2016-03-31 07:28:43 +00:00
|
|
|
/* mbed Microcontroller Library
|
|
|
|
* Copyright (c) 2006-2013 ARM Limited
|
|
|
|
*
|
|
|
|
* Licensed under the Apache License, Version 2.0 (the "License");
|
|
|
|
* you may not use this file except in compliance with the License.
|
|
|
|
* You may obtain a copy of the License at
|
|
|
|
*
|
|
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
|
|
*
|
|
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
|
|
* distributed under the License is distributed on an "AS IS" BASIS,
|
|
|
|
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
|
|
* See the License for the specific language governing permissions and
|
|
|
|
* limitations under the License.
|
|
|
|
*/
|
|
|
|
#ifndef MBED_OBJECTS_H
|
|
|
|
#define MBED_OBJECTS_H
|
|
|
|
|
|
|
|
#include <stdint.h>
|
|
|
|
#include "cmsis.h"
|
|
|
|
#include "PortNames.h"
|
|
|
|
#include "PeripheralNames.h"
|
|
|
|
#include "PinNames.h"
|
|
|
|
#include "gpio_object.h"
|
|
|
|
|
|
|
|
#ifdef __cplusplus
|
|
|
|
extern "C" {
|
|
|
|
#endif
|
|
|
|
|
|
|
|
struct i2c_s {
|
|
|
|
uint32_t i2c;
|
|
|
|
uint32_t dummy;
|
|
|
|
uint8_t pclk_bit;
|
|
|
|
uint8_t width_low;
|
|
|
|
uint8_t width_hi;
|
|
|
|
int bbsy_wait_cnt;
|
|
|
|
int last_stop_flag;
|
|
|
|
};
|
|
|
|
|
|
|
|
struct spi_s {
|
|
|
|
struct st_rspi *spi;
|
|
|
|
uint32_t bits;
|
Commonalize the files in "targets/TARGET_RENESAS/TARGET_RZ_A1XX" directory
I made be available in common whatever the board related to RZ_A1 in the below files.
- Since there are the table code of Pinmap differs for each board, I moved the code to "PeripheralPins" file for each board, and changed to include PeripheralPins.h.
analogin_api.c, can_api.c, gpio_irq_api.c, i2c_api.c, pinmap.c, port_api.c, pwmout_api.c, serial_api.c, spi_api.c and us_ticker.c
- Since there are some board-specific processes, I enclosed the processes with "#ifdef" and rearranged the functions to make be easier to enclose.
can_api.c, ethernet_api.c and serial_api.c
- Since there are the driver configuration values differs for each board, I added "mbed_drv_cfg.h" file for each board and defined macros for the values, and changed to refer to the macros.
can_api.c, gpio_api.c, pwmout_api.c and rtc_api.c
2018-01-09 09:20:50 +00:00
|
|
|
int index;
|
2016-03-31 07:28:43 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
struct gpio_irq_s {
|
|
|
|
uint32_t port;
|
|
|
|
uint32_t pin;
|
|
|
|
uint32_t ch;
|
|
|
|
uint8_t int_enable;
|
|
|
|
};
|
|
|
|
|
|
|
|
struct port_s {
|
|
|
|
__IO uint32_t *reg_dir;
|
|
|
|
__IO uint32_t *reg_out;
|
|
|
|
__I uint32_t *reg_in;
|
|
|
|
__IO uint32_t *reg_buf;
|
|
|
|
PortName port;
|
|
|
|
uint32_t mask;
|
|
|
|
};
|
|
|
|
|
|
|
|
struct serial_s {
|
|
|
|
struct st_scif *uart;
|
|
|
|
int index;
|
|
|
|
};
|
|
|
|
|
|
|
|
struct pwmout_s {
|
|
|
|
uint32_t ch;
|
|
|
|
PWMName pwm;
|
|
|
|
};
|
|
|
|
|
|
|
|
struct analogin_s {
|
|
|
|
ADCName adc;
|
|
|
|
};
|
|
|
|
|
|
|
|
struct can_s {
|
|
|
|
uint32_t ch;
|
|
|
|
};
|
|
|
|
|
2018-01-16 04:45:15 +00:00
|
|
|
struct trng_s {
|
|
|
|
uint8_t dummy;
|
|
|
|
};
|
|
|
|
|
2018-05-21 05:19:07 +00:00
|
|
|
struct flash_s {
|
|
|
|
uint8_t dummy;
|
|
|
|
};
|
|
|
|
|
2016-03-31 07:28:43 +00:00
|
|
|
#ifdef __cplusplus
|
|
|
|
}
|
|
|
|
#endif
|
|
|
|
|
|
|
|
#endif
|