "STM32F412ZG"],
+ "config": {
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI",
+ "value": "USE_PLL_HSE_EXTC|USE_PLL_HSE_XTAL|USE_PLL_HSI",
+ "macro_name": "CLOCK_SOURCE"
+ }
+ },
"detect_code": ["0826"],
"macros_add": ["USB_STM_HAL", "USBHOST_OTHER"],
"device_has_add": ["CAN", "ERROR_RED", "LOWPOWERTIMER", "SERIAL_ASYNCH", "SERIAL_FC", "TRNG"],
@@ -878,6 +911,13 @@
"supported_form_factors": ["ARDUINO"],
"core": "Cortex-M4F",
"extra_labels_add": ["STM32F4", "STM32F413xx", "STM32F413ZH", "STM32F413xH"],
+ "config": {
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI",
+ "value": "USE_PLL_HSE_EXTC|USE_PLL_HSE_XTAL|USE_PLL_HSI",
+ "macro_name": "CLOCK_SOURCE"
+ }
+ },
"detect_code": ["0743"],
"macros_add": ["USB_STM_HAL", "USBHOST_OTHER"],
"device_has_add": ["ANALOGOUT", "CAN", "ERROR_RED", "LOWPOWERTIMER", "SERIAL_ASYNCH", "SERIAL_FC", "TRNG"],
@@ -906,6 +946,16 @@
"help": "Value: PA_7 for the default board configuration, PB_5 in case of solder bridge update (SB121 off/ SB122 on)",
"value": "PA_7",
"macro_name": "STM32_D11_SPI_ETHERNET_PIN"
+ },
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI",
+ "value": "USE_PLL_HSE_EXTC|USE_PLL_HSE_XTAL|USE_PLL_HSI",
+ "macro_name": "CLOCK_SOURCE"
+ },
+ "clock_source_usb": {
+ "help": "As 48 Mhz clock is configured for USB, SYSCLK has to be reduced from 180 to 168 MHz (set 0 for the max SYSCLK value)",
+ "value": "1",
+ "macro_name": "CLOCK_SOURCE_USB"
}
},
"extra_labels_add": ["STM32F4", "STM32F429", "STM32F429ZI", "STM32F429xx", "STM32F429xI", "FLASH_CMSIS_ALGO"],
@@ -926,6 +976,16 @@
"help": "Value: PA_7 for the default board configuration, PB_5 in case of solder bridge update (SB121 off/ SB122 on)",
"value": "PA_7",
"macro_name": "STM32_D11_SPI_ETHERNET_PIN"
+ },
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI",
+ "value": "USE_PLL_HSE_EXTC|USE_PLL_HSE_XTAL|USE_PLL_HSI",
+ "macro_name": "CLOCK_SOURCE"
+ },
+ "clock_source_usb": {
+ "help": "As 48 Mhz clock is configured for USB, SYSCLK has to be reduced from 180 to 168 MHz (set 0 for the max SYSCLK value)",
+ "value": "1",
+ "macro_name": "CLOCK_SOURCE_USB"
}
},
"extra_labels_add": ["STM32F4", "STM32F439", "STM32F439ZI", "STM32F439xx", "STM32F439xI", "FLASH_CMSIS_ALGO"],
@@ -942,6 +1002,13 @@
"supported_form_factors": ["ARDUINO", "MORPHO"],
"core": "Cortex-M4F",
"extra_labels_add": ["STM32F4", "STM32F446xE", "STM32F446RE"],
+ "config": {
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI",
+ "value": "USE_PLL_HSE_EXTC|USE_PLL_HSE_XTAL|USE_PLL_HSI",
+ "macro_name": "CLOCK_SOURCE"
+ }
+ },
"detect_code": ["0777"],
"macros_add": ["USB_STM_HAL", "USBHOST_OTHER"],
"device_has_add": ["ANALOGOUT", "CAN", "ERROR_RED", "LOWPOWERTIMER", "SERIAL_ASYNCH", "SERIAL_FC"],
@@ -953,6 +1020,13 @@
"supported_form_factors": ["ARDUINO", "MORPHO"],
"core": "Cortex-M4F",
"extra_labels_add": ["STM32F4", "STM32F446xE", "STM32F446ZE"],
+ "config": {
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI",
+ "value": "USE_PLL_HSE_EXTC|USE_PLL_HSE_XTAL|USE_PLL_HSI",
+ "macro_name": "CLOCK_SOURCE"
+ }
+ },
"detect_code": ["0778"],
"macros_add": ["USB_STM_HAL", "USBHOST_OTHER"],
"device_has_add": ["ANALOGOUT", "CAN", "ERROR_RED", "LOWPOWERTIMER", "SERIAL_ASYNCH", "SERIAL_FC"],
@@ -1096,6 +1170,13 @@
"supported_form_factors": ["ARDUINO", "MORPHO"],
"core": "Cortex-M4F",
"extra_labels_add": ["STM32L4", "STM32L476RG", "STM32L476xG"],
+ "config": {
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI | USE_PLL_MSI (L4)",
+ "value": "USE_PLL_MSI",
+ "macro_name": "CLOCK_SOURCE"
+ }
+ },
"detect_code": ["0765"],
"macros_add": ["USBHOST_OTHER"],
"device_has_add": ["ANALOGOUT", "CAN", "LOWPOWERTIMER", "SERIAL_ASYNCH", "SERIAL_FC", "TRNG", "FLASH"],
@@ -1175,6 +1256,18 @@
"inherits": ["FAMILY_STM32"],
"core": "Cortex-M4F",
"extra_labels_add": ["STM32F4", "STM32F429", "STM32F429ZI", "STM32F429xI", "STM32F429xx", "FLASH_CMSIS_ALGO"],
+ "config": {
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI",
+ "value": "USE_PLL_HSE_XTAL|USE_PLL_HSI",
+ "macro_name": "CLOCK_SOURCE"
+ },
+ "clock_source_usb": {
+ "help": "As 48 Mhz clock is configured for USB, SYSCLK has to be reduced from 180 to 168 MHz (set 0 for the max SYSCLK value)",
+ "value": "1",
+ "macro_name": "CLOCK_SOURCE_USB"
+ }
+ },
"macros_add": ["RTC_LSI=1", "USBHOST_OTHER"],
"device_has_add": ["ANALOGOUT", "CAN", "ERROR_RED", "SERIAL_ASYNCH", "SERIAL_FC", "TRNG", "FLASH"],
"release_versions": ["2", "5"],
@@ -1185,6 +1278,13 @@
"supported_form_factors": ["ARDUINO"],
"core": "Cortex-M4F",
"extra_labels_add": ["STM32F4", "STM32F469", "STM32F469NI", "STM32F469xI", "STM32F469xx"],
+ "config": {
+ "clock_source": {
+ "help": "Mask value : USE_PLL_HSE_EXTC | USE_PLL_HSE_XTAL (need HW patch) | USE_PLL_HSI",
+ "value": "USE_PLL_HSE_XTAL|USE_PLL_HSI",
+ "macro_name": "CLOCK_SOURCE"
+ }
+ },
"detect_code": ["0788"],
"device_has_add": ["ANALOGOUT", "CAN", "ERROR_RED", "LOWPOWERTIMER", "SERIAL_FC", "TRNG"],
"release_versions": ["2", "5"],